Chapter 4101:1-35 References

3501.1 General. This chapter lists the standards that are referenced in various sections of the building code. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title. The application of the referenced standards shall be as specified in Section 102.5.

3501.2 Referenced codes. When indicated in this code, the following codes refer to provisions in the listed chapters of the administrative code:

 

	
Referenced Code                                                    Ohio Administrative Code Chapters


	
Building Code                                                      4101:1-1 to 4101:1-35


	
Energy Code                                                        4101:1-13


	
Fire Code                                                          1301:7-1 to 1301:7-7


	
Mechanical Code                                                    4101:2-1 to 4101:2-15


	
Ohio Boiler and Pressure Vessel Rules                              4101:4-1 to 4101:4-10


	
Ohio Elevator Code                                                  4101:5-1 to 4101:5-3


	
Residential Code of Ohio for One, Two and Three Family Dwellings  4101:8-1 to 4101:8-44


	
Plumbing Code                                                      4101:3-1 to 4101:3-13

3501.3 Americans with Disabilities Act accessibility guidelines. When reference is made to ADAAG in this code, it shall mean the “ADA Standards for Accessible Design” also known as “ADA Accessibility Guidelines for Buildings and Facilities”, “28 CFR Part 36 Appendix A” Code of Federal Regulations as reprinted and the version available on the U.S. department of justice’s website at http://www.usdoj.gov/crt/ada/stdspdf.htm.

3501.4 Building Code Referenced Standards.

Aluminum Association

1525 Wilson Boulevard, Suite 600

Arlington, VA 22209

 

	
AA Standard reference number  Title


	
ADM1-10                        Aluminum Design Manual: Part 1-A Specification for Aluminum Structures, Allowable Stress Design; and Part 1-B-Aluminum Structures, Load and Resistance Factor Design


	
ASM 35-00                      Aluminum Sheet Metal Work in Building Construction (Fourth Edition)

American Architectural Manufacturers Association

1827 Waldon Office

Square, Suite 550

Schaumburg, IL 60173

 

	
AAMA Standard reference number    Title


	
1402-09                          Standard Specifications for Aluminum Siding, Soffit and Fascia


	
AAMA/WDMA/CSA 101/I.S.2/A440-08  North American Fenestration Standard/Specifications for Windows, Doors and Skylights

American Concrete Institute

38800 Country Club Dive

Farmington Hills, MI 48331

 

	
ACI Standard reference number  Title


	
216.1 -07                      Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies


	
318-08                          Building Code Requirements for Structural Concrete


	
530-08                          Building Code Requirements for Masonry Structures


	
530.1 -08                      Specifications for Masonry Structures

American Forest & Paper Association

1111 19th St, NW Suite 800

Washington, DC 20036

 

	
AF&PA Standard reference number  Title


	
WCD No. 4-03                          Wood Construction Data-Plank and Beam Framing for Residential


	
NDS-05                                National Design Specification (NDS) for Wood Construction with 2005 Supplement


	
AF&PA-93                          Span Tables for Joists and Rafters


	
ANSI/AF&PA PWF-07                  Permanent Wood Foundation Design Specification


	
ANSI/AF&PA SDPWS-08              Special Design Provisions for Wind and Seismic

American Institute of Steel Construction

One East Wacker Drive, Suite 3100

Chicago, IL 60601-2001

 

	
AISC Standard reference number  Title


	
341-05                          Seismic Provisions for Structural Steel Buildings, including Supplement No. 1 dated 2005


	
360-05                          Specification for Structural Steel Buildings

American Iron and Steel Institute

1140 Connecticut Avenue

Suite 705

Washington, DC 20036

 

	
AISI Standard reference number  Title


	
S100-07                          North American Specification for the Design of Cold-formed Steel Structural Members


	
S200-08                          North American Standard for Cold-formed Steel Framing-General


	
S210-08                          North American Standard for Cold-formed Steel Framing-Floor and Roof System Design


	
S211-08                          North American Standard for Cold-formed Steel Framing-Wall Stud


	
S212-08                          North American Standard for Cold-formed Steel Framing-Header Design


	
S213-08                          North American Standard for Cold-formed Steel Framing-Lateral Design


	
S214-08                          North American Standard for Cold-formed Steel Framing-Truss Design, with Supplement 2, dated 2008

American Institute of Timber Construction

Suite 140

7012 S. Revere Parkway

Englewood, CO 80112

 

	
AITC Standard reference number  Title


	
AITC Technical Note 7-96          Calculation of Fire Resistance of Glued Laminated Timbers


	
AITC 104-03                      Typical Construction Details


	
AITC 110-01                      Standard Appearance Grades for Structural Glued Laminated


	
AITC 113-01                      Standard for Dimensions of Structural Glued Laminated Timber


	
AITC 117-04                      Standard Specifications for Structural Glued Laminated Timber of Softwood Species


	
AITC 119-96                      Standard Specifications for Structural Glued Laminated Timber of Hardwood


	
AITC200-09                      Manufacturing Quality Control Systems Manual for Structural Glued Laminated Timber


	
ANSI/AITCA 190.1 -07              Structural Glued Laminated Timber

Automotive Lift Institute

P.O. Box 85

Courtland, NY 13045

 

	
ALI Standard reference number  Title


	
ALI ALCTV-2007                  Standard for Automobile Lifts-Safety Requirements for Construction, Testing and Validation (ANSI)

American National Standards Institute

25 West 43rd Street, Fourth Floor

New York, NY 10036

 

	
ANSI Standard reference number  Title


	
A 13.1 -07                      Scheme for the Identification of Piping Systems


	
A 108.1 A-09                      Installation of Ceramic Tile in the Wet-set Method, with Portland Cement


	
A 108.1 B-09                      Installation of Ceramic Tile, quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set orLatex-


	
A 108.4 -09                      Installation of Ceramic Tile with Organic Adhesives or Water-cleanable Tile-setting Epoxy Adhesive


	
A 108.5 -09                      Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex-portland Cement Mortar


	
A 108.6 -09                      Installation of Ceramic Tile with Chemical-resistant,Water Cleanable Tile-setting and -grouting Epoxy


	
A 108.8 -09                      Installation of Ceramic Tile with Chemical-resistant Furan Resin Mortar and Grout


	
A 108.9 -09                      Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout


	
A 108.10 -09                      Installation of Grout in Tilework


	
A 118.1 -10.1                    American National Standard Specifications for Dry-set Portland Cement


	
A 118.3 -10.1                    American National Standard Specifications for Chemical-resistant, Water-cleanable Tile-setting and -grouting Epoxy and Water Cleanable Tile-setting Epoxy


	
A 118.4 -10.1                    American National Standard Specifications for Latex-portland Cement


	
A 118.5 -10.1                    American National Standard Specifications for Chemical Resistant Furan Mortar and Grouts for Tile


	
A 118.8 -10.1                    American National Standard Specifications for Modified Epoxy Emulsion Mortar/Grout


	
A 136.1 -10.1                    American National Standard Specifications for Organic Adhesives for Installation of Ceramic


	
137.1 -08                        American National Standard Specifications for Ceramic Tile


	
A 208.1 -09                      Particleboard


	
Z 97.1 -09                      Safety Glazing Materials Used in Buildings-Safety Performance Specifications and Methods of Test

APA – Engineered Wood Association

7011 South 19th

Tacoma, WA 98466

 

	
APA Standard reference number  Title


	
APA PDS-08                      Panel Design Specification


	
APA PDS Supplement 1-90          Design and Fabrication of Plywood Curved Panels (revised 1995)


	
APA PDS Supplement 2-92          Design and Fabrication of Plywood-lumber Beams (revised 1998


	
APA PDS Supplement 3-96          Design and Fabrication of Plywood Stressed-skin Panels (revised 1996


	
APA PDS Supplement 4-93          Design and Fabrication of Plywood Sandwich Panels (revised 1993)


	
APA PDS Supplement 5-95          Design and Fabrication of All-plywood Beams (revised 1995


	
EWS R540-07                      Builders Tips: Proper Storage and Handling of Glulam Beams


	
EWS S475-07                      Glued Laminated Beam Design Tables


	
EWS S560-10                      Field Notching and Drilling of Glued Laminated Timber Beams


	
EWS T300-07                      Glulam Connection


	
EWS X440-08                      Product Guide- Glulam


	
EWS X450-01                      Glulam in Residential Construction-Western Edition

The Association of Pool & Spa Professionals

2111 Eisenhower Avenue

Alexandria, VA 22314

 

	
APSP Standard reference number  Title


	
ANSI/APSP 7-06                  Standard for Suction Entrapment Avoidance in Swimming Pools, Wading Pools, Spas, Hot Tubs and Catch Basins

American Society of Agricultural and Biological Engineers

2950 Niles Road

St. Joseph, MI 49085

 

	
ASABE Standard reference number  Title


	
EP 484.2-98                      Diaphragm Design of Metal-clad, Post-frame Rectangular Buildings


	
EP 486.1-99                      Shallow-post Foundation Design


	
EP 559 -03                        Design Requirements and Bending Properties for Mechanically Laminated Columns

American Society of Civil Engineers

Structural Engineering Institute

1801 Alexander Bell Drive

Reston, VA 20191-4400

 

	
ASCE/SEI Standard reference number  Title


	
3-91                                  Structural Design of Composite Slabs


	
5-08                                  Building Code Requirements for Masonry


	
6-08                                  Specification for Masonry Structures


	
7-05                                  Minimum Design Loads for Buildings and Other Structures including Supplements No. 1 and 2, excluding Chapter 14 and Appendix 11A


	
8-02                                  Standard Specification for the Design of Cold-formed Stainless Steel Structural Members


	
19-10                                Structural Applications of Steel Cables for Buildings


	
24-05                                Flood Resistant Design and Construction


	
29-05                                Standard Calculation Methods for Structural Fire Protection


	
32-01                                Design and Construction of Frost Protected Shallow Foundations

American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.

1791 Tullie Circle, NE

Atlanta, GA 30329-2305

 

	
ASHRAE Standard Reference Number  Title


	
ASHRAE 90.1 -2007                  Energy Standard for Buildings Except Low-Rise Buildings

American Society of Mechanical Engineers

Three Park Avenue

New York, NY 10016-5990

 

	
ASME Standard reference number    Title


	
A 17.1 /CSA B44-2004              Safety Code for Elevators and Escalators


	
A 18.1 -2003                      Safety Standard for Platform Lifts and Stairway Chairlifts


	
A 90.1 -03                        Safety Standard for Belt Manlifts


	
B 16.18 -2001 (Reaffirmed 2005)  Cast Copper Alloy Solder Joint Pressure Fittings


	
B 16.22 -2001 (Reaffirmed 2005)  Wrought Copper and Copper Alloy Solder Joint Pressure Fittings


	
B 20.1 -2009                      Safety Standard for Conveyors and Related Equipment


	
B 31.3 -2008                      Process Piping

ASTM International

100 Barr Harbor Drive

West Conshohocken, PA 19428-2959

 

	
ASTM Standard reference number  Title


	
A 36/A 36M-08                    Specification for Carbon Structural Steel


	
A 153/A 153M-09                  Specification for Zinc Coating (Hot-dip) on Iron and Steel Hardware


	
A 240/A 240M-10a                  Standard Specification for Chromium and Chromium-nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications


	
A 252-10                          Specification for Welded and Seamless Steel Pipe Piles


	
A 283/A 283M-03(2007)            Specification for Low and Intermediate Tensile


	
A 307-07b                        Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength


	
A 416/A 416M-10                  Specification for Steel Strand, Uncoated Seven-wire for Prestressed Concrete


	
A 463/A 463M-09a                  Standard Specification for Steel Sheet, Aluminum-coated, by the Hot-dip Process


	
A 572/A 572M-07                  Specification for High-strength Low-alloy Columbium-vanadium Structural Steel


	
A 588/A 588M-10                  Specification for High-strength Low-alloy Structural Steel with 50 ksi (345 MPa) Minimum Yield Point to 4 inches (100 mm) Thick


	
A 615/A 615M-09b                  Specification for Deformed and Plain Billet-steel Bars for Concrete Reinforcement


	
A 653/A 653M-09a                  Specification for Steel Sheet, Zinc-coated Galvanized or Zinc-iron Alloy-coated Galvannealed by the Hot-dip Process


	
A 690/A 690M-07                  Standard Specification for High-strength Low-alloy Nickel, Copper, Phosphorus Steel H-piles and Sheet Piling with Atmospheric Corrosion


	
A 706/A 706M-09b                  Resistance for Use in Marine Environments Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement


	
A 722/A 722M-07                  Specification for Uncoated High-strength Steel Bar for Prestressing


	
A 755/A 755M-03(2008)            Specification for Steel Sheet, Metallic-coated by the Hot-dip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products


	
A 792/A 792M-09a                  Specification for Steel Sheet, 55% Aluminum-zinc Alloy-coated by the Hot-dip Process


	
A 875/A 875M-09a                  Standard Specification for Steel Sheet Zinc-5 percent, Aluminum Alloy-coated by the Hot-dip Process


	
A 913/A 913M-07                  Specification for High-strength Low-alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-tempering Process (QST)


	
A 924/A 924M-10                  Standard Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-dip Process


	
A 992/A 992M-06a                  Standard Specification for Structural Shapes


	
B 42-10                          Specification for Seamless Copper Pipe, Standard


	
B 43-09                          Specification for Seamless Red Brass Pipe, Standard Sizes


	
B 68-02                          Specification for Seamless Copper Tube, Bright Annealed (Metric


	
B 88-09                          Specification for Seamless Copper Water Tube


	
B 101-07                          Specification for Lead-coated Copper Sheet and Strip for Building Construction


	
B 209-07                          Specification for Aluminum and Aluminum Alloy Steel and Plate


	
B 251-10                          Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube


	
B 280-08                          Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service


	
B 370-09                          Specification for Cold-rolled Copper Sheet and Strip for Building Construction


	
B 695-04(2009)                  Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel


	
C 5-10                          Specification for Quicklime for Structural


	
C 22/C 22M-00 (2005)e01          Specification for Gypsum


	
C 27-98 (2008)                  Specification for Standard Classification of Fireclay and High-alumina Refractory Brick


	
C 28/C 28M-10                    Specification for Gypsum


	
C 31/C 31M-10                    Practice for Making and Curing Concrete Test Specimens in the Field


	
C 33-08                          Specification for Concrete Aggregates


	
C 34-10                          Specification for Structural Clay Load-bearing Wall Tile


	
C 35-01(2009)                    Specification for Inorganic Aggregates for Use in Gypsum Plaster


	
C 36/C 36M-03                    Specification for Gypsum Wallboard


	
C 37/C 37M-01                    Specification for Gypsum Lath


	
C 55-09                          Specification for Concrete Building Brick


	
C 56-10                          Specification for Structural ClayNonloadBearing Tile


	
C 59/C 59M-00 (2006)              Specification for Gypsum Casting and Molding Plaster


	
C 61/C 61M-00 (2006)              Specification for Gypsum Keene’s


	
C 62-10                          Specification for Building Brick (Solid Masonry Units Made from Clay or Shale


	
C 67-09                          Test Methods of Sampling and Testing Brick and Structural Clay


	
C 73-05                          Specification for Calcium Silicate Face Brick (Sand-lime Brick)


	
C 79-04a                          Specification for Treated Core and Nontreated Core Gypsum Sheathing Board


	
C 90-09                          Specification for Loadbearing Concrete Masonry Units


	
C 91-05                          Specification for Masonry Cement


	
C 94/C 94M-10                    Specification for Ready-mixed


	
C 126-10                          Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick and Solid Masonry Units


	
C 140-10                          Test Method Sampling and Testing Concrete Masonry Units and Related Units


	
C 150-09                          Specification for Portland Cement


	
C 172-10                          Practice for Sampling Freshly Mixed


	
C 199-84 (2005)                  Test Method for Pier Test for Refractory Mortars


	
C 206-03 (2009)                  Specification for Finishing Hydrated Lime


	
C 208-08a                        Specification for Cellulosic Fiber Insulating Board


	
C 212-10                          Specification for Structural Clay Facing Tile


	
C 216-10                          Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale


	
C 270-10                          Specification for Mortar for Unit Masonry


	
C 315-07                          Specification for Clay Flue Liners and Chimney Pots


	
C 317/C 317M-00 (2005)          Specification for Gypsum Concrete


	
C 330-09                          Specification for Lightweight Aggregates for Structural Concrete


	
C 331-05                          Specification for Lightweight Aggregates for Concrete Masonry Units


	
C 406-10                          Specification for Roofing Slate


	
C 442/C 442M-04                  Specification for Gypsum Backing Board and Coreboard and Gypsum Shaftliner Board


	
C 472-99 (2009)                  Specification for Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete


	
C 473-10                          Test Method for Physical Testing of Gypsum Panel Products


	
C 474-05                          Test Methods for Joint Treatment Materials for Gypsum Board Construction


	
C 475-02 (2007)                  Specification for Joint Compound and Joint Tape


	
C 503-10                          Specification for Marble Dimension Stone (Exterior


	
C 514-04 (2009)e1                Specification for Nails for the Application of Gypsum


	
C 516-08                          Specifications for Vermiculite Loose Fill Thermal


	
C 547-07e1                      Specification for Mineral Fiber Pipe Insulation


	
C 549-06                          Specification forPerliteLoose Fill


	
C 552-07                          Standard Specification for Cellular Glass Thermal Insulation


	
C 557-03(2009)e01                Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing


	
C 568-10                          Specification for Limestone Dimension Stone


	
C 578-10                          Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation


	
C 587-04 (2009)                  Specification for Gypsum Veneer Plaster


	
C 588/C 588M-01                  Specification for Gypsum Base for Veneer Plasters


	
C 595-10                          Specification for Blended Hydraulic Cements


	
C 615-10                          Specification for Granite Dimension


	
C 616-10                          Specification for Quartz Dimension Stone


	
C 629-10                          Specification for Slate Dimension


	
C 630/C 630M-03                  Specification for Water-resistant Gypsum Backing Board


	
C 631-09                          Specification for Bonding Compounds for Interior Gypsum Plastering


	
C 635/C 635M-07                  Specification for the Manufacture, Performance and Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel


	
C 636/C 636M-08                  Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels


	
C 645-09a                        Specification for Nonstructural Steel Framing Members


	
C 652-10                          Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale


	
C 728-05 (2010)                  Standard Specification forPerliteThermal Insulation Board


	
C 744-10                          Specification for Prefaced Concrete and Calcium Silicate Masonry


	
C 754-09a                        Specification for Installation of Steel Framing Members to Receive Screw-attached Gypsum Panel Products


	
C 836/C 836M-10                  Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course


	
C 840-08                          Specification for Application and Finishing of Gypsum Board


	
C 841-03 (2008)e1                Specification for Installation of Interior Lathing and Furring


	
C 842-05                          Specification for Application of Interior Gypsum Plaster


	
C 843-99 (2006)                  Specification for Application of Gypsum Veneer Plaster


	
C 844-10                          Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster


	
C 847-10a                        Specification for Metal Lath


	
C 887-05 (2010)                  Specification for Packaged, Dry Combined Materials for Surface Bonding Mortar


	
C 897-05 (2009)                  Specification for Aggregate for Job-mixed Portland Cement-based Plaster


	
C 920-10                          Standard for Specification forElastomericJoint Sealants


	
C 926-06                          Specification for Application of Portland Cement-based Plaster


	
C 931/C 931M-04                  Specification for Exterior Gypsum Soffit Board


	
C 932-06                          Specification for Surface-applied Bonding Compounds Agents for Exterior Plastering


	
C 933-09                          Specification for Welded Wire Lath


	
C 946-10                          Specification for Practice for Construction of Dry-stacked, Surface-bonded Walls


	
C 954-10                          Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 inch ( 0.84 mm) to 0.112 inch ( 2.84 mm) in Thickness


	
C 955-09a                        Standard Specification for Load-bearing Transverse and Axial Steel Studs, Runners Tracks, and Bracing or Bridging, for Screw Application of Gypsum Panel Products and Metal Plaster Bases


	
C 956-04 (2010)                  Specification for Installation of Cast-in-place Reinforced Gypsum


	
C 957-10                          Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane with Integral Wearing Surface


	
C 960-04                          Specification forPredecoratedGypsum Board


	
C 1002-07                        Specification for Steel Self-piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs


	
C 1007-08a                      Specification for Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories


	
C 1019-09                        Test Method of Sampling and Testing Grout


	
C 1029-10                        Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation


	
C 1032-06                        Specification for Woven Wire Plaster Base


	
C 1047-10a                      Specification for Accessories for Gypsum Wallboard and Gypsum Veneer


	
C 1063-08                        Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster


	
C 1088-10                        Specification for Thin Veneer Brick Units Made from Clay or Shale


	
C 1167-03 (2009)                  Specification for Clay Roof Tiles


	
C 1177/C 1177M-08                Specification for Glass Mat Gypsum Substrate for Use as Sheathing


	
C 1178/C 1178M-08                Specification for Coated Glass Mat Water-resistant Gypsum Backing Panel


	
C 1186-08                        Specification for Flat-Fiber Cement Sheets


	
C 1261-10                        Specification for Firebox Brick for Residential Fireplaces


	
C 1278/C 1278M-07a              Specification for Fiber-reinforced Gypsum Panels


	
C 1280-09                        Specification for Application of Gypsum Sheathing


	
C 1283-07a                      Practice for Installing Clay Flue Lining.


	
C 1288-99 (2010)                  Standard Specification for Discrete Nonasbestos Fiber-cement Interior Substrate Sheets


	
C 1289-10                        Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board


	
C 1314-10                        Test Method for Compressive Strength of Masonry Prisms


	
C 1325-08b                      Standard Specification for Nonasbestos Fiber-mat Reinforced Cement Interior Substrate Sheets


	
C 1328-05                        Specification for Plastic (Stucco Cement


	
C 1386-07                        Specification for Precast Autoclaved Aerated Concrete (AAC) Wall Construction


	
C 1395/C 1395M-06a              Specification for Gypsum Ceiling Board


	
C 1396M-09a                      Specification for Gypsum Board


	
C 1405-10                        Standard Specification for Glazed Brick (Single Fired, Solid Brick Units


	
C 1492-03 (2009)                  Standard Specification for Concrete Roof


	
C 1629/C 1629M-06                Standard Classification for Abuse-resistant Nondecorated Interior Gypsum Panel Products and Fiber-reinforced Cement Panels


	
C 1658/C 1658M-06                Standard Specification for Glass Mat Gypsum Panels


	
D 25-99 (2005)                  Specification for Round Timber Piles


	
D 41-05 (2010)                  Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing


	
D 43-00 (2006)                  Specification for Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing


	
D 56-05                          Test Method for Flash Point By Tag Closed Tester


	
D 86-10a                          Test Method for Distillation of Petroleum Products at Atmospheric Pressure


	
D 93-10                          Test Method for Flash Point ByPensky-MartensClosed Cup Tester


	
D 225-07                          Specification for Asphalt Shingles (Organic Felt) Surfaced with Mineral Granules


	
D 226/D 226M-09                  Specification for Asphalt-saturated Organic Felt Used in Roofing and Waterproofing


	
D 227-03                          Specification for Coal-tar-saturated Organic Felt Used in Roofing and Waterproofing


	
D 312-00 (2006)                  Specification for Asphalt Used in


	
D 422-63 (2007)                  Test Method for Particle-size Analysis of Soils


	
D 448-08                          Standard Classification for Sizes of Aggregate for Road and Bridge


	
D 450-07                          Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing


	
D 635-10                          Test Method for Rate of Burning and/or Extent and Time of Burning of Self-supporting Plastics in a Horizontal Position


	
D 1143/D 1143M-07e1              Test Method for Piles Under Static Axial Compressive Load


	
D 1227-95 (2007)                  Specification for Emulsified Asphalt Used as a Protective Coating for Roofing


	
D 1557-09                        Test Method for Laboratory Compaction Characteristics of Soil Using Modified Effort [56,000 ft-lb/ft 3 (2,700 KN m/m 3 )]


	
D 1586-08a                      Specification for Penetration Test and Split-barrel Sampling of Soils


	
D 1761-06                        Test Method for Mechanical Fasteners in Wood


	
D 1863-05                        Specification for Mineral Aggregate Used on Built-up Roofs


	
D 1929-96 (2001)e01              Test Method for Determining Ignition Properties of Plastics


	
D 1970-09                        Specification for Self-adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roof Underlayment for Ice Dam Protection


	
D 2166-06                        Test Method for Unconfined Compressive Strength of Cohesive Soil


	
D 2178-04                        Specification for Asphalt Glass Felt Used in Roofing and Waterproofing


	
D 2216-10                        Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass


	
D 2487-10                        Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)


	
D 2626-04                        Specification for Asphalt Saturated and Coated Organic Felt Base Sheet Used in Roofing


	
D 2822-05                        Specification for Asphalt Roof Cement


	
D 2823-05                        Specification for Asphalt Roof Coatings


	
D 2843-10                        Test for Density of Smoke from the Burning or Decomposition of Plastics


	
D 2850-03a (2007)                Test Method for Unconsolidated, Undrained Triaxial Compression Test on Cohesive Soils


	
D 2898-10                        Test Methods for Accelerated Weathering of Fire-retardant-treated Wood for Fire Testing


	
D 3019-08                        Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and NonasbestosFibered


	
D 3161-09                        Test Method for a Wind Resistance of Asphalt Shingles (Fan Induced Method)


	
D 3200-74 (2005)                  Standard Specification and Test Method for Establishing Recommended Design Stresses for Round Timber Construction Poles


	
D 3201-08ae1                      Test Method for Hygroscopic Properties of Fire-retardant-treated Wood and Wood-based Products


	
D 3278-96(2004)e01              Test Methods for Flash Point of Liquids by Small Scale Closed-cup Apparatus


	
D 3462/ D3462M-10a              Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules


	
D 3468-99 (2006)e1              Specification for Liquid-applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing


	
D 3679-09a                      Specification for Rigid Poly [Vinyl Chloride (PVC) Siding]


	
D 3689-07                        Method for Testing Individual Piles Under Static Axial Tensile Load


	
D 3737-09                        Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)


	
D 3746-85 (2008)                  Test Method for Impact Resistance of Bituminous Roofing Systems


	
D 3747-79 (2007)                  Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation


	
D 3909-97b (2004)e01              Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules


	
D 3957-09                        Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings


	
D 4022-07                        Specification for Coal Tar Roof Cement, Asbestos Containing


	
D 4272-09                        Test Method for Total Energy Impact of Plastic Films by Dart Drop


	
D 4318-10                        Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils


	
D 4434/D 4434M-09                Specification for Poly (Vinyl Chloride) Sheet Roofing


	
D 4479-07                        Specification for Asphalt Roof Coatings- Asbestos-free


	
D 4586-07                        Specification for Asphalt Roof Cement-Asbestos-free


	
D 4601-04                        Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing


	
D 4637/D 4637M-10                Specification forEPDMSheet Used in Single-ply Roof Membrane


	
D 4829-08a                      Test Method for Expansion Index of Soils


	
D 4869-05e01                      Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing


	
D 4897/D 4897M-01(2009)          Specification for Asphalt-coated Glass Fiber Venting Base Sheet Used in Roofing


	
D 4945-08                        Test Method for High-strain Dynamic Testing of Piles


	
D 4990-97a (2005)e1              Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing.


	
D 5019-07a                      Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane


	
D 5055-10                        Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists


	
D 5456-10                        Specification for Evaluation of Structural Composite Lumber Products


	
D 5516-09                        Test Method of Evaluating the Flexural Properties of Fire-retardant-treated Softwood Plywood Exposed to the Elevated Temperatures


	
D 5643-06                        Specification for Coal Tar Roof Cement, Asbestos-free


	
D 5664-10                        Test Methods for Evaluating the Effects of Fire-retardant Treatment and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber


	
D 5665-99a (2006)                Specification for Thermoplastic Fabrics Used in Cold-applied Roofing and Waterproofing


	
D 5726-98 (2005)                  Specification for Thermoplastic Fabrics Used in Hot-applied Roofing and Waterproofing .


	
D 6083-05e01                      Specification for Liquid Applied Acrylic Coating Used in Roofing


	
D 6162-00a (2008)                Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements


	
D 6163-00 (2008)                  Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements


	
D 6164-05 e1                      Specification for Styrene-butadiene-styrene (SBS) Modified Bituminous Sheet Metal Materials Using Polyester Reinforcements


	
D 6222-08                        Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements


	
D 6223/D6223M-02(2009)e1          Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements


	
D 6298-05e1                      Specification for Fiberglass Reinforced Styrene-butadiene-styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface


	
D 6305-08                        Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing


	
D 6380-03 (2009)                  Standard Specification for Asphalt Roll Roofing (Organic) Felt


	
D 6509/D6509M-09                  Standard Specification for Atactic Polypropylene (APP) Modified Bituminous base Sheet Materials Using Glass Fiber Reinforcements


	
D 6694-08                        Standard Specification for Liquid-applied Silicone Coating Used in Spray Polyurethane Foam Roofing


	
D 6754/D6754M-10                  Standard Specification for Ketone Ethylene Ester Based Sheet Roofing


	
D 6757-07                        Standard Specification for Inorganic Underlayment for Use with Steep Slope Roofing Products


	
D 6841-08                        Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant-treated Lumber


	
D 6878-08e1                      Standard Specification for ThermoplasticPolyolefinBased Sheet Roofing


	
D 6947-07                        Standard Specification for Liquuid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System


	
D 7158-08d                      Standard Test Method for Wind Resistance of Sealed Asphalt Shingles (Uplift Force/Uplift Resistance Method


	
E 84-10b                          Test Methods for Surface Burning Characteristics of Building Materials


	
E 90-09                          Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements


	
E 96/E 96M-05                    Test Method for Water Vapor Transmission of Materials


	
E 108-10a                        Test Methods for Fire Tests of Roof Coverings


	
E 119-10b                        Test Methods for Fire Tests of Building Construction and Materials


	
E 136-09b                        Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C


	
E 330-02 (2010)                  Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference


	
E 331-00 (2009)                  Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference


	
E 492-09                          Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-ceiling Assemblies Using the Tapping Machine


	
E 605-93 (2006)                  Test Method for Thickness and Density of Sprayed Fire-resistive Material (SFRM) Applied to Structural Members.


	
E 681-09                          Test Methods for Concentration Limits ofFlammabilityof Chemical Vapors and Gases


	
E 736-00 (2006)                  Test Method for Cohesion/Adhesion of Sprayed Fire-resistive Materials Applied to Structural Members


	
E 814-10                          Test Method of Fire Tests of Through-penetration Firestops


	
E 970-10                          Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source


	
E 1300-09a                      Practice for Determining Load Resistance of Glass in Buildings.


	
E 1354-10a                      Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter


	
E 1592-05                        Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference


	
E 1602-03 (2010)e1              Guide for Construction of Solid Fuel-burning Masonry Heaters


	
E 1886-05                        Test Method for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Missiles and Exposed to Cyclic Pressure Differentials


	
E 1966-07                        Test Method for Fire-resistant Joint Systems.


	
E 1996-09                        Specification for Performance of Exterior Windows, Glazed Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes


	
E 2072-10                        Standard Specification for Photoluminescent (Phosphorescent) Safety Markings


	
E 2273-03                        Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies


	
E 2307-10                        Standard Test Method for Determining Fire Resistance of Perimeter Fire Barrier Systems Using Intermediate-scale, Multistory Test Apparatus


	
E 2404-10                        Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Vinyl Wall or Ceiling Coverings to Assess Surface Burning Characteristics


	
E 2568-09e1                      Standard Specification for PB Exterior Insulation and Finish Systems (EIFS)


	
E 2570-07                        Standard Test Method for Evaluating Water-resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) for EIFS with Drainage


	
E 2573-07a                      Standard Practice for Specimen Preparation and Mounting of Site-fabricated Stretch Systems to Assess Surface Burning Characteristics


	
F 547-06                          Terminology of Nails for Use with Wood and Wood-based Materials


	
F 1346-91 (2003)                  Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs


	
F 1667-10                        Specification for Driven Fasteners: Nails, Spikes and Staples


	
F 2006-10                        Standard/Safety Specification for Window Fall Prevention Devices for NonemergencyEscape (Egress) and Rescue (Ingress) Windows


	
F 2090-10                        Specification for Window Fall Prevention Devices with Emergency Escape (Egress) Release Mechanisms


	
F 2200-05                        Standard Specification for Automated Vehicular Gate Construction


	
G 152-06                          Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials


	
G 154-06                          Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials


	
G 155-05a                        Practice for Operating Xenon Arc Light Apparatus for Exposure of Nonmetallic Materials

The Association of the Wall and Ceiling Industries International

513 West Broad Street, Suite 210

Falls Church, VA 22046

 

	
AWCI Standard reference number  Title


	
12-B-05                          Technical Manual 12-B Standard Practice for the Testing and Inspection of Field Applied Thin Film Intumescent Fire-resistive Materials; an Annotated Guide, Second Edition

American Wood Protection Association

P.O. Box 361784

Birmingham, AL 35236-1784

 

	
AWPA Standard reference number  Title


	
C1-03                            All Timber Products-Preservative Treatment by Pressure Processes


	
M4-06                            Standard for the Care of Preservative-treated Wood Products


	
U1-10                            USE CATEGORY SYSTEM: User Specification for Treated Wood Except Section 6, Commodity Specification H

American Welding Society

550 N.W. LeJeune Road

Miami, FL 33126

 

	
AWS Standard reference number  Title


	
D 1.1 -10                      Structural Welding Code-Steel


	
D 1.3 -08                      Structural Welding Code-Sheet Steel


	
D 1.4 -05                      Structural Welding Code-Reinforcing Steel

Builders Hardware Manufacturers’ Association

355 Lexington Avenue, 17th Floor

New York, NY 10017-6603

 

	
BHMA Standard reference number  Title


	
A 156.10 -05                      Power Operated Pedestrian Doors


	
A 156.19 -07                      Standard for Power Assist and Low Energy Operated Doors

Canadian General Standards Board

Place du Portage 111, 6B1

11 Laurier Street

Gatineau, Quebec, Canada KIA 1G6

 

	
CGSB Standard Reference Number  Title


	
37-GP-52M (1984)                  Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric


	
37-GP-56M (1985)                  Membrane, Modified, Bituminous, Prefabricated and Reinforced for Roofing-with December 1985 Amendment


	
CAN/CGSB 37.54 -95              Polyvinyl Chloride Roofing and Waterproofing Membrane

Composite Panel Association

19465 Deerfield Avenue, Suite 306

Leesburg, VA 20176

 

	
CPA Standard reference number  Title


	
ANSI A 135.4 -2004              Basic Hardboard


	
ANSI A 135.5 -2004              Prefinished Hardboard Paneling


	
ANSI A 135.6 -2006              Hardboard Siding

Consumer Product Safety Commission

4330 East West Highway

Bethesda, MD 20814-4408

 

	
CPSC Standard reference number  Title


	
16 CFR Part 1201(1977)          Safety Standard for Architectural Glazing Material


	
16 CFR Part 1209 (1979)          Interim Safety Standard for Cellulose Insulation


	
16 CFR Part 1404 (1979)          Cellulose Insulation


	
16 CFR Part 1500 (1991)          Hazardous Substances and Articles; Administration and Enforcement Regulations


	
16 CFR Part 1500.44(2001)        Method for Determining Extremely Flammable and Flammable Solids


	
16 CFR Part 1507 (2001)          Fireworks Devices


	
16 CFR Part 1630 (2000)          Standard for the Surface Flammability of Carpets and Rugs

Canadian Standards Association

5060 Spectrum Way, Suite 100

Mississauga, Ontario, L4W 5N6 Canada

 

	
CSA Standard reference number  Title


	
101/I.S.2/A440-08              Specifications for Windows, Doors and Unit Skylights

Cedar Shake and Shingle Bureau

P.O. Box 1178

Sumas, WA 98295-1178

 

	
CSSB Standard reference number  Title


	
CSSB-97                          Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau

Door and Access Systems Manufacturers Association International

1300 Summer Avenue

Cleveland, OH 44115-2851

 

	
DASMA Standard reference number  Title


	
ANSI/DASMA 107-1997 (R2004)      Room Fire Test Standard for Garage Doors Using Foam Plastic Insulation


	
108-05                            Standard Method for Testing Sectional Garage Doors and Rolling Doors: Determination of Structural Performance Under Uniform Static Air Pressure Difference


	
115-05                            Standard Method for Testing Sectional Garage Doors and Rolling Doors: Determination of Structural Performance Under Missile Impact and Cyclic Wind Pressure

U.S. Department of Commerce

National Institute of Standards and Technology

1401 Constitution Avenue, NW

Washington, DC 20230

 

	
DOC Standard reference number  Title


	
PS-1-07                          Structural Plywood


	
PS-2-04                          Performance Standard for Wood-based Structural-use Panels


	
PS 20-05                        American Softwood Lumber Standard

U.S. Department of Justice,

950 Pennsylvania Avenue, NW,

Civil Rights Division,

Disability Rights Section-NYA

Washington, DC 20530

 

	
DOJ Standard reference number  Title


	
See Section 3501.3

U.S. Department of Labor

c/o Superintendent of Documents

U.S. Government Printing Office

Washington, DC 20402-9325

 

	
DOL Standard reference number  Title


	
29 CFR Part 1910.1000(1974)      Air Contaminants

U.S. Department of Transportation

c/o Superintendent of Documents

1200 New Jersey Avenue, SE

Washington, DC 20402-9325

 

	
DOTn Standard reference number  Title


	
49CFRParts 100-185-2005          Hazardous Materials Regulations


	
49 CFR Parts 173.137(2005)      Shippers-General Requirements for Shipments and Packaging-Class 8-Assignment of Packing Group


	
49 CFR-1998                      Specification of Transportation of Explosive and Other Dangerous Articles, UN 0335, UN 0336 Shipping Containers

European Committee for Standardization (EN)

Central Secretariat

Rue de Stassart 36

B-10 50 Brussels

 

	
EN Standard reference number  Title


	
EN 1081-98 Resistance          Resilient Floor Coverings-Determination of the Electrical

Federal Emergency Management Agency

Federal Center Plaza

500 C Street S.W.

Washington, DC 20472

 

	
FEMA Standard reference number  Title


	
FIA-TB11-01                      Crawlspace Construction for Buildings Located in Special Flood Hazard Areas

Factory Mutual Global Research

Standards Laboratories Department

1301 Atwood Avenue, P.O. Box 7500

Johnson, RI 02919

 

	
FM Standard reference number  Title


	
4450 (1989)                    Approval Standard for Class 1 Insulated Steel Deck Roofs-with Supplements through July 1992


	
4470 (2010)                    Approval Standard for Class 1 Roof Covers


	
4474 (04)                      Evaluating the Simulated Wind Uplift Resistance of Roof Assemblies Using Static Positive and/or Negative Differential Pressures


	
4880 (2010)                    American National Standard for Evaluating Insulated Wall or Wall and Roof/ Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels, Wall/Ceiling Coating Systems, Interior and Exterior Finish Systems

Gypsum Association

810 First Street N.E. 510

Washington, DC 20002-4268

 

	
GA Standard reference number  Title


	
GA 216-10                      Application and Finishing of Gypsum Panel Products


	
GA 600-09                      Fire-resistance Design Manual, 18th Edition

Hardwood Plywood Veneer Association

1825 Michael Faraday Drive

Reston, VA 20190-5350

 

	
HPVA Standard reference number  Title


	
HP-1-2009                        Standard for Hardwood and Decorative Plywood

U.S. Department of Housing and Urban Development

451 7th Street, SW,

Washington, DC 20410

 

	
HUD Standard reference number                  Title


	
HUD 24 CFR Part 3280 (1994) Safety Standards  Manufactured Home Construction and

International Code Council, Inc.

500 New Jersey Ave, NW 6th Floor

Washington, DC 20001

 

	
ICC Standard reference number  Title


	
ICC/ANSI A 117.1 -03            Accessible and Usable Buildings and Facilities


	
ICC 300-07                      ICC Standard on Bleachers, Folding and Telescopic Seating and


	
ICC 400-07                      Standard on Design and Construction of Log Structures


	
ICC 500-08                      ICC/NSSA Standard on the Design and Construction of Storm


	
ICC 600-08                      Standard for Residential Construction in High Wind Regions


	
IEBC – 09                      International Existing Buildings Code


	
IECC-09                          International Energy Conservation Code (adoption includes only section 101 of chapter 1 and chapters 2 through 6)


	
IFC-09                          International Fire Code


	
IFGC-09                          International Fuel Gas Code (including ICC Emergency Amendment changing IFGC Sections 406.7 )


	
SBCCI SSTD 11-99                Test Standard for Determining Wind Resistance of Concrete or Clay Roof Tiles

International Organization for Standardization

ISO Central Secretariat,

1 ch, de la Voie-Creuse,

Case Postale 56

CH-1211 Geneva 20, Switzerland

 

	
ISO Standard reference number  Title


	
ISO 8115-86                      Cotton Bales-Dimensions and Density

National Association of Architectural Metal Manufacturers,

800 Roosevelt Road,

Bldg. C, Suite 312

Glen Ellyn, IL 60137

 

	
NAAMM Standard reference number  Title


	
FP 1001-07                        Guide Specifications for Design of Metal Flag Poles

National Concrete Masonry Association,

13750 Sunrise Valley,

Herndon, VA 22071-4662

 

	
NCMA Standard reference number  Title


	
TEK5-08                          Details for Concrete Masonry Fire Walls

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02269-9101

 

	
NFPA Standard reference number  Title


	
10-10                            Portable Fire Extinguishers


	
11-10                            Low Expansion Foam


	
12-08                            Carbon Dioxide Extinguishing Systems


	
12A-04                          Halon 1301 Fire Extinguishing Systems


	
13-10                            Installation of Sprinkler Systems (including TIA 10-1)


	
13D-10                          Installation of Sprinkler Systems in One- and Two-family Dwellings and Manufactured Homes


	
13R-10                          Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height


	
14-10                            Installation of Standpipe and Hose System


	
16-07                            Installation of Foam-water Sprinkler and Foam-water Spray Systems


	
17-09                            Dry Chemical Extinguishing Systems


	
17A-09                          Wet Chemical Extinguishing


	
20-10                            Installation of Stationary Pumps for Fire Protection


	
30-08                            Flammable and Combustible Liquids Code


	
31-06                            Installation of Oil-burning Equipment


	
32-07                            Dry Cleaning Plants


	
40-11                            Storage and Handling of Cellulose Nitrate Film


	
58-11                            Liquefied Petroleum Gas Code


	
61-08                            Prevention of Fires and Dust Explosions in Agricultural and Food Product Facilities


	
70-11                            National Electrical Code


	
72-10                            National Fire Alarm Code


	
80-10                            Fire Doors and Other Opening Protectives


	
85-07                            Boiler and Combustion System Hazards Code (Note: NFPA 8503 has been incorporated into NFPA 85)


	
92B-09                          Smoke Management Systems in Malls, Atria and Large Spaces


	
99-05 105-10                      Standard for Health Care Facilities Standard for the Installation of Smoke Door Assemblies


	
110-10                          Emergency and Standby Power Systems


	
111-10                          Stored Electrical Energy Emergency and Standby Power Systems


	
120-10                          Coal Preparation Plants


	
170-09                          Standard for Fire Safety and Emergency Symbols


	
211-10                          Chimneys, Fireplaces, Vents and Solid Fuel-burning


	
252-08                          Standard Methods of Fire Tests of Door Assemblies


	
253-06                          Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source


	
257-07                          Standard for Fire Test for Window and Glass Block Assemblies


	
259-08                          Test Method for Potential Heat of Building Materials


	
265-07                          Method of Fire Tests for Evaluating Room Fire Growth Contribution of Textile Wall Coverings on Full Height Panels and Walls


	
268-07                          Standard Test Method for Determining Ignitibility of Exterior Wall Assemblies Using a Radiant Heat Energy Source


	
285-06                          Standard Method of Test for the Evaluation of Flammability Characteristics of Exterior Nonload-bearingWall Assemblies Containing Combustible Components


	
286-06                          Standard Method of Fire Test for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth


	
288-07                          Standard Method of Fire Tests of Floor Fire Door Assemblies Installed Horizontally in Fire-resistance-rated Floor Systems


	
409-11                          Aircraft Hangars


	
418-06                          Standard for Heliports


	
484-09                          Combustible Metals


	
654-06                          Prevention of Fire & Dust Explosions from the Manufacturing, Processing and Handling of Combustible Particulate Solids


	
655-07                          Prevention of Sulfur Fires and Explosions


	
664-07                          Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities


	
701-10                          Standard Methods of Fire Tests for Flame-propagation of Textiles and Films


	
704-07                          Standard System for the Identification of the Hazards of Materials for Emergency Response


	
1124-06                          Manufacture, Transportation and Storage of Fireworks and Pyrotechnic Articles


	
2001-08                          Clean Agent Fire Extinguishing Systems

Precast Prestressed Concrete Institute

175 W. Jackson Boulevard, Suite 500

Chicago, IL 60604-6938

 

	
PCI Standard reference number  Title


	
MNL 124-89                      Design for Fire Resistance of Precast Prestressed Concrete


	
MNL 128-01                      Recommended Practice for Glass Fiber Reinforced Concrete Panels

Post-Tensioning Institute

8601 North Black Canyon Highway, Suite 103

Phoenix, AZ 85021

 

	
PTI Standard reference number  Title


	
PTI-2008                        Standard Requirements for Analysis of Shallow Concrete Foundations on Expansive Soils, Third Edition


	
PTI-2008                        Standard Requirements for Design of Shallow Post-tensioned Concrete Foundation on Expansive Soils, Second Edition

Rack Manufacturers Institute

8720 Red Oak Boulevard, Suite 201

Charlotte, NC 28217

 

	
RMI Standard reference number  Title


	
ANSI/MH 16.1 -08                Specification for Design, Testing and Utilization of Industrial Steel Storage Racks

Steel Deck Institute,

P. O. Box 25

Fox River Grove, IL 60021

 

	
SDI Standard reference number  Title


	
ANSI/NC 1.0 -06                  Standard for Noncomposite Steel Floor Deck


	
ANSI/RD 1.0 -06                  Standard for Steel Roof Deck

Steel Joist Institute,

1173B London Links Drive

Forest, VA 24551

 

	
SJI Standard reference number  Title


	
CJ- 1.0 -06                      Standard Specification for Composite Steel Joists, CJ-series


	
JG- 1.1 -05                      Standard Specification for Joist Girders


	
K- 1.1 -05                      Standard Specification for Open Web Steel Joists, K- series


	
LH/DLH- 1.1 -05                  Standard Specification for Longspan Steel Joists, LH-series and Deep Longspan Steel Joists, DLH-series

Single-Ply Roofing Institute,

411 Waverly Oaks Road, Suite 331B,

Waltham, MA 02452

 

	
SPRI Standard reference number  Title


	
SPRI/ANSI/ES-1-03                Wind Design Standard for Edge Systems Used with Low Slope Roofing Systems


	
RP-4-02                          Wind Design Guide for Ballasted Single-ply Roofing Systems

Telecommunications Industry Association

2500 Wilson Boulevard

Arlington, VA 22201-3834

 

	
TIA Standard reference number  Title


	
TIA-222-G-09                    Structural Standards for Steel Antenna Towers and Antenna Supporting Structures including-Addendum 1, 222-G-1, Dated 2007

The Masonry Society,

3970 Broadway, Unit 201-D,

Boulder, CO 80304-1135

 

	
TMS Standard reference number  Title


	
0216-07                          Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies


	
0302-07                          Standard Method for Determining the Sound Transmission Class Rating for Masonry Walls


	
402-08                          Building Code Requirements for Masonry Structures


	
602-08                          Specification for Masonry Structures

Truss Plate Institute,

218 N. Lee Street, Suite 312

Alexandria, VA 22314

 

	
TPI Standard reference number  Title


	
TPI 1-2007                      National Design Standards for Metal-plate-connected Wood Truss Construction

Underwriters Laboratories, Inc.

333 Pfingsten Road

Northbrook, IL 60062-2096

 

	
UL Standard reference number  Title


	
9-09                          Fire Tests of Window Assemblies


	
10A-09                          Tin Clad Fire Doors


	
10B-08                          Fire Tests of Door Assemblies


	
10C-09                          Positive Pressure Fire Tests of Door Assemblies


	
14B-08                          Sliding Hardware for Standard Horizontally-mounted Tin Clad Fire Doors


	
14C-06                          Swinging Hardware for Standard Tin Clad Fire Doors Mounted Singly and in Pairs


	
103-10                          Factory-built Chimneys, for Residential Type and Building Heating Appliances


	
127-08                          Factory-built Fireplaces


	
199E-04                        Outline of Investigation for Fire Testing of Sprinklers and Water Spray Nozzles for Protection of Deep Fat Fryers.


	
217-06                          Single and Multiple Station Smoke Alarms


	
263-03                          Standard for Fire Test of Building Construction and Materials


	
268-09                          Smoke Detectors for Fire Protective Signaling Systems


	
300-05                          Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas


	
305-97                          Panic Hardware


	
325-02                          Door, Drapery, Gate, Louver and Window Operations and Systems-with Revisions through February 2006


	
555-2006                      Fire Dampers


	
555C-2006                      Ceiling Dampers


	
555S-99                        Smoke Dampers-with Revisions through July 2006


	
580-2006                      Test for Uplift Resistance of Roof Assemblies


	
641-95                          Type L Low-temperature Venting Systems


	
710B-04                        Recirculating Systems-with Revisions through April 2006


	
723-08                          Standard for Test for Surface Burning Characteristics of Building Materials


	
790-04                          Standard Test Methods for Fire Tests of Roof Coverings


	
793-08                          Standards for Automatically Operated Roof Vents for Smoke and Heat


	
864-03                          Standards for Control Units and Accessories for Fire Alarm Systems-with Revisions through March 2006


	
924-06                          Standard for Safety Emergency Lighting and Power Equipment


	
1040-96                        Fire Test of Insulated Wall Construction-with Revisions through June 2001


	
1256-02                        Fire Test of Roof Deck Construction-with Revisions through January 2007


	
1479-03                        Fire Tests of Through-penetration Firestops-with Revisions through April 2007


	
1482-10                        Solid-fuel-type Room Heater


	
1715-97                        Fire Test of Interior Finish Material-with Revisions through March 2004


	
1777-07                        Chimney Liners


	
1784-01                        Air Leakage Tests of Door Assemblies-with Revisions through December 2004


	
1897-04                        Uplift Tests for Roof Covering Systems


	
1975-06                        Fire Test of Foamed Plastics Used for Decorative Purposes


	
1994-04                        Standard for Luminous Egress Path Marking Systems- with Revisions through February 2005


	
2017-08                        Standards for General-purpose Signaling Devices and Systems


	
2079-04                        Tests for Fire Resistance of Building Joint Systems-with Revisions through March 2006


	
2200-98                        Stationary Engine Generator Assemblies

Underwriters Laboratories of Canada,

7 Underwriters Road,

Toronto, Ontario, Canada M1R3B4

 

	
ULC Standard reference number  Title


	
CAN/ULC S 102.2 -2010          Standard Method of Test for Surface Burning Characteristics of Flooring, Floor Coverings and Miscellaneous Materials and Assemblies-with 2000 Revisions

United States Code,

c/o Superintendent of Documents

U.S. Government Printing Office,

Washington, DC 20402-9325

 

	
USC Standard reference number                                                          Title


	
10 U.S.C. Sections 18233(A)(1) and 10 U.S.C. Sections 18237-199418 USC Part 1, Ch.40  Importation, Manufacture, Distribution and Storage of Explosive Materials

Window and Door Manufacturers Association

1400 East Touhy Avenue 470

Des Plaines, IL 60018

 

	
WDMA Standard reference number    Title


	
AAMA/WDMA/CSA 101/I.S.2/A440-08  Specifications for Windows, Doors and Unit Skylights

Wire Reinforcement Institute, Inc.

942 Main Street, Suite 300

Hartford, CT 06103

 

	
WRI Standard reference number  Title


	
WRI/CRSI-81                      Design of Slab-on-ground Foundations-with 1996 Update

Replaces: 4101:1-35-01

Effective: 11/01/2011 R.C. 119.032 review dates: 11/01/2016 Promulgated Under: 119.03 Statutory Authority: 3781.10(A) Rule Amplifies: 3781.10, 3781.11, 3791.04 Prior Effective Dates: 9/1/92, 2/1/93, 7/1/95, 7/1/97, 3/1/98, 7/1/98, 1/1/99, 12/1/00, 1/1/02, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08, 1/1/09

4101:1-35-01 [Effective 3/15/2012] Referenced standards

3501.1 General. This chapter lists the standards that are referenced in various sections of the building code. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title. The application of the referenced standards shall be as specified in Section 102.5.

3501.2 Referenced codes. When indicated in this code, the following codes refer to provisions in the listed chapters of the administrative code:

 

	
Referenced Code                                                                                                                                                                  Ohio Administrative Code Chapters


	
Building Code Energy Code Fire Code Mechanical Code Ohio Boiler and Pressure Vessel Rules Ohio Elevator Code Residential Code of Ohio for One, Two and Three Family Dwellings  4101:1-1 to 4101:1-35 4101:1-13 1301:7-1 to 1301:7-7 4101:2-1 to 4101:2-15 4101:4-1 to 4101:4-10 4101:5-1 to 4101:5-3 4101:8-1 to 4101:8-44


	
Plumbing Code                                                                                                                                                                  4101:3-1 to 4101:3-13 (These rules apply to all buildings other than one-, two-, and three-family dwellings)


	
Plumbing Code, Ohio (as referenced in the Residential Code of Ohio)                                                                                                              4101:3-1 to 4101:3-13, codified and published as the 2007 Ohio Plumbing Code, effective 7-1-2007 (including updates) through 11-1-2011 (These rules apply only to one-, two-, and three-family dwellings)

3501.3

Building Code Referenced Standards.

Aluminum Association

1525 Wilson Boulevard, Suite 600

Arlington, VA 22209

 

	
AA Standard reference number  Title


	
ADM1-10                        Aluminum Design Manual: Part 1-A Specification for Aluminum Structures, Allowable Stress Design; and Part 1- B-Aluminum Structures, Load and Resistance Factor Design


	
ASM 35-00                      Aluminum Sheet Metal Work in Building Construction (Fourth Edition)

American Architectural Manufacturers Association

1827 Waldon Office

Square, Suite 550

Schaumburg, IL 60173

 

	
AAMA Standard reference number    Title


	
1402-09                          Standard Specifications for Aluminum Siding, Soffit and Fascia


	
AAMA/WDMA/CSA 101/I.S.2/A440-08  North American Fenestration Standard/Specifications for Windows, Doors and Skylights

American Concrete Institute

38800 Country Club Dive

Farmington Hills, MI 48331

 

	
ACI Standard reference number  Title


	
216.1-07                        Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies


	
318-08                          Building Code Requirements for Structural Concrete


	
530-08                          Building Code Requirements for Masonry Structures


	
530.1-08                        Specifications for Masonry Structures

American Forest & Paper Association

1111 19th St, NW Suite 800

Washington, DC 20036

 

	
AF&PA Standard reference number  Title


	
WCD No. 4-03                          Wood Construction Data-Plank and Beam Framing for Residential


	
NDS-05                                National Design Specification (NDS) for Wood Construction with 2005 Supplement


	
AF&PA-93                          Span Tables for Joists and Rafters


	
ANSI/AF&PA PWF-07                  Permanent Wood Foundation Design Specification


	
ANSI/AF&PA SDPWS-08              Special Design Provisions for Wind and Seismic

American Institute of Steel Construction

One East Wacker Drive, Suite 3100

Chicago, IL 60601-2001

 

	
AISC Standard reference number  Title


	
341-05                          Seismic Provisions for Structural Steel Buildings, including Supplement No. 1 dated 2005


	
360-05                          Specification for Structural Steel Buildings

American Iron and Steel Institute

1140 Connecticut Avenue

Suite 705

Washington, DC 20036

 

	
AISI Standard reference number  Title


	
S100-07                          North American Specification for the Design of Cold-formed Steel Structural Members


	
S200-08                          North American Standard for Cold-formed Steel Framing-General


	
S210-08                          North American Standard for Cold-formed Steel Framing-Floor and Roof System Design


	
S211-08                          North American Standard for Cold-formed Steel Framing-Wall Stud


	
S212-08                          North American Standard for Cold-formed Steel Framing-Header Design


	
S213-08                          North American Standard for Cold-formed Steel Framing-Lateral Design


	
S214-08                          North American Standard for Cold-formed Steel Framing-Truss Design, with Supplement 2, dated 2008

American Institute of Timber Construction

Suite 140

7012 S. Revere Parkway

Englewood, CO 80112

 

	
AITC Standard reference number  Title


	
AITC Technical


	
Note 7-96                        Calculation of Fire Resistance of Glued Laminated Timbers


	
AITC 104-03                      Typical Construction Details


	
AITC 110-01                      Standard Appearance Grades for Structural Glued Laminated


	
AITC 113-01                      Standard for Dimensions of Structural Glued Laminated Timber


	
AITC 117-04                      Standard Specifications for Structural Glued Laminated Timber of Softwood Species


	
AITC 119-96                      Standard Specifications for Structural Glued Laminated Timber of Hardwood


	
AITC200-09                      Manufacturing Quality Control Systems Manual for Structural Glued Laminated Timber


	
ANSI/AITCA 190.1-07              Structural Glued Laminated Timber

Automotive Lift Institute

P.O. Box 85

Courtland, NY 13045

 

	
ALI Standard reference number  Title


	
ALI ALCTV-2007                  Standard for Automobile Lifts-Safety Requirements for Construction, Testing and Validation (ANSI)

American National Standards Institute

25 West 43rd Street, Fourth Floor

New York, NY 10036

 

	
ANSI Standard reference number  Title


	
A13.1-07                          Scheme for the Identification of Piping Systems


	
A108.1A-09                      Installation of Ceramic Tile in the Wet-set Method, with      


	
Portland Cement


	
A108.1B-09                      Installation of Ceramic Tile, quarry Tile on a Cured          


	
Portland Cement Mortar Setting Bed with Dry-set or Latex-


	
A108.4-09                        Installation of Ceramic Tile with Organic Adhesives or        


	
Water-cleanable Tile-setting Epoxy Adhesive


	
A108.5-09                        Installation of Ceramic Tile with Dry-set Portland Cement      


	
Mortar or Latex-portland Cement Mortar


	
A108.6-09                        Installation of Ceramic Tile with Chemical-resistant, Water  


	
Cleanable Tile-setting and -grouting Epoxy


	
A108.8-09                        Installation of Ceramic Tile with Chemical-resistant Furan    


	
Resin Mortar and Grout


	
A108.9-09                        Installation of Ceramic Tile with Modified Epoxy              


	
Emulsion Mortar/Grout


	
A108.10-09                      Installation of Grout in Tilework


	
A118.1-10.1                      American National Standard Specifications for Dry-set          


	
Portland Cement


	
A118.3-10.1                      American National Standard Specifications for Chemical-      


	
resistant, Water-cleanable Tile-setting and -grouting Epoxy


	
and Water Cleanable Tile-setting Epoxy


	
A118.4-10.1                      American National Standard Specifications for Latex-          


	
portland Cement


	
A118.5-10.1                      American National Standard Specifications for Chemical        


	
Resistant Furan Mortar and Grouts for Tile


	
A118.8-10.1                      American National Standard Specifications for Modified        


	
Epoxy Emulsion Mortar/Grout


	
A136.1-10.1                      American National Standard Specifications for Organic          


	
Adhesives for Installation of Ceramic


	
137.1-08                          American National Standard Specifications for Ceramic Tile


	
A208.1-09                        Particleboard


	
Z 97.1-09                        Safety Glazing Materials Used in Buildings-Safety              


	
Performance Specifications and Methods of Test

APA – Engineered Wood Association

7011 South 19th

Tacoma, WA 98466

 

	
APA Standard reference number  Title


	
APA PDS-08                      Panel Design Specification


	
APA PDS


	
Supplement 1-90                  Design and Fabrication of Plywood Curved Panels (revised  


	
1995)


	
APA PDS


	
Supplement 2-92                  Design and Fabrication of Plywood-lumber Beams (revised    


	
1998


	
APA PDS


	
Supplement 3-96                  Design and Fabrication of Plywood Stressed-skin Panels      


	
(revised 1996


	
APA PDS


	
Supplement 4-93                  Design and Fabrication of Plywood Sandwich Panels          


	
(revised 1993)


	
APA PDS


	
Supplement 5-95                  Design and Fabrication of All-plywood Beams (revised      


	
1995


	
EWS R540-07                      Builders Tips: Proper Storage and Handling of Glulam      


	
Beams


	
EWS S475-07                      Glued Laminated Beam Design Tables


	
EWS S560-10                      Field Notching and Drilling of Glued Laminated Timber      


	
Beams


	
EWS T300-07                      Glulam Connection


	
EWS X440-08                      Product Guide- Glulam


	
EWS X450-01                      Glulam in Residential Construction-Western Edition

The Association of Pool & Spa Professionals

2111 Eisenhower Avenue

Alexandria, VA 22314

 

	
APSP Standard reference number  Title


	
ANSI/APSP 7-06                  Standard for Suction Entrapment Avoidance in Swimming Pools, Wading Pools, Spas, Hot Tubs and Catch Basins

American Society of Agricultural and Biological Engineers

2950 Niles Road

St. Joseph, MI 49085

 

	
ASABE Standard reference number  Title


	
EP 484.2 -98                      Diaphragm Design of Metal-clad, Post-frame Rectangular  


	
Buildings


	
EP 486.1 -99                      Shallow-post Foundation Design


	
EP 559 -03                        Design Requirements and Bending Properties for          


	
Mechanically Laminated Columns

American Society of Civil Engineers

Structural Engineering Institute

1801 Alexander Bell Drive

Reston, VA 20191-4400

 

	
ASCE/SEI Standard reference number  Title


	
3-91                                  Structural Design of Composite Slabs


	
5-08                                  Building Code Requirements for Masonry


	
6-08                                  Specification for Masonry Structures


	
7-05                                  Minimum Design Loads for Buildings and Other Structures          


	
including Supplements No. 1 and 2, excluding Chapter 14 and


	
Appendix 11A


	
8-02                                  Standard Specification for the Design of Cold-formed Stainless  


	
Steel Structural Members


	
19-10                                Structural Applications of Steel Cables for Buildings


	
24-05                                Flood Resistant Design and Construction


	
29-05                                Standard Calculation Methods for Structural Fire Protection


	
32-01                                Design and Construction of Frost Protected Shallow Foundations

American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.

1791 Tullie Circle, NE

Atlanta, GA 30329-2305

 

	
ASHRAE Standard Reference Number  Title


	
ASHRAE 90.1-2007                  Energy Standard for Buildings Except Low-Rise Buildings

American Society of Mechanical Engineers

Three Park Avenue

New York, NY 10016-5990

 

	
ASME Standard reference number  Title


	
A17.1/CSA B44- 2010              Safety Code for Elevators and Escalators


	
A18.1-2008                      Safety Standard for Platform Lifts and Stairway    


	
Chairlifts


	
A90.1- 2009                      Safety Standard for Belt Manlifts


	
B16.18-2001


	
(Reaffirmed 2005)                Cast Copper Alloy Solder Joint Pressure Fittings


	
B16.22-2001


	
(Reaffirmed 2005)                Wrought Copper and Copper Alloy Solder Joint      


	
Pressure Fittings


	
B20.1-2009                      Safety Standard for Conveyors and Related          


	
Equipment


	
B31.3-2008                      Process Piping

ASTM International

100 Barr Harbor Drive

West Conshohocken, PA 19428-2959

 

	
ASTM Standard reference number  Title


	
A 36/A 36M-08                    Specification for Carbon Structural Steel


	
A 153/A 153M-09                  Specification for Zinc Coating (Hot-dip) on Iron          


	
and Steel Hardware


	
A 240/A 240M-10a                  Standard Specification for Chromium and                    


	
Chromium-nickel Stainless Steel Plate,


	
Sheet and Strip for Pressure Vessels and for


	
General Applications


	
A 252-10                          Specification for Welded and Seamless Steel Pipe          


	
Piles


	
A 283/A 283M-03(2007)            Specification for Low and Intermediate Tensile              


	
Strength Carbon Steel Plates


	
A 307-07b                        Specification for Carbon Steel Bolts and Studs,            


	
60,000 psi Tensile Strength


	
A 416/A 416M-10                  Specification for Steel Strand, Uncoated Seven-wire        


	
for Prestressed Concrete


	
A 463/A 463M-09a                  Standard Specification for Steel Sheet, Aluminum-          


	
coated, by the Hot-dip Process


	
A 572/A 572M-07                  Specification for High-strength Low-alloy                  


	
Columbium-vanadium Structural Steel


	
A 588/A 588M-10                  Specification for High-strength Low-alloy                  


	
Structural Steel with 50 ksi (345 MPa)


	
Minimum Yield Point to 4 inches (100 mm) Thick


	
A 615/A 615M-09b                  Specification for Deformed and Plain Billet-steel          


	
Bars for Concrete Reinforcement


	
A 653/A 653M-09a                  Specification for Steel Sheet, Zinc-coated                  


	
Galvanized or Zinc-iron Alloy-coated


	
Galvannealed by the Hot-dip Process


	
A 690/A 690M-07                  Standard Specification for High-strength Low-alloy          


	
Nickel, Copper, Phosphorus Steel H-piles and


	
Sheet Piling with Atmospheric Corrosion


	
Resistance for Use in Marine Environments


	
A 706/A 706M-09b                  Specification for Low-alloy Steel Deformed and              


	
Plain Bars for


	
Concrete Reinforcement


	
A 722/A 722M-07                  Specification for Uncoated High-strength Steel Bar          


	
for Prestressing


	
A 755/A 755M-03(2008)            Specification for Steel Sheet, Metallic-coated by the      


	
Hot-dip Process and Prepainted by the


	
Coil-coating Process for Exterior Exposed Building


	
Products


	
A 792/A 792M-09a                  Specification for Steel Sheet, 55% Aluminum-zinc          


	
Alloy-coated by the Hot-dip Process


	
A 875/A 875M-09a                  Standard Specification for Steel Sheet Zinc-5              


	
percent, Aluminum Alloy-coated by the Hot-dip


	
Process


	
A 913/A 913M-07                  Specification for High-strength Low-alloy Steel            


	
Shapes of Structural Quality, Produced by


	
Quenching and Self-tempering Process (QST)


	
A 924/A 924M-10                  Standard Specification for General Requirements            


	
for Steel Sheet, Metallic-coated by the Hot-dip


	
Process


	
A 992/A 992M-06a                  Standard Specification for Structural Shapes


	
B 42-10                          Specification for Seamless Copper Pipe, Standard


	
B 43-09                          Specification for Seamless Red Brass Pipe,                  


	
Standard Sizes


	
B 68-02                          Specification for Seamless Copper Tube, Bright              


	
Annealed (Metric


	
B 88-09                          Specification for Seamless Copper Water Tube


	
B 101-07                          Specification for Lead-coated Copper Sheet and              


	
Strip for Building Construction


	
B 209-07                          Specification for Aluminum and Aluminum Alloy              


	
Steel and Plate


	
B 251-10                          Specification for General Requirements for                  


	
Wrought Seamless Copper and Copper-alloy Tube


	
B 280-08                          Specification for Seamless Copper Tube for Air              


	
Conditioning and Refrigeration Field Service


	
B 370-09                          Specification for Cold-rolled Copper Sheet and              


	
Strip for Building Construction


	
B 695-04(2009)                  Standard Specification for Coatings of Zinc                


	
Mechanically Deposited on Iron and Steel


	
C 5-10                          Specification for Quicklime for Structural


	
C 22/C 22M-00 (2005)e01          Specification for Gypsum


	
C 27-98 (2008)                  Specification for Standard Classification of Fireclay      


	
and High-alumina Refractory Brick


	
C 28/C 28M-10                    Specification for Gypsum


	
C 31/C 31M-10                    Practice for Making and Curing Concrete Test              


	
Specimens in the Field


	
C 33-08                          Specification for Concrete Aggregates


	
C 34-10                          Specification for Structural Clay Load-bearing Wall Tile


	
C 35-01(2009)                    Specification for Inorganic Aggregates for Use in          


	
Gypsum Plaster


	
C 36/C 36M-03                    Specification for Gypsum Wallboard


	
C 37/C 37M-01                    Specification for Gypsum Lath


	
C 55-09                          Specification for Concrete Building Brick


	
C 56-10                          Specification for Structural Clay Nonload Bearing          


	
Tile


	
C 59/C 59M-00 (2006)              Specification for Gypsum Casting and Molding              


	
Plaster


	
C 61/C 61M-00 (2006)              Specification for Gypsum Keene’s


	
C 62-10                          Specification for Building Brick (Solid Masonry            


	
Units Made from Clay or Shale


	
C 67-09                          Test Methods of Sampling and Testing Brick and              


	
Structural Clay


	
C 73-05                          Specification for Calcium Silicate Face Brick              


	
(Sand-lime Brick)


	
C 79-04a                          Specification for Treated Core and Nontreated Core          


	
Gypsum Sheathing Board


	
C 90-09                          Specification for Loadbearing Concrete Masonry              


	
Units


	
C 91-05                          Specification for Masonry Cement


	
C 94/C 94M-10                    Specification for Ready-mixed


	
C 126-10                          Specification for Ceramic Glazed Structural Clay          


	
Facing Tile, Facing Brick and Solid Masonry Units


	
C 140-10                          Test Method Sampling and Testing Concrete                  


	
Masonry Units and Related Units


	
C 150-09                          Specification for Portland Cement


	
C 172-10                          Practice for Sampling Freshly Mixed


	
C 199-84 (2005)                  Test Method for Pier Test for Refractory Mortars


	
C 206-03 (2009)                  Specification for Finishing Hydrated Lime


	
C 208-08a                        Specification for Cellulosic Fiber Insulating Board


	
C 212-10                          Specification for Structural Clay Facing Tile


	
C 216-10                          Specification for Facing Brick (Solid Masonry              


	
Units Made from Clay or Shale


	
C 270-10                          Specification for Mortar for Unit Masonry


	
C 315-07                          Specification for Clay Flue Liners and Chimney Pots


	
C 317/C 317M-00 (2005)          Specification for Gypsum Concrete


	
C 330-09                          Specification for Lightweight Aggregates for              


	
Structural Concrete


	
C 331-05                          Specification for Lightweight Aggregates for              


	
Concrete Masonry Units


	
C 406-10                          Specification for Roofing Slate


	
C 442/C 442M-04                  Specification for Gypsum Backing Board and                  


	
Coreboard and Gypsum Shaftliner Board


	
C 472-99 (2009)                  Specification for Standard Test Methods for                


	
Physical Testing of Gypsum, Gypsum Plasters and


	
Gypsum Concrete


	
C 473-10                          Test Method for Physical Testing of Gypsum Panel          


	
Products


	
C 474-05                          Test Methods for Joint Treatment Materials for              


	
Gypsum Board Construction


	
C 475-02 (2007)                  Specification for Joint Compound and Joint Tape            


	
for Finishing Gypsum Wallboard


	
C 503-10                          Specification for Marble Dimension Stone (Exterior


	
C 514-04 (2009)e1                Specification for Nails for the Application of              


	
Gypsum


	
C 516-08                          Specifications for Vermiculite Loose Fill Thermal


	
C 547-07e1                      Specification for Mineral Fiber Pipe Insulation


	
C 549-06                          Specification for Perlite Loose Fill


	
C 552-07                          Standard Specification for Cellular Glass Thermal          


	
Insulation


	
C 557-03(2009)e01                Specification for Adhesives for Fastening Gypsum          


	
Wallboard to Wood Framing


	
C 568-10                          Specification for Limestone Dimension Stone


	
C 578-10                          Standard Specification for Rigid, Cellular                  


	
Polystyrene Thermal Insulation


	
C 587-04 (2009)                  Specification for Gypsum Veneer Plaster


	
C 588/C 588M-01                  Specification for Gypsum Base for Veneer Plasters


	
C 595-10                          Specification for Blended Hydraulic Cements


	
C 615-10                          Specification for Granite Dimension


	
C 616-10                          Specification for Quartz Dimension Stone


	
C 629-10                          Specification for Slate Dimension


	
C 630/C 630M-03                  Specification for Water-resistant Gypsum Backing          


	
Board


	
C 631-09                          Specification for Bonding Compounds for Interior          


	
Gypsum Plastering


	
C 635/C 635M-07                  Specification for the Manufacture, Performance and          


	
Testing of Metal Suspension Systems for Acoustical


	
Tile and Lay-in Panel


	
C 636/C 636M-08                  Practice for Installation of Metal Ceiling                  


	
Suspension Systems for Acoustical Tile and Lay-in


	
Panels


	
C 645-09a                        Specification for Nonstructural Steel Framing              


	
Members


	
C 652-10                          Specification for Hollow Brick (Hollow Masonry              


	
Units Made from Clay or Shale


	
C 728-05 (2010)                  Standard Specification for Perlite Thermal Insulation      


	
Board


	
C 744-10                          Specification for Prefaced Concrete and Calcium            


	
Silicate Masonry


	
C 754-09a                        Specification for Installation of Steel Framing            


	
Members to Receive Screw-attached Gypsum Panel


	
Products


	
C 836/C 836M-10                  Specification for High-solids Content, Cold Liquid-        


	
applied Elastomeric Waterproofing Membrane for


	
Use with Separate Wearing Course


	
C 840-08                          Specification for Application and Finishing of              


	
Gypsum Board


	
C 841-03 (2008)e1                Specification for Installation of Interior Lathing and      


	
Furring


	
C 842-05                          Specification for Application of Interior Gypsum          


	
Plaster


	
C 843-99 (2006)                  Specification for Application of Gypsum Veneer              


	
Plaster


	
C 844-10                          Specification for Application of Gypsum Base to            


	
Receive Gypsum Veneer Plaster


	
C 847-10a                        Specification for Metal Lath


	
C 887-05 (2010)                  Specification for Packaged, Dry Combined                  


	
Materials for Surface Bonding Mortar


	
C 897-05 (2009)                  Specification for Aggregate for Job-mixed Portland          


	
Cement-based Plaster


	
C 920-10                          Standard for Specification for Elastomeric Joint          


	
Sealants


	
C 926-06                          Specification for Application of Portland Cement-          


	
based Plaster


	
C 931/C 931M-04                  Specification for Exterior Gypsum Soffit Board


	
C 932-06                          Specification for Surface-applied Bonding                  


	
Compounds Agents for Exterior Plastering


	
C 933-09                          Specification for Welded Wire Lath


	
C 946-10                          Specification for Practice for Construction of Dry-        


	
stacked, Surface-bonded Walls


	
C 954-10                          Specification for Steel Drill Screws for the              


	
Application of Gypsum Panel Products or Metal


	
Plaster Bases to Steel Studs from 0.033 inch (0.84


	
mm) to 0.112 inch (2.84 mm) in Thickness


	
C 955-09a                        Standard Specification for Load-bearing Transverse          


	
and Axial Steel Studs, Runners Tracks, and Bracing


	
or Bridging, for Screw Application of Gypsum


	
Panel Products and Metal Plaster Bases


	
C 956-04 (2010)                  Specification for Installation of Cast-in-place            


	
Reinforced Gypsum


	
C 957-10                          Specification for High-solids Content, Cold Liquid-        


	
applied Elastomeric Waterproofing Membrane with


	
Integral Wearing Surface


	
C 960-04                          Specification for Predecorated Gypsum Board


	
C 1002-07                        Specification for Steel Self-piercing Tapping              


	
Screws for the Application of Gypsum Panel


	
Products or Metal Plaster Bases to Wood Studs or


	
Steel Studs


	
C 1007-08a                      Specification for Installation of Load Bearing              


	
(Transverse and Axial) Steel Studs and Related


	
Accessories


	
C 1019-09                        Test Method of Sampling and Testing Grout


	
C 1029-10                        Specification for Spray-applied Rigid Cellular              


	
Polyurethane Thermal Insulation


	
C 1032-06                        Specification for Woven Wire Plaster Base


	
C 1047-10a                      Specification for Accessories for Gypsum                  


	
Wallboard and Gypsum Veneer


	
C 1063-08                        Specification for Installation of Lathing and Furring      


	
to Receive Interior and Exterior Portland Cement-


	
based Plaster


	
C 1088-10                        Specification for Thin Veneer Brick Units Made              


	
from Clay or Shale


	
C 1167-03 (2009)                  Specification for Clay Roof Tiles


	
C 1177/C 1177M-08                Specification for Glass Mat Gypsum Substrate for          


	
Use as Sheathing


	
C 1178/C 1178M-08                Specification for Coated Glass Mat Water-resistant          


	
Gypsum Backing Panel


	
C 1186-08                        Specification for Flat-Fiber Cement Sheets


	
C 1261-10                        Specification for Firebox Brick for Residential            


	
Fireplaces


	
C 1278/C 1278M-07a              Specification for Fiber-reinforced Gypsum Panels


	
C 1280-09                        Specification for Application of Gypsum Sheathing


	
C 1283-07a                      Practice for Installing Clay Flue Lining.


	
C 1288-99 (2010)                  Standard Specification for Discrete Nonasbestos            


	
Fiber-cement Interior Substrate Sheets


	
C 1289-10                        Standard Specification for Faced Rigid Cellular            


	
Polyisocyanurate Thermal Insulation Board


	
C 1314-10                        Test Method for Compressive Strength of Masonry            


	
Prisms


	
C 1325-08b                      Standard Specification for Nonasbestos Fiber-mat          


	
Reinforced Cement Interior Substrate Sheets


	
C 1328-05                        Specification for Plastic (Stucco Cement


	
C 1386-07                        Specification for Precast Autoclaved Aerated              


	
Concrete (AAC) Wall Construction


	
C 1395/C 1395M-06a              Specification for Gypsum Ceiling Board


	
C 1396M-09a                      Specification for Gypsum Board


	
C 1405-10                        Standard Specification for Glazed Brick (Single            


	
Fired, Solid Brick Units


	
C 1492-03 (2009)                  Standard Specification for Concrete Roof


	
C 1629/C 1629M-06                Standard Classification for Abuse-resistant                


	
Nondecorated Interior Gypsum Panel Products and


	
Fiber-reinforced Cement Panels


	
C 1658/C 1658M-06                Standard Specification for Glass Mat Gypsum                


	
Panels


	
D 25-99 (2005)                  Specification for Round Timber Piles


	
D 41-05 (2010)                  Specification for Asphalt Primer Used in Roofing,          


	
Dampproofing and Waterproofing


	
D 43-00 (2006)                  Specification for Coal Tar Primer Used in Roofing,          


	
Dampproofing and Waterproofing


	
D 56-05                          Test Method for Flash Point By Tag Closed Tester


	
D 86-10a                          Test Method for Distillation of Petroleum Products          


	
at Atmospheric Pressure


	
D 93-10                          Test Method for Flash Point By Pensky-                      


	
Martens Closed Cup Tester


	
D 225-07                          Specification for Asphalt Shingles (Organic Felt)          


	
Surfaced with Mineral Granules


	
D 226/D 226M-09                  Specification for Asphalt-saturated Organic Felt          


	
Used in Roofing and Waterproofing


	
D 227-03                          Specification for Coal-tar-saturated Organic Felt          


	
Used in Roofing and Waterproofing


	
D 312-00 (2006)                  Specification for Asphalt Used in


	
D 422-63 (2007)                  Test Method for Particle-size Analysis of Soils


	
D 448-08                          Standard Classification for Sizes of Aggregate for          


	
Road and Bridge


	
D 450-07                          Specification for Coal-tar Pitch Used in Roofing,          


	
Dampproofing and Waterproofing


	
D 635-10                          Test Method for Rate of Burning and/or Extent and          


	
Time of Burning of Self-supporting Plastics in a


	
Horizontal Position


	
D 1143/D 1143M-07e1              Test Method for Piles Under Static Axial                  


	
Compressive Load


	
D 1227-95 (2007)                  Specification for Emulsified Asphalt Used as a              


	
Protective Coating for Roofing


	
D 1557-09                        Test Method for Laboratory Compaction                      


	
Characteristics of Soil Using Modified Effort


	
[56,000 ft-lb/ft 3 (2,700 KN m/m 3 )]


	
D 1586-08a                      Specification for Penetration Test and Split-barrel        


	
Sampling of Soils


	
D 1761-06                        Test Method for Mechanical Fasteners in Wood


	
D 1863-05                        Specification for Mineral Aggregate Used on Built-          


	
up Roofs


	
D 1929-96 (2001)e01              Test Method for Determining Ignition Properties of          


	
Plastics


	
D 1970-09                        Specification for Self-adhering Polymer Modified          


	
Bituminous Sheet Materials Used as Steep Roof


	
Underlayment for Ice Dam Protection


	
D 2166-06                        Test Method for Unconfined Compressive Strength            


	
of Cohesive Soil


	
D 2178-04                        Specification for Asphalt Glass Felt Used in              


	
Roofing and Waterproofing


	
D 2216-10                        Test Method for Laboratory Determination of Water          


	
(Moisture) Content of Soil and Rock by Mass


	
D 2487-10                        Practice for Classification of Soils for Engineering      


	
Purposes (Unified Soil Classification System)


	
D 2626-04                        Specification for Asphalt Saturated and Coated              


	
Organic Felt Base Sheet Used in Roofing


	
D 2822-05                        Specification for Asphalt Roof Cement


	
D 2823-05                        Specification for Asphalt Roof Coatings


	
D 2843-10                        Test for Density of Smoke from the Burning or              


	
Decomposition of Plastics


	
D 2850-03a (2007)                Test Method for Unconsolidated, Undrained                  


	
Triaxial Compression Test on Cohesive Soils


	
D 2898-10                        Test Methods for Accelerated Weathering of Fire-          


	
retardant-treated Wood for Fire Testing


	
D 3019-08                        Specification for Lap Cement Used with Asphalt              


	
Roll Roofing, Nonfibered, Asbestos Fibered and


	
Nonasbestos Fibered


	
D 3161-09                        Test Method for a Wind Resistance of Asphalt              


	
Shingles (Fan Induced Method)


	
D 3200-74 (2005)                  Standard Specification and Test Method for                  


	
Establishing Recommended Design Stresses for


	
Round Timber Construction Poles


	
D 3201-08ae1                      Test Method for Hygroscopic Properties of Fire-            


	
retardant-treated Wood and Wood-based Products


	
D 3278-96(2004)e01              Test Methods for Flash Point of Liquids by Small          


	
Scale Closed-cup Apparatus


	
D 3462/ D3462M-10a              Specification for Asphalt Shingles Made from Glass          


	
Felt and Surfaced with Mineral Granules


	
D 3468-99 (2006)e1              Specification for Liquid-applied Neoprene and              


	
Chlorosulfonated Polyethylene Used in Roofing and


	
Waterproofing


	
D 3679-09a                      Specification for Rigid Poly [Vinyl Chloride (PVC)          


	
Siding]


	
D 3689-07                        Method for Testing Individual Piles Under Static          


	
Axial Tensile Load


	
D 3737-09                        Practice for Establishing Allowable Properties for          


	
Structural Glued Laminated Timber (Glulam)


	
D 3746-85 (2008)                  Test Method for Impact Resistance of Bituminous            


	
Roofing Systems


	
D 3747-79 (2007)                  Specification for Emulsified Asphalt Adhesive for          


	
Adhering Roof Insulation


	
D 3909-97b (2004)e01              Specification for Asphalt Roll Roofing (Glass Felt)        


	
Surfaced with Mineral Granules


	
D 3957-09                        Standard Practices for Establishing Stress Grades          


	
for Structural Members Used in Log Buildings


	
D 4022-07                        Specification for Coal Tar Roof Cement, Asbestos          


	
Containing


	
D 4272-09                        Test Method for Total Energy Impact of Plastic              


	
Films by Dart Drop


	
D 4318-10                        Test Methods for Liquid Limit, Plastic Limit and          


	
Plasticity Index of Soils


	
D 4434/D 4434M-09                Specification for Poly (Vinyl Chloride) Sheet              


	
Roofing


	
D 4479-07                        Specification for Asphalt Roof Coatings-                  


	
Asbestos-free


	
D 4586-07                        Specification for Asphalt Roof Cement-Asbestos-free


	
D 4601-04                        Specification for Asphalt-coated Glass Fiber Base          


	
Sheet Used in Roofing


	
D 4637/D 4637M-10                Specification for EPDM Sheet Used in Single-ply            


	
Roof Membrane


	
D 4829-08a                      Test Method for Expansion Index of Soils


	
D 4869-05e01                      Specification for Asphalt-saturated (Organic Felt)          


	
Underlayment Used in Steep Slope Roofing


	
D 4897/D 4897M-01(2009)          Specification for Asphalt-coated Glass Fiber              


	
Venting Base Sheet Used in Roofing


	
D 4945-08                        Test Method for High-strain Dynamic Testing of              


	
Piles


	
D 4990-97a (2005)e1              Specification for Coal Tar Glass Felt Used in              


	
Roofing and Waterproofing.


	
D 5019-07a                      Specification for Reinforced Nonvulcanized                  


	
Polymeric Sheet Used in Roofing Membrane


	
D 5055-10                        Specification for Establishing and Monitoring              


	
Structural Capacities of Prefabricated Wood I-joists


	
D 5456-10                        Specification for Evaluation of Structural                  


	
Composite Lumber Products


	
D 5516-09                        Test Method of Evaluating the Flexural Properties          


	
of Fire-retardant-treated Softwood Plywood


	
Exposed to the Elevated Temperatures


	
D 5643-06                        Specification for Coal Tar Roof Cement, Asbestos-free


	
D 5664-10                        Test Methods for Evaluating the Effects of Fire-          


	
retardant Treatment and Elevated Temperatures on


	
Strength Properties of Fire-retardant-treated Lumber


	
D 5665-99a (2006)                Specification for Thermoplastic Fabrics Used in            


	
Cold-applied Roofing and Waterproofing


	
D 5726-98 (2005)                  Specification for Thermoplastic Fabrics Used in            


	
Hot-applied Roofing and Waterproofing .


	
D 6083-05e01                      Specification for Liquid Applied Acrylic Coating          


	
Used in Roofing


	
D 6162-00a (2008)                Specification for Styrene-butadiene-styrene (SBS)          


	
Modified Bituminous Sheet Materials Using a


	
Combination of Polyester and Glass Fiber


	
Reinforcements


	
D 6163-00 (2008)                  Specification for Styrene-butadiene-styrene (SBS)          


	
Modified Bituminous Sheet Materials Using Glass


	
Fiber Reinforcements


	
D 6164-05 e1                      Specification for Styrene-butadiene-styrene (SBS)          


	
Modified Bituminous Sheet Metal Materials Using


	
Polyester Reinforcements


	
D 6222-08                        Specification for Atactic Polypropylene (APP)              


	
Modified Bituminous Sheet Materials Using


	
Polyester Reinforcements


	
D 6223/D6223M-02(2009)e1          Specification for Atactic Polypropylene (APP)              


	
Modified Bituminous Sheet Materials Using a


	
Combination of Polyester and Glass Fiber


	
Reinforcements


	
D 6298-05e1                      Specification for Fiberglass Reinforced Styrene-          


	
butadiene-styrene (SBS) Modified Bituminous


	
Sheets with a Factory Applied Metal Surface


	
D 6305-08                        Practice for Calculating Bending Strength Design          


	
Adjustment Factors for Fire-retardant-treated


	
Plywood Roof Sheathing


	
D 6380-03 (2009)                  Standard Specification for Asphalt Roll Roofing            


	
(Organic) Felt


	
D 6509/D6509M-09                  Standard Specification for Atactic Polypropylene          


	
(APP) Modified Bituminous base Sheet Materials


	
Using Glass Fiber Reinforcements


	
D 6694-08                        Standard Specification for Liquid-applied Silicone          


	
Coating Used in Spray Polyurethane Foam Roofing


	
D 6754/D6754M-10                  Standard Specification for Ketone Ethylene Ester          


	
Based Sheet Roofing


	
D 6757-07                        Standard Specification for Inorganic Underlayment          


	
for Use with Steep Slope Roofing Products


	
D 6841-08                        Standard Practice for Calculating Design Value              


	
Treatment Adjustment Factors for Fire-retardant-


	
treated Lumber


	
D 6878-08e1                      Standard Specification for                                  


	
Thermoplastic Polyolefin Based Sheet Roofing


	
D 6947-07                        Standard Specification for Liquuid Applied                  


	
Moisture Cured Polyurethane Coating Used in


	
Spray Polyurethane Foam Roofing System


	
D 7158-08d                      Standard Test Method for Wind Resistance of                


	
Sealed Asphalt Shingles (Uplift Force/Uplift


	
Resistance Method


	
E 84-10b                          Test Methods for Surface Burning Characteristics of        


	
Building Materials


	
E 90-09                          Test Method for Laboratory Measurement of                  


	
Airborne Sound Transmission Loss of Building


	
Partitions and Elements


	
E 96/E 96M-05                    Test Method for Water Vapor Transmission of                


	
Materials


	
E 108-10a                        Test Methods for Fire Tests of Roof Coverings


	
E 119-10b                        Test Methods for Fire Tests of Building                    


	
Construction and Materials


	
E 136-09b                        Test Method for Behavior of Materials in a Vertical        


	
Tube Furnace at 750°C


	
E 330-02 (2010)                  Test Method for Structural Performance of Exterior          


	
Windows, Curtain Walls and Doors by Uniform


	
Static Air Pressure Difference


	
E 331-00 (2009)                  Test Method for Water Penetration of Exterior              


	
Windows, Skylights, Doors and Curtain Walls by


	
Uniform Static Air Pressure Difference


	
E 492-09                          Test Method for Laboratory Measurement of Impact          


	
Sound Transmission Through Floor-ceiling


	
Assemblies Using the Tapping Machine


	
E 605-93 (2006)                  Test Method for Thickness and Density of Sprayed          


	
Fire-resistive Material (SFRM) Applied to


	
Structural Members.


	
E 681-09                          Test Methods for Concentration Limits                      


	
of Flammability of Chemical Vapors and Gases


	
E 736-00 (2006)                  Test Method for Cohesion/Adhesion of Sprayed              


	
Fire-resistive Materials Applied to Structural


	
Members


	
E 814-10                          Test Method of Fire Tests of Through-penetration          


	
Firestops


	
E 970-10                          Test Method for Critical Radiant Flux of Exposed          


	
Attic Floor Insulation Using a Radiant Heat Energy


	
Source


	
E 1300-09a                      Practice for Determining Load Resistance of Glass          


	
in Buildings.


	
E 1354-10a                      Standard Test Method for Heat and Visible Smoke            


	
Release Rates for Materials and Products Using an


	
Oxygen Consumption Calorimeter


	
E 1592-05                        Test Method for Structural Performance of Sheet            


	
Metal Roof and Siding Systems by Uniform Static


	
Air Pressure Difference


	
E 1602-03 (2010)e1              Guide for Construction of Solid Fuel-burning              


	
Masonry Heaters


	
E 1886-05                        Test Method for Performance of Exterior Windows,          


	
Curtain Walls, Doors and Storm Shutters Impacted


	
by Missiles and Exposed to Cyclic Pressure


	
Differentials


	
E 1966-07                        Test Method for Fire-resistant Joint Systems.


	
E 1996-09                        Specification for Performance of Exterior Windows,          


	
Glazed Curtain Walls, Doors and Impact Protective


	
Systems Impacted by Windborne Debris in


	
Hurricanes


	
E 2072-10                        Standard Specification for Photoluminescent                


	
(Phosphorescent) Safety Markings


	
E 2273-03                        Standard Test Method for Determining the Drainage          


	
Efficiency of Exterior Insulation and Finish


	
Systems (EIFS) Clad Wall Assemblies


	
E 2307-10                        Standard Test Method for Determining Fire                  


	
Resistance of Perimeter Fire Barrier Systems Using


	
Intermediate-scale, Multistory Test Apparatus


	
E 2404-10                        Standard Practice for Specimen Preparation and              


	
Mounting of Textile, Paper or Vinyl Wall or Ceiling


	
Coverings to Assess Surface Burning


	
Characteristics


	
E 2568-09e1                      Standard Specification for PB Exterior Insulation          


	
and Finish Systems (EIFS)


	
E 2570-07                        Standard Test Method for Evaluating Water-                  


	
resistive Barrier (WRB) Coatings Used Under


	
Exterior Insulation and Finish Systems (EIFS) for


	
EIFS with Drainage


	
E 2573-07a                      Standard Practice for Specimen Preparation and              


	
Mounting of Site-fabricated Stretch Systems to


	
Assess Surface Burning Characteristics


	
F 547-06                          Terminology of Nails for Use with Wood and                  


	
Wood-based Materials


	
F 1346-91 (2003)                  Performance Specification for Safety Covers and            


	
Labeling Requirements for All Covers for


	
Swimming Pools, Spas and Hot Tubs


	
F 1667-10                        Specification for Driven Fasteners: Nails, Spikes          


	
and Staples


	
F 2006-10                        Standard/Safety Specification for Window Fall              


	
Prevention Devices for NonemergencyEscape


	
(Egress) and Rescue (Ingress) Windows


	
F 2090-10                        Specification for Window Fall Prevention Devices          


	
with Emergency Escape (Egress) Release


	
Mechanisms


	
F 2200-05                        Standard Specification for Automated Vehicular              


	
Gate Construction


	
G 152-06                          Practice for Operating Open Flame Carbon Arc              


	
Light Apparatus for Exposure of Nonmetallic


	
Materials


	
G 154-06                          Practice for Operating Fluorescent Light Apparatus          


	
for UV Exposure of Nonmetallic Materials


	
G 155-05a                        Practice for Operating Xenon Arc Light Apparatus          


	
for Exposure of Nonmetallic Materials

The Association of the Wall and Ceiling Industries International

513 West Broad Street, Suite 210

Falls Church, VA 22046

 

	
AWCI Standard reference number  Title


	
12-B-05                          Technical Manual 12-B Standard Practice for the Testing and Inspection of Field Applied Thin Film Intumescent Fire-resistive Materials; an Annotated Guide, Second Edition

American Wood Protection Association

P.O. Box 361784

Birmingham, AL 35236-1784

 

	
AWPA Standard reference number  Title


	
C1-03                            All Timber Products-Preservative Treatment by Pressure        


	
Processes


	
M4-06                            Standard for the Care of Preservative-treated Wood Products


	
U1-10                            USE CATEGORY SYSTEM: User Specification for Treated          


	
Wood Except Section 6, Commodity Specification H

American Welding Society

550 N.W. LeJeune Road

Miami, FL 33126

 

	
AWS Standard reference number  Title


	
D1.1-10                          Structural Welding Code-Steel


	
D1.3-08                          Structural Welding Code-Sheet Steel


	
D1.4-05                          Structural Welding Code-Reinforcing Steel

Builders Hardware Manufacturers’ Association

355 Lexington Avenue, 17th Floor

New York, NY 10017-6603

 

	
BHMA Standard reference number  Title


	
A 156.10-05                      Power Operated Pedestrian Doors


	
A 156.19-07                      Standard for Power Assist and Low Energy Operated Doors

Canadian General Standards Board

Place du Portage 111, 6B1

11 Laurier Street

Gatineau, Quebec, Canada KIA 1G6

 

	
CGSB Standard Reference Number  Title


	
37-GP-52M (1984)                  Roofing and Waterproofing Membrane, Sheet      


	
Applied, Elastomeric


	
37-GP-56M (1985)                  Membrane, Modified, Bituminous, Prefabricated  


	
and Reinforced for Roofing-with December 1985


	
Amendment


	
CAN/CGSB 37.54-95                Polyvinyl Chloride Roofing and Waterproofing    


	
Membrane

Composite Panel Association

19465 Deerfield Avenue, Suite 306

Leesburg, VA 20176

 

	
CPA Standard reference number  Title


	
ANSI A135.4-2004                Basic Hardboard


	
ANSI A135.5-2004                Prefinished Hardboard Paneling


	
ANSI A135.6-2006                Hardboard Siding

Consumer Product Safety Commission

4330 East West Highway

Bethesda, MD 20814-4408

 

	
CPSC Standard reference number  Title


	
16 CFR Part 1201(1977)          Safety Standard for Architectural Glazing  


	
Material


	
16 CFR Part 1209 (1979)          Interim Safety Standard for Cellulose      


	
Insulation


	
16 CFR Part 1404 (1979)          Cellulose Insulation


	
16 CFR Part 1500 (1991)          Hazardous Substances and Articles;          


	
Administration and Enforcement


	
Regulations


	
16 CFR Part 1500.44 (2001)      Method for Determining Extremely            


	
Flammable and Flammable Solids


	
16 CFR Part 1507 (2001)          Fireworks Devices


	
16 CFR Part 1630 (2000)          Standard for the Surface Flammability of    


	
Carpets and Rugs

Canadian Standards Association

5060 Spectrum Way, Suite 100

Mississauga, Ontario, L4W 5N6 Canada

 

	
CSA Standard reference number  Title


	
101/I.S.2/A440-08              Specifications for Windows, Doors and Unit  


	
Skylights

Cedar Shake and Shingle Bureau

P.O. Box 1178

Sumas, WA 98295-1178

 

	
CSSB Standard reference number  Title


	
CSSB-97                          Grading and Packing Rules for Western Red Cedar Shakes    


	
and Western Red Shingles of the Cedar Shake and Shingle


	
Bureau

Door and Access Systems Manufacturers Association International

1300 Summer Avenue

Cleveland, OH 44115-2851

 

	
DASMA Standard reference number  Title


	
ANSI/DASMA 107-1997


	
(R2004)                          Room Fire Test Standard for Garage Doors Using    


	
Foam Plastic Insulation


	
108-05                            Standard Method for Testing Sectional Garage      


	
Doors and Rolling Doors: Determination of


	
Structural Performance Under Uniform Static Air


	
Pressure Difference


	
115-05                            Standard Method for Testing Sectional Garage      


	
Doors and Rolling Doors: Determination of


	
Structural Performance Under Missile Impact and


	
Cyclic Wind Pressure

U.S. Department of Commerce

National Institute of Standards and Technology

1401 Constitution Avenue, NW

Washington, DC 20230

 

	
DOC Standard reference number  Title


	
PS-1-07                          Structural Plywood


	
PS-2-04                          Performance Standard for Wood-based Structural-use  


	
Panels


	
PS 20-05                        American Softwood Lumber Standard

U.S. Department of Labor

c/o Superintendent of Documents

U.S. Government Printing Office

Washington, DC 20402-9325

 

	
DOL Standard reference number  Title


	
29 CFR Part 1910.1000 (1974)    Air Contaminants

U.S. Department of Transportation

c/o Superintendent of Documents

1200 New Jersey Avenue, SE

Washington, DC 20402-9325

 

	
DOTn Standard reference number  Title


	
49 CFR Parts 100-185-2005        Hazardous Materials Regulations


	
49 CFR Parts 173.137


	
(2005)                          Shippers-General Requirements for Shipments        


	
and Packaging-Class 8-Assignment of Packing


	
Group


	
49 CFR-1998                      Specification of Transportation of Explosive and  


	
Other Dangerous Articles,


	
UN 0335, UN 0336 Shipping Containers

European Committee for Standardization (EN)

Central Secretariat

Rue de Stassart 36

B-10 50 Brussels

 

	
EN Standard reference number  Title


	
EN 1081-98                      Resilient Floor Coverings-Determination of the Electrical


	
Resistance

Federal Emergency Management Agency

Federal Center Plaza

500 C Street S.W.

Washington, DC 20472

 

	
FEMA Standard reference number  Title


	
FIA-TB11-01                      Crawlspace Construction for Buildings Located in  


	
Special Flood Hazard Areas

Factory Mutual Global Research

Standards Laboratories Department

1301 Atwood Avenue, P.O. Box 7500

Johnson, RI 02919

 

	
FM Standard reference number  Title


	
4450 (1989)                    Approval Standard for Class 1 Insulated Steel Deck          


	
Roofs-with Supplements through July 1992


	
4470 (2010)                    Approval Standard for Class 1 Roof Covers


	
4474 (04)                      Evaluating the Simulated Wind Uplift Resistance of Roof      


	
Assemblies Using Static Positive and/or Negative


	
Differential Pressures


	
4880 (2010)                    American National Standard for Evaluating Insulated Wall      


	
or Wall and Roof/ Ceiling Assemblies, Plastic Interior


	
Finish Materials, Plastic Exterior Building Panels,


	
Wall/Ceiling Coating Systems, Interior and Exterior Finish


	
Systems

Gypsum Association

810 First Street N.E. 510

Washington, DC 20002-4268

 

	
GA Standard reference number  Title


	
GA 216-10                      Application and Finishing of Gypsum Panel Products


	
GA 600-09                      Fire-resistance Design Manual, 18th Edition

Hardwood Plywood Veneer Association

1825 Michael Faraday Drive

Reston, VA 20190-5350

 

	
HPVA Standard reference number  Title


	
HP-1-2009                        Standard for Hardwood and Decorative Plywood

U.S. Department of Housing and Urban Development

451 7th Street, SW,

Washington, DC 20410

 

	
HUD Standard reference number  Title


	
HUD 24 CFR Part 3280 (1994)      Manufactured Home Construction and


	
Safety Standards

International Code Council, Inc.

500 New Jersey Ave, NW 6th Floor

Washington, DC 20001

 

	
ICC Standard reference number  Title


	
ICC/ANSI A117.1- 09              Accessible and Usable Buildings and Facilities


	
ICC 300-07                      ICC Standard on Bleachers, Folding and Telescopic      


	
Seating and


	
ICC 400-07                      Standard on Design and Construction of Log            


	
Structures


	
ICC 500-08                      ICC/NSSA Standard on the Design and                  


	
Construction of Storm


	
ICC 600-08                      Standard for Residential Construction in High Wind    


	
Regions


	
lEBC – 09                      International Existing Buildings Code


	
lECC-09                          International Energy Conservation Code (adoption      


	
includes only section 101 of chapter 1 and chapters


	
2 through 6)


	
IPC-09                          International Fire Code


	
IFGC-09                          International Fuel Gas Code (including ICC            


	
Emergency Amendment changing IFGC Sections


	
406.7)


	
SBCCI SSTD 11-99                Test Standard for Determining Wind Resistance of      


	
Concrete or Clay Roof Tiles

International Organization for Standardization

ISO Central Secretariat,

1 ch, de la Voie-Creuse,

Case Postale 56

CH-1211 Geneva 20, Switzerland

 

	
ISO Standard reference number  Title


	
ISO 8115-86                      Cotton Bales-Dimensions and Density

National Association of Architectural Metal Manufacturers,

800 Roosevelt Road,

Bldg. C, Suite 312

Glen Ellyn, IL 60137

 

	
NAAMM Standard reference number  Title


	
FP 1001-07                        Guide Specifications for Design of Metal Flag Poles

National Concrete Masonry Association,

13750 Sunrise Valley,

Herndon, VA 22071-4662

 

	
NCMA Standard reference number  Title


	
TEK5-08                          Details for Concrete Masonry Fire Walls

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02269-9101

 

	
NFPA Standard reference number  Title


	
10-10                            Portable Fire Extinguishers


	
11-10                            Low Expansion Foam


	
12-08                            Carbon Dioxide Extinguishing Systems


	
12A-04                          Halon 1301 Fire Extinguishing Systems


	
13-10                            Installation of Sprinkler Systems (including TIA 10-2)


	
13D-10                          Installation of Sprinkler Systems in One- and Two-      


	
family Dwellings and Manufactured Homes


	
(including TIA 10-2)


	
13R-10                          Installation of Sprinkler Systems in Residential          


	
Occupancies Up to and Including Four Stories in


	
Height (including TIA 10-2)


	
14-10                            Installation of Standpipe and Hose System


	
16-07                            Installation of Foam-water Sprinkler and Foam-          


	
water Spray Systems


	
17-09                            Dry Chemical Extinguishing Systems


	
17A-09                          Wet Chemical Extinguishing


	
20-10                            Installation of Stationary Pumps for Fire Protection


	
30-08                            Flammable and Combustible Liquids Code


	
31-06                            Installation of Oil-burning Equipment


	
32-07                            Dry Cleaning Plants


	
40-11                            Storage and Handling of Cellulose Nitrate Film


	
58-11                            Liquefied Petroleum Gas Code


	
61-08                            Prevention of Fires and Dust Explosions in              


	
Agricultural and Food Product Facilities


	
70-08                            National Electrical Code (This edition applies only      


	
to one-, two-, and three family dwellings)


	
70-11                            National Electrical Code (including TIA 11-1) (This      


	
edition applies to all buildings other than one-, two-


	
, and three-family dwellings)


	
72-10                            National Fire Alarm Code


	
80-10                            Fire Doors and Other Opening Protectives


	
85-07                            Boiler and Combustion System Hazards Code                


	
(Note: NFPA 8503 has been incorporated into


	
NFPA 85)


	
92B-09                          Smoke Management Systems in Malls, Atria and              


	
Large Spaces


	
99-05                            Standard for Health Care Facilities


	
105-10                          Standard for the Installation of Smoke Door              


	
Assemblies


	
110-10                          Emergency and Standby Power Systems


	
111-10                          Stored Electrical Energy Emergency and Standby          


	
Power Systems


	
120-10                          Coal Preparation Plants


	
170-09                          Standard for Fire Safety and Emergency Symbols


	
211-10                          Chimneys, Fireplaces, Vents and Solid Fuel-              


	
burning


	
252-08                          Standard Methods of Fire Tests of Door Assemblies


	
253-06                          Test for Critical Radiant Flux of Floor Covering          


	
Systems Using a Radiant Heat Energy Source


	
257-07                          Standard for Fire Test for Window and Glass Block        


	
Assemblies


	
259-08                          Test Method for Potential Heat of Building              


	
Materials


	
265-07                          Method of Fire Tests for Evaluating Room Fire            


	
Growth Contribution of Textile Wall Coverings on


	
Full Height Panels and Walls


	
268-07                          Standard Test Method for Determining Ignitibility        


	
of Exterior Wall Assemblies Using a Radiant Heat


	
Energy Source


	
285-06                          Standard Method of Test for the Evaluation of            


	
Flammability Characteristics of Exterior Nonload-


	
bearing Wall Assemblies Containing Combustible


	
Components


	
286-06                          Standard Method of Fire Test for Evaluating              


	
Contribution of Wall and Ceiling Interior Finish to


	
Room Fire Growth


	
288-07                          Standard Method of Fire Tests of Floor Fire Door          


	
Assemblies Installed Horizontally in Fire-


	
resistance-rated Floor Systems


	
409-11                          Aircraft Hangars


	
418-06                          Standard for Heliports


	
484-09                          Combustible Metals


	
654-06                          Prevention of Fire & Dust Explosions from the        


	
Manufacturing, Processing and Handling of


	
Combustible Particulate Solids


	
655-07                          Prevention of Sulfur Fires and Explosions


	
664-07                          Prevention of Fires and Explosions in Wood              


	
Processing and Woodworking Facilities


	
701-10                          Standard Methods of Fire Tests for Flame-                


	
propagation of Textiles and Films


	
704-07                          Standard System for the Identification of the            


	
Hazards of Materials for Emergency Response


	
1124-06                          Manufacture, Transportation and Storage of              


	
Fireworks and Pyrotechnic Articles


	
2001-08                          Clean Agent Fire Extinguishing Systems

Precast Prestressed Concrete Institute

175 W. Jackson Boulevard, Suite 500

Chicago, IL 60604-6938

 

	
PCI Standard reference number  Title


	
MNL 124-89                      Design for Fire Resistance of Precast Prestressed  


	
Concrete


	
MNL 128-01                      Recommended Practice for Glass Fiber Reinforced      


	
Concrete Panels

Post-Tensioning Institute

8601 North Black Canyon Highway, Suite 103

Phoenix, AZ 85021

 

	
PTI Standard reference number  Title


	
PTI-2008                        Standard Requirements for Analysis of Shallow Concrete      


	
Foundations on Expansive Soils, Third Edition


	
PTI-2008                        Standard Requirements for Design of Shallow Post-          


	
tensioned Concrete Foundation on Expansive Soils, Second


	
Edition

Rack Manufacturers Institute

8720 Red Oak Boulevard, Suite 201

Charlotte, NC 28217

 

	
RMI Standard reference number  Title


	
ANSI/MH16.1-08                  Specification for Design, Testing and Utilization of  


	
Industrial Steel Storage Racks

Steel Deck Institute,

P. O. Box 25

Fox River Grove, IL 60021

 

	
SDI Standard reference number  Title


	
ANSI/NC1.0-06                  Standard for Noncomposite Steel Floor Deck


	
ANSI/RD1.0-06                  Standard for Steel Roof Deck

Steel Joist Institute,

1173B London Links Drive

Forest, VA 24551

 

	
SJI Standard reference number  Title


	
CJ-1.0-06                      Standard Specification for Composite Steel Joists,  


	
CJ-series


	
JG-1.1-05                      Standard Specification for Joist Girders


	
K-1.1-05                        Standard Specification for Open Web Steel Joists,    


	
K- series


	
LH/DLH-1.1-05                  Standard Specification for Longspan Steel Joists,    


	
LH-series and Deep Longspan Steel Joists, DLH-


	
series

Single-Ply Roofing Institute,

411 Waverly Oaks Road, Suite 331B,

Waltham, MA 02452

 

	
SPRI Standard reference number  Title


	
SPRI/ANSI/ES-1-03                Wind Design Standard for Edge Systems Used with  


	
Low Slope Roofing Systems


	
RP-4-02                          Wind Design Guide for Ballasted Single-ply        


	
Roofing Systems

Telecommunications Industry Association

2500 Wilson Boulevard

Arlington, VA 22201-3834

 

	
TIA Standard reference number  Title


	
TIA-222-G-09                    Structural Standards for Steel Antenna Towers and      


	
Antenna Supporting Structures including-Addendum 1,


	
222-G-1, Dated 2007

The Masonry Society,

3970 Broadway, Unit 201-D,

Boulder, CO 80304-1135

 

	
TMS Standard reference number  Title


	
0216-07                          Standard Method for Determining Fire Resistance of      


	
Concrete and Masonry Construction Assemblies


	
0302-07                          Standard Method for Determining the Sound Transmission  


	
Class Rating for Masonry Walls


	
402-08                          Building Code Requirements for Masonry Structures


	
602-08                          Specification for Masonry Structures

Truss Plate Institute,

218 N. Lee Street, Suite 312

Alexandria, VA 22314

 

	
TPI Standard reference number  Title


	
TPI 1-2007                      National Design Standards for Metal-plate-connected  


	
Wood Truss Construction

Underwriters Laboratories, Inc.

333 Pfingsten Road

Northbrook, IL 60062-2096

 

	
UL Standard reference number  Title


	
9-09                          Fire Tests of Window Assemblies


	
10A-09                          Tin Clad Fire Doors


	
10B-08                          Fire Tests of Door Assemblies


	
10C-09                          Positive Pressure Fire Tests of Door Assemblies


	
14B-08                          Sliding Hardware for Standard Horizontally-mounted Tin        


	
Clad Fire Doors


	
14C-06                          Swinging Hardware for Standard Tin Clad Fire Doors            


	
Mounted Singly and in Pairs


	
103-10                          Factory-built Chimneys, for Residential Type and Building      


	
Heating Appliances


	
127-08                          Factory-built Fireplaces


	
199E-04                        Outline of Investigation for Fire Testing of Sprinklers and  


	
Water Spray Nozzles for Protection of Deep Fat Fryers.


	
217-06                          Single and Multiple Station Smoke Alarms


	
263-03                          Standard for Fire Test of Building Construction and          


	
Materials


	
268-09                          Smoke Detectors for Fire Protective Signaling Systems


	
300-05                          Fire Testing of Fire Extinguishing Systems for Protection      


	
of Restaurant Cooking Areas


	
305-97                          Panic Hardware


	
325-02                          Door, Drapery, Gate, Louver and Window Operations and          


	
Systems-with Revisions through February 2006


	
555-2006                      Fire Dampers


	
555C-2006                      Ceiling Dampers


	
555S-99                        Smoke Dampers-with Revisions through July 2006


	
580-2006                      Test for Uplift Resistance of Roof Assemblies


	
641-95                          Type L Low-temperature Venting Systems


	
710B-04                        Recirculating Systems-with Revisions through April 2006


	
723-08                          Standard for Test for Surface Burning Characteristics of      


	
Building Materials


	
790-04                          Standard Test Methods for Fire Tests of Roof Coverings


	
793-08                          Standards for Automatically Operated Roof Vents for          


	
Smoke and Heat


	
864-03                          Standards for Control Units and Accessories for Fire Alarm    


	
Systems-with Revisions through March 2006


	
924-06                          Standard for Safety Emergency Lighting and Power              


	
Equipment


	
1040-96                        Fire Test of Insulated Wall Construction-with Revisions      


	
through June 2001


	
1256-02                        Fire Test of Roof Deck Construction-with Revisions            


	
through January 2007


	
1479-03                        Fire Tests of Through-penetration Firestops-with              


	
Revisions through April 2007


	
1482-10                        Solid-fuel-type Room Heater


	
1715-97                        Fire Test of Interior Finish Material-with Revisions          


	
through March 2004


	
1777-07                        Chimney Liners


	
1784-01                        Air Leakage Tests of Door Assemblies-with Revisions          


	
through December 2004


	
1897-04                        Uplift Tests for Roof Covering Systems


	
1975-06                        Fire Test of Foamed Plastics Used for Decorative Purposes


	
1994-04                        Standard for Luminous Egress Path Marking Systems-            


	
with Revisions through February 2005


	
2017-08                        Standards for General-purpose Signaling Devices and          


	
Systems


	
2079-04                        Tests for Fire Resistance of Building Joint Systems-with      


	
Revisions through March 2006


	
2200-98                        Stationary Engine Generator Assemblies

Underwriters Laboratories of Canada,

7 Underwriters Road,

Toronto, Ontario, Canada M1R3B4

 

	
ULC Standard reference number  Title


	
CAN/ULC S102.2-2010              Standard Method of Test for Surface Burning        


	
Characteristics of Flooring, Floor Coverings and


	
Miscellaneous Materials and Assemblies-with


	
2000 Revisions

United States Code,

c/o Superintendent of Documents

U.S. Government Printing Office,

Washington, DC 20402-9325

 

	
USC Standard reference number                                      Title


	
10 U.S.C. Sections 18233(A)(1) and 10 U.S.C. Sections 18237-1994


	
18 USC Part 1, Ch.40                                              Importation, Manufacture, Distribution and Storage  


	
of Explosive Materials

Window and Door Manufacturers Association

1400 East Touhy Avenue 470

Des Plaines, IL 60018

 

	
WDMA Standard reference number  Title


	
AAMA/WDMA/CSA


	
101/I.S.2/A440-08                Specifications for Windows, Doors and Unit  


	
Skylights

Wire Reinforcement Institute, Inc. 942 Main Street, Suite 300 Hartford, CT 06103

 

	
WRI Standard reference number  Title


	
WRI/CRSI-81                      Design of Slab-on-ground Foundations-with 1996 Update

Effective: 03/15/2012 R.C. 119.032 review dates: 11/01/2016 Promulgated Under: 119.03 Statutory Authority: 3781.10(A) Rule Amplifies: 3781.10, 3781.11, 3791.04 Prior Effective Dates: 9/1/92, 2/1/93, 7/1/95, 7/1/97, 3/1/98, 7/1/98, 1/1/99, 12/1/00, 1/1/02, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08, 1/1/09, 11/1/11

Rescinded eff 7-1-07

Rescinded eff 7-1-07

Rescinded eff 7-1-07

Rescinded eff 7-1-07