LAW
Writer®
Ohio Laws and Rules
3501.1 General. This chapter lists the standards that are referenced in various sections of the building code. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title. The application of the referenced standards shall be as specified in Section 102.4.
3501.2 Referenced codes. When indicated in this code, the following codes refer to provisions in the listed chapters of the administrative code:
Building Code 4101:1-1 to 4101:1-35
Energy Code 4101:1-13
Fire Code 1301:7-1 to 1301:7-7
Mechanical Code 4101:2-1 to 4101:2-15
Ohio Boiler and Pressure Vessel Rules 4101:4-1 to 4101:4-10
Ohio Elevator Code 4101:5-1 to 4101:5-3
Residential Code of Ohio for One, Two and
Three Family Dwellings (2006 edition) 4101:8-1 to 4101:8-43
Plumbing Code 4101:3-1 to 4101:3-13
3501.3 Americans with Disabilities Act accessibility guidelines. When reference is made to ADAAG in this code, it shall mean the “ADA Standards for Accessible Design” also known as “ADA Accessibility Guidelines for Buildings and Facilities”, “28 CFR Part 36 Appendix A” Code of Federal Regulations as reprinted and the version available on the U.S. department of justice’s website at http://www.usdoj.gov/crt/ada/stdspdf.htm.
3501.4 Building Code Referenced Standards.
Aluminum Association
900 – 19th Street N.W., Suite 300
Washington, DC 20006
AA
Standard reference number Title
ADM 1-05 Aluminum Design Manual: Part 1-A Aluminum Structures, Allowable Stress Design; and Part 1-B-Aluminum Structures, Load and Resistance Factor Design of Buildings and Similar Type Structures
ASM 35-00 Aluminum Sheet Metal Work in Building Construction (Fourth Edition)
American Architectural Manufacturers Association
1827 Waldon Office
Square, Suite 550
Schaumburg, IL 60173
AAMA
Standard reference number Title
1402-86 Standard Specifications for Aluminum Siding, Soffit and Fascia
101/I.S.2/A440-05 Specifications for Windows, Doors and Unit Skylights*
*Note: Also see CSA and WDMA
American Concrete Institute
P.O. Box 9094
Farmington Hills, MI 48333-9094
ACI
Standard reference number Title
216.1-97 Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies
318-05 Building Code Requirements for Structural Concrete
530-05 Building Code Requirements for Masonry Structures
530.1-05 Specifications for Masonry Structures
American Forest & Paper Association 1111 19th St, NW Suite 800
Washington, DC 20036
AF&PA
Standard reference number Title
WCD No. 4-89 Wood Construction Data-Plank and Beam Framing for Residential Buildings
WFCM-01 Wood Frame Construction Manual for One- and Two-Family Dwellings
T.R. No. 7-87 Technical Report-Basic Requirements for Permanent Wood Foundation System
NDS-05 National Design Specification (NDS) for Wood Construction with 2005 Supplement
AF&PA-93 Span Tables for Joists and Rafters
SDPWS-05 AF&PA Supplement Special Design Provisions for Wind and Seismic
American Hardboard Association
1210 West N.W. Highway
Palatine, IL 60067
AHA
Standard Reference number Title
A135.4-2004 Basic Hardboard
A135.5-2004 Prefinished Hardboard Paneling
A135.6-1998 Hardboard Siding
American Institute of Steel Construction
One East Wacker Drive, Suite 3100
Chicago, IL 60601-2001
AISC
Standard reference number Title
341-05 Seismic Provisions for Structural Steel Buildings, including Supplement No. 1 dated 2006
360-05 Specification for Structural Steel Buildings
American Iron and Steel Institute
1140 Connecticut Avenue
Suite 705
Washington, DC 20036
AISI
Standard reference number Title
NAS-01 North American Specification for the Design of Coldformed Steel Structural Members, including 2004 Supplement
General-04 Standard for Cold-formed Steel Framing-General Provisions
Header-04 Standard for Cold-formed Steel Framing-Header Design
Lateral-04 Standard for Cold-formed Steel Framing-Lateral Design
PM-01 Standard for Cold-formed Steel Framing-Prescriptive Method for One- and Two-family Dwellings, including 2004 Supplement
Truss-04 Standard for Cold-formed Steel Framing-Truss Design
WSD-04 Standard for Cold-formed Steel Framing-Wall Stud Design
American Institute of Timber Construction
Suite 140
7012 S. Revere Parkway
Englewood, CO 80112
AITC
Standard reference number Title
AITC Technical Note 7-96 Calculation of Fire Resistance of Glued Laminated Timbers
AITC 104-03 Typical Construction Details
AITC 110-01 Standard Appearance Grades for Structural Glued Laminated Timber
AITC 113-01 Standard for Dimensions of Structural Glued Laminated Timber
AITC 117-04 Standard Specifications for Structural Glued Laminated Timber of Softwood Species
AITC 119-96 Standard Specifications for Structural Glued Laminated Timber of Hardwood Species
AITC 200-04 Manufacturing Quality Control Systems Manual for
Structural Glued Laminated Timber
ANSI/AITC A 190.1-02 Structural Glued Laminated Timber
Automotive Lift Institute
P.O. Box 85
Courtland, NY 13045
ALI
Standard reference number Title
ALI ALCTV-98 Standard for Automotive Lifts -Safety Requirements for Construction, Testing and Validation (ANSI)
American National Standards Institute
25 West 43rd Street, Fourth Floor
New York, NY 10036
ANSI
Standard reference number Title
A13.1-96 Scheme for the Identification of Piping Systems (Reaffirmed 2002)
A108.1A-05 Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar
A108.1B-05 Installation of Ceramic Tile, quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set or Latexportland Mortar
A108.4-05 Installation of Ceramic Tile with Organic Adhesives or Water-cleanable Tile-setting Epoxy Adhesive
A108.5-05 Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex-portland Cement Mortar
A108.6-05 Installation of Ceramic Tile with Chemical-resistant, Water Cleanable Tile-setting and -grouting Epoxy
A108.8-05 Installation of Ceramic Tile with Chemical-resistant Furan Resin Mortar and Grout
A108.9-05 Installation of Ceramic Tile with Modified Epoxy Emulsion Mortar/Grout
A108.10-05 Installation of Grout in Tilework
A118.1-05 American National Standard Specifications for Dry-set Portland Cement Mortar
A118.3-05 American National Standard Specifications for Chemicalresistant, Water-cleanable Tile-setting and -grouting Epoxy and Water Cleanable Tile-setting Epoxy Adhesive
A118.4-05 American National Standard Specifications for Latexportland Cement Mortar
A118.5-05 American National Standard Specifications for Chemical Resistant Furan Mortar and Grouts for Tile Installation
A118.6-05 American National Standard Specifications for Cement Grouts for Tile Installation
A118.8-05 American National Standard Specifications for Modified Epoxy Emulsion Mortar/Grout
A136.1-05 American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile
A137.1-88 American National Standard Specifications for Ceramic Tile
A208.1-99 Particleboard
Z 97.1-04 Safety Glazing Materials Used in Buildings-Safety Performance Specifications and Methods of Test (Reaffirmed 1994)
APA – Engineered Wood Association
P.O. Box 11700
Tacoma, WA 98411-0700
APA
Standard reference number Title
APA PDS-04 Panel Design Specification
APA PDS
Supplement 1-90 Design and Fabrication of Plywood Curved Panels (revised 1995)
APA PDS
Supplement 2-92 Design and Fabrication of Plywood-lumber beams (revised 1998)
APA PDS
Supplement 3-90 Design and Fabrication of Plywood Stressed-skin Panels (revised 1996)
APA PDS
Supplement 4-90 Design and Fabrication of Plywood Sandwich Panels (revised 1993)
APA PDS
Supplement 5-95 Design and Fabrication of All-plywood Beams (revised 1995)
EWS R540-02 Builders Tips: Proper Storage and Handling of Glulam Beams
EWS S475-02 Glued Laminated Beam Design Tables
EWS S560-03 Field Notching and Drilling of Glued Laminated Timber Beams
EWS T300-05 Glulam Connection Details
EWS X440-03 Product Guide-Glulam
EWS X450-01 Glulam in Residential Construction -Western Edition
American Society of Agricultural Engineers
2950 Niles Road
St. Joseph, MI 49085-9659
ASAE
Standard reference number Title
EP 484.2(1998) Diaphragm Design of Metal-clad Post-frame Rectangular Buildings
EP 486.1(2000) Shallow-post Foundation Design
EP 559(2003) Design Requirements and Bending Properties for Mechanically Laminated Columns
American Society of Civil Engineers
Structural Engineering Institute
1801 Alexander Bell Drive
Reston, VA 20191-4400
ASCE/SEI
Standard reference number Title
3-91 Structural Design of Composite Slabs
5-05 Building Code Requirements for Masonry Structures
6-05 Specifications for Masonry Structures
7-05 Minimum Design Loads for Buildings and Other Structures including Supplement No. 1 and excluding Chapter 14 and Appendix 11A
8-02 Standard Specification for the Design of Cold-formed Stainless Steel Structural Members
19-96 Structural Applications of Steel Cables for Buildings
24-05 Flood Resistant Design and Construction
29-05 Standard Calculation Methods for Structural Fire Protection
32-01 Design and Construction of Frost Protected Shallow Foundations
American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.
1791 Tullie Circle, NE
Atlanta, GA 30329-2305
ASHRAE
Standard Reference Number Title
ASHRAE 90.1-2004 Energy Standard for Buildings Except Low-Rise Buildings
American Society of Mechanical Engineers
Three Park Avenue
New York, NY 10016-5990
ASME
Standard reference number Title
A17.1-04 Safety Code for Elevators and Escalators with
A17.1a-2004 addenda and A17.1S Supplement
A90.1-03 Safety Standard for Belt Manlifts
B16.18-2001(R2005) Cast Copper Alloy Solder Joint Pressure Fittings
B16.22-2001(R2005) Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
B31.3-2004 Process Piping
ASTM International
100 Barr Harbor Drive
West Conshohocken, PA 19428-2959
ASTM
Standard reference number Title
A 6/A 6M-05a Specification for General Requirements for Rolled Steel, Structural Steel Bars, Plates, Shapes, and Sheet Piling
A 36/A 36M-05 Specification for Carbon Structural Steel
A 82-05 Specification for Steel Wire, Plain, for Concrete Reinforcement
A 123/A 123M-02 Specification for Zinc (Hot-dip Galvanized) Coating on Iron and Steel Products
A 153-05 Specification for Zinc Coating (Hot-dip) on Iron and Steel Hardware
A 185-06e1 Specification for Steel Welded Wire Reinforcement, Plain for Concrete
A 240-05a Standard Specification for Chromium and Chromiumnickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications
A 252-98 (2002) Specification for Welded and Seamless Steel Pipe Piles
A 283/A 283M-03 Specification for Low and Intermediate Tensile Strength Carbon Steel Plates
A 307-04 Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength
A 416/A 416M-05 Specification for Steel Strand, Uncoated Seven-wire for Prestressed Concrete
A 421/A 421M-05 Specification for Uncoated Stress-relieved Steel Wire for Prestressed Concrete
A 435/A 435M-90(2001) Specification for Straight-beam Ultrasonic Examination of Steel Plates
A 463/A 463M-05 Specification for Steel Sheet, Aluminum-coated, by the Hot Dip Process
A 480/A480M-06 Specification for General Requirements for Flat-rolled Stainless and Heat-resisting Steel Plate, Sheet, and Strip
A 496-05 Specification for Steel Wire, Deformed for Concrete Reinforcement
A 497-06e1 Specification for Steel Welded Reinforcement Deformed, for Concrete
A 510-03 Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel
A 568/A 568M-05 Specification for Steel, Sheet, Carbon, and High-strength, Low-alloy, Hot-rolled and Cold-rolled, General Requirements for
A 572/A 572M-06 Specification for High-strength Low-alloy Columbiumvanadium Structural Steel
A 588/A 588M-05 Specification for High-strength Low-alloy Structural Steel with 50 ksi (345 Mpa) Minimum Yield Point to 4 inches (100 mm) Thick
A 615/A 615M-06a Specification for Deformed and Plain Billet-steel Bars for Concrete Reinforcement
A 641/A 641M-03 Specification for Zinc-coated (Galvanized) Carbon Steel Wire
A 653/A 653M-05a Specification for Steel Sheet, Zinc-coated Galvanized or Zinc-iron Alloy-coated Galvannealed by the Hot-dip Process
A 690-00a Standard Specification for High Strength Low-alloy Steel H-piles and Sheet Piling for Use in Marine Environments
A 706/A 706M-06a Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement
A 722/A 722M- 05 Specification for Uncoated High-strength Steel Bar for Prestressing Concrete
A 755/A 755M-03 Specification for Steel Sheet, Metallic-coated by the Hotdip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products
A 767/A 767M-05 Specification for Zinc-coated (Galvanized) Steel Bars for Concrete Reinforcement
A 775/A 775M-04a Specification for Epoxy-coated Steel Reinforcing Bars
A 792/A 792M-05 Specification for Steel Sheet, 55% Aluminum-zinc Alloycoated by the Hot-dip Process
A 875/A 875M-05 Standard Specification for Steel Sheet Zinc-5 percent, Aluminum Alloy-coated by the Hot-dip Process
A 884-02 Specification for Epoxy-coated Steel Wire and Welded Wire Fabric for Reinforcement
A 898/A 898M-91(2001) Specification for Straight Beam Ultrasonic Examination of Rolled Steel Shapes
A 899-91 (2002) Specification for Steel Wire Epoxy-coated
A 913/A 913M-04 Specification for High-strength Low-alloy Steel Shapes of Structural Quality, Produced by Quenching and Selftempering Process (QST)
A924-04 Standard Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-dip Process
A 951-02 Specification for Masonry Joint Reinforcement
A 992-06 Standard Specification for Structural Shapes
A 996/A 996M-06a Specification for Rail-steel and Axle-steel Deformed Bars for Concrete Reinforcement
A1008/A1008M-05a Specification for Steel, Sheet, Cold-rolled, Carbon, Structural, High-strength Low alloy and High-strength Low-alloy with Improved Formability
B 42-02e01 Specification for Seamless Copper Pipe, Standard Sizes
B 43-98(2004) Specification for Seamless Red Brass Pipe, Standard Sizes
B 68-02 Specification for Seamless Copper Tube, Bright Annealed (Metric)
B 88-03 Specification for Seamless Copper Water Tube
B 101-02 Specification for Lead-coated Copper Sheet and Strip for Building Construction
B 209-04 Specification for Aluminum and Aluminum Alloy Steel and Plate
B 251-02e01 Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube
B 280-03 Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
B 370-03 Specification for Cold-rolled Copper Sheet and Strip for Building Construction
B 695-04 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
C 5-03 Specification for Quicklime for Structural Purposes
C 22/C 22M-00 Specification for Gypsum
C 27-98 (2002) Specification for Standard Classification of Fireclay and High-alumina Refractory Brick
C 28/C 28M-05 Specification for Gypsum Plasters
C 31/31M-03a Practice for Making and Curing Concrete Test Specimens in the Field
C 33-03 Specification for Concrete Aggregates
C 34-03 Specification for Structural Clay Load-bearing Wall Tile
C 35-05 Specification for Inorganic Aggregates for Use in Gypsum Plaster
C 36/C 36M-03 Specification for Gypsum Wallboard
C 37/C 37M-01 Specification for Gypsum Lath
C 55-03 Specification for Concrete Brick
C 56- 05 Specification for Structural Clay Non-load Bearing Tile
C 59/C 59M-00(2006)Specification for Gypsum Casting and Molding Plaster
C 61/C 61M-00(2006)Specification for Gypsum Keene’s Cement
C 62-05 Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)
C 67-06 Test Methods of Sampling and Testing Brick and Structural Clay Tile
C 73-05 Specification for Calcium Silicate Face Brick (Sand-lime Brick)
C 79-04a Specification for Treated Core and Nontreated Core Gypsum Sheathing Board
C 90-05a Specification for Loadbearing Concrete Masonry Units
C 91-05 Specification for Masonry Cement
C 94/C 94M-05 Specification for Ready-mixed Concrete
C109/C109M-05 Specification for Ready-mixed Concrete Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
C 126-99(2005) Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
C 140-05e1 Test Method Sampling and Testing Concrete Masonry Units and Related Units
C 150-05 Specification for Portland Cement
C 172-04 Practice for Sampling Freshly Mixed Concrete
C 199-84(2005) Test Method for Pier Test for Refractory Mortars
C 206-03 Specification for Finishing Hydrated Lime
C 207-0406 Specification for Hydrated Lime for Masonry Purposes
C 208-95 (2001) Specification for Cellulosic Fiber Insulating Board
C 212-00(2006) Specification for Structural Clay Facing Tile
C 216-05a Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
C 270-06 Specification for Mortar for Unit Masonry
C 315-02 Specification for Clay Flue Linings
C 317/C 317M-00(2005) Specification for Gypsum Concrete
C 330-05 Specification for Lightweight Aggregates for Structural Concrete
C 331-05 Specification for Lightweight Aggregates for Concrete Masonry Units
C 406-06 Specification for Roofing Slate
C 442/C 442M-04 Specification for Gypsum Backing Board and Coreboard and Gypsum Shaftliner Board
C 472-99 (2004) Specification for Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete
C 473-05 Test Method for Physical Testing of Gypsum Panel Products
C 474-05 Test Methods for Joint Treatment Materials for Gypsum Board Construction
C 475-02 Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard
C 476-02 Specification for Grout for Masonry
C 503-05 Specification for Marble Dimension Stone (Exterior)
C 514-04 Specification for Nails for the Application of Gypsum Board
C 516-02 Specifications for Vermiculite Loose Fill Thermal Insulation
C 547-06 Specification for Mineral Fiber Pipe Insulation
C 549-06 Specification for Perlite Loose Fill Insulation
C 552-03 Standard Specification for Cellular Glass Thermal Insulation
C 557-03e1 Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing
C 568-03 Specification for Limestone Dimension Stone
C 578-05 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
C 587-04 Specification for Gypsum Veneer Plaster
C 588/C 588M-03 Specification for Gypsum Base for Veneer Plasters
C 595-05 Specification for Blended Hydraulic Cements
C 615-03 Specification for Granite Dimension Stone
C 616-03 Specification for Quartz Dimension Stone
C 629-03 Specification for Slate Dimension Stone
C 630/C 630M-03 Specification for Water-resistant Gypsum Backing Board
C 631-95a(2004) Specification for Bonding Compounds for Interior Gypsum Plastering
C 635-04 Specification for the Manufacturer, Performance and Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings
C 636-04 Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels
C 645-06 Specification for Nonstructural Steel Framing Members
C 652-05 Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)
C 728-05 Standard Specification for Perlite Thermal Insulation Board
C 744-05 Specification for Prefaced Concrete and Calcium Silicate Masonry Units
C 754-04 Specification for Installation of Steel Framing Members to Receive Screw-attached Gypsum Panel Products
C 836-05 Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course
C 840-04a Specification for Application and Finishing of Gypsum Board
C 841-03 Specification for Installation of Interior Lathing and Furring
C 842-05 Specification for Application of Interior Gypsum Plaster
C 843-99e01 Specification for Application of Gypsum Veneer Plaster
C 844-04 Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
C 847-04 Specification for Metal Lath
C 887-05 Specification for Packaged, Dry Combined Materials for Surface Bonding Mortar
C 897-05 Specification for Aggregate for Job-mixed Portland Cement-based Plasters
C 926-98a(2005) Specification for Application of Portland Cement Basedplaster
C 931/C 931M-04 Specification for Exterior Gypsum Soffit Board
C 932-05 Specification for Surface-applied Bonding Agents for Exterior Plastering
C 933-05 Specification for Welded Wire Lath
C 946-91(2001) Specification for Practice for Construction of Dry-stacked, Surface-bonded Walls
C 954-05 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 inch (0.84 mm) to 0.112 inch (2.84 mm) in Thickness
C 955-06 Standard Specification for Load-bearing Transverse and Axial Steel Studs, Runners Tracks, and Bracing or Bridging, for Screw Application of Gypsum Panel Products and Metal Plaster Bases
C 956-04 Specification for Installation of Cast-in-place Reinforced Gypsum Concrete
C 957-05 Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane with Integral Wearing Surface
C 960/C960M-04 Specification for Predecorated Gypsum Board C1002-04 Specification for Steel Self-piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
C1006-84 (2001) Test Method for Splitting Tensile Strength of Masonry Units
C1007-04 Specification for Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories
C1019-05 Test Method of Sampling and Testing Grout
C1029-05a Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation
C1032-06 Specification for Woven Wire Plaster Base
C1047-05 Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
C1063-03 Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement Based Plaster
C 1072-05b Standard Text Method for Measurement of Masonry Flexural Bond Strength
C1088-05 Specification for Thin Veneer Brick Units Made from Clay or Shale
C1167-03 Specification for Clay Roof Tiles
C1177/C1177M-04e1 Specification for Glass Mat Gypsum Substrate for Use as Sheathing
C1178/C1178M-04e1 Specification for Glass Mat Water-resistant Gypsum Backing Panel
C1186-02 Specification for Flat Nonasbestos Fiber Cement Sheets
C1261-05 Specification for Firebox Brick for Residential Fireplaces
C1278/C 1278M-03e1Specification for Fiber-reinforced Gypsum Panels
C1280-04 Specification fo r Application of Gypsum Sheathing
C1283-03e01 Practice for Installing Clay Flue Liners
C1288-99(2004) Standard Specification for Discrete Nonasbestos Fibercement Interior Substrate Sheets
C1289-06 Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board
C1314-03b Test Method for Compressive Strength of Masonry Prisms
C1325-04 Standard Specification for Nonasbestos Fiber-mat Reinforced Cement Interior Substrate Sheets
C1328-05 Specification for Plastic (Stucco Cement)
C1329-05 Specification for Mortar Cement
C1386-98 Specification for Precast Autoclaved Aerated Concrete (PAAC) Wall Construction Units
C1395/1395M-04 Specification for Gypsum Ceiling Board
C1396-06 Standard Specifications for Gypsum Wallboard
C1405-05 Standard Specification for Glazed Brick (Single Fired, Solid Brick Units)
C1492-03 Standard Specification for Concrete Roof Tile
D 25-99(2005) Specification for Round Timber Piles
D 41-05 Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing
D 43-00 Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing
D 56-05 Test Method for Flash Point By Tag Closed Tester
D 86-05 Test Method for Distillation of Petroleum Products at Atmospheric Pressure
D 93-02a Test Method for Flash Point By Pensky-Martens Closed Cup Tester
D 225-04 Specification for Asphalt Shingles (Organic Felt) Surfaced with Mineral Granules
D 226-05 Specification for Asphalt-saturated Organic Felt Used in Roofing and Waterproofing
D 227-03 Specification for Coal-tar-saturated Organic Felt Used in Roofing and Waterproofing
D 312-00 Specification for Asphalt Used in Roofing
D 422-63(2002) Test Method for Particle-size Analysis of Soils
D 450-96(2006) Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing
D 635-06 Test Method for Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastics in a Horizontal Position
D 1143-81(1994)E01 Test Method for Piles Under Static Axial Compressive Load
D 1227-00 Specification for Emulsified Asphalt Used as a Protective Coating for Roofing
D 1557-02e1 Test Method for Laboratory Compaction Characteristics of Soil Using Modified Effort [56,000 ft-lb/ft3 (2,700 KN m/m3)]
D 1586-99 Specification for Penetration Test and Split-barrel Sampling of Soils
D 1761-06 Test Method for Mechanical Fasteners in Wood
D 1863-05 Specification for Mineral Aggregate Used on Built-up Roofs
D 1929-96(2001)e01 Test Method for Determining Ignition Properties of Plastics
D 1970-01 Specification for Self-adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roof Underlayment for Ice Dam Protection
D 2166-00e1 Test Method for Unconfined Compressive Strength of Cohesive Soil
D 2178-04 Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
D 2216-05 Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
D 2487-06 Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
D 2626-04 Specification for Asphalt Saturated and Coated Organic Felt Base Sheet Used in Roofing
D 2822-05 Specification for Asphalt Roof Cement
D 2823-05 Specification for Asphalt Roof Coatings
D 2843-99 (2004)e1 Test for Density of Smoke from the Burning or Decomposition of Plastics
D 2850-03a Test Method for Unconsolidated, Undrained Triaxial Compression Test on Cohesive Soils
D 2898-94(2004) Test Methods for Accelerated Weathering of Fire- Retardant-Treated Wood for Fire Testing
D 3019-301 (supp) Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and Nonasbestos Fibered
D 3161-05 Test Method for a Wind Resistance of Asphalt Shingles (Fan Induced Method)
D 3200-74(2005) Standard Specification and Test Method for Establishing Recommended Design Stresses for Round Timber Construction Poles
D 3201-94(2003) Test Method for Hygroscopic Properties of Fire-retardanttreated Wood and Wood-based Products
D 3278-96(2004)e01 Test Methods for Flash Point of Liquids by Small Scale Closed-cup Apparatus
D 3462-05 Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
D 3468-99(2006)e1 Specification for Liquid-applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing
D 3679-05 Specification for Rigid Poly [Vinyl Chloride (PVC) Siding]
D 3689-90(1995) Method for Testing Individual Piles Under Static Axial Tensile Load
D 3737-05 Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
D 3746-85(2002) Test Method for Impact Resistance of Bituminous Roofing Systems
D 3747-79 (2000e01) Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation
D 3909-97b(2004)e1 Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
D 3957-06 Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings
D 4022-94 (2000)e01 Specification for Coal Tar Roof Cement, Asbestos Containing
D 4272-03 Test Method for Total Energy Impact of Plastic Films by Dart Drop
D 4318-05 Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils
D 4434-04 Specification for Poly (Vinyl Chloride) Sheet Roofing
D 4479-00 Specification for Asphalt Roof Coatings-Asbestos-free
D 4586-00 Specification for Asphalt Roof Cement, Asbestos-free
D 4601-04 Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing
D 4637-04 Specification for EPDM Sheet Used in Single-ply Roof Membrane
D 4829-03 Test Method for Expansion Index of Soils
D 4869-05e1 Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing
D 4897-01 Specification for Asphalt-coated Glass Fiber Venting Base Sheet Used in Roofing
D 4945-00 Test Method for High-strain Dynamic Testing of Piles
D 4990-97a(2005)e1 Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing
D 5019-05 Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane
D5055-05 Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists
D5456-06 Specification for Evaluation of Structural Composite Lumber Products
D5516-03 Test Method of Evaluating the Flexural Properties of Fireretardant- treated Softwood Plywood Exposed to the Elevated Temperatures
D5643-94 (2000)e01 Specification for Coal Tar Roof Cement, Asbestos-free
D5664-02 Test Methods for Evaluating the Effects of Fire-retardant Treatment and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber
D5665-99a Specification for Thermoplastic Fabrics Used in Coldapplied Roofing and Waterproofing
D5726-98(2005) Specification for Thermoplastic Fabrics Used in Hotapplied Roofing and Waterproofing
D6083-05e1 Specification for Liquid Applied Acrylic Coating Used in Roofing
D6162-00A Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
D6163-00 E01 Specification for Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements
D6164-05 Specification for Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheet Metal Materials Using Polyester Reinforcements
D6222-02e1 Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements
D6223-02e1 Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
D6298-05 Specification for Fiberglass Reinforced Styrene-Butadiene- Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface
D6305-02e01 Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing
D6380-03 Standard Specification for Asphalt Roll Roofing (Organic) Felt
D6381-03b Standard Test Method for Measurement of Asphalt Shingle Mechanical Uplift Resistance
D6694-01 Standard Specification for Liquid-applied Silicone Coating Used in Spray Polyurethane Foam Roofing
D6754-02 Standard Specification for Ketone Ethylene Ester Based Sheet Roofing
D6757-05 Standard Specification for Inorganic Underlayment for Use with Steep Slope Roofing Products
D6841-03 Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant-treated Lumber
D6878-03 Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing
E 72-05 Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
E 84-06 Test Methods for Surface Burning Characteristics of Building Materials
E 90-04 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
E 96/E96M-05 Test Method for Water Vapor Transmission of Materials
E 108-05 Test Methods for Fire Tests of Roof Coverings
E 119-05 Test Methods for Fire Tests of Building Construction and Materials
E 136-04 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C
E 328-02 Methods for Stress Relaxation for Materials and Structures
E 330-02 Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference
E 331-00 Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference
E 492-04 Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-ceiling Assemblies Using the Tapping Machine
E 518-03 Standard Test Methods for Flexural Bond Strength of Masonry
E 519-02 Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages
E 605-93(2006) Test Method for Thickness and Density of Sprayed Fireresistive Material (SFRM) Applied to Structural Members
E 681-04 Test Methods for Concentration Limits of Flammability of Chemical Vapors and Gases
E736-00(2006) Test Method for Cohesion/Adhesion of Sprayed Fireresistive Materials Applied to Structural Members
E 814-02 Test Method of Fire Tests of Through-penetration Firestops
E 970-00 Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
E1300-04e01 Practice for Determining Load Resistance of Glass in Buildings
E1592-05 Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
E1602-03 Guide for Construction of Solid Fuel-burning Masonry Heaters
E1886-05 Test Method for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Missiles and exposed to Cyclic Pressure Differentials
E1966-01 Test Method for Fire-resistant Joint Systems
E1996-05 Specification for Performance of Exterior Windows, Glazed Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
E 2307-04e1 Standard Test Method for Determining Fire Resistance of Perimeter Fire Barrier Systems Using Intermediate-scale, Multistory Test Apparatus
F 547-01 Terminology of Nails for Use with Wood and Wood-based Materials
F1346-91(2003) Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs
F1667-05 Specification for Driven Fasteners: Nails, Spikes and Staples
F2006-00(2005) Standard/Safety Specification for Window Fall Prevention Devices for Nonemergency Escape (Egress) and Rescue (Ingress) Windows
F2090-01a Specification for Window Fall Prevention Devices with Emergency Escape (Egress) Release Mechanisms
G 152-06 Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
G 154-05 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
G 155-05a Practice for Operating Xenon Arc Light Apparatus for Exposure of Nonmetallic Materials
The Association of the Wall and Ceiling Industries International
803 West Broad Street, Suite 600
Falls Church, VA 22046
AWCI
Standard reference number Title
12-B-98 Technical Manual 12-B Standard Practice for the Testing and Inspection of Field Applied This-Film Intumescent Fire-resistive Materials; an Annotated Guide, First Edition
American Wood-Preservers’ Association
P.O. Box 5690
Grandbury, TX 76049
AWPA
Standard reference number Title
C1-00 All Timber Products-Preservative Treatment by Pressure Processes
M4-02 Standard for the Care of Preservative-treated Wood Products
U1-04 USE CATEGORY SYSTEM: User Specification for Treated Wood Except Section 6, Commodity Specification H
American Welding Society
550 N.W. LeJeune Road
Miami, FL 33126
AWS
Standard reference number Title
D1.1/D1.1M-06 Structural Welding Code-Steel
D1.3-98 Structural Welding Code-Sheet Steel
D1.4/D1.4M-05 Structural Welding Code-Reinforcing Steel
Builders Hardware Manufacturers’ Association
355 Lexington Avenue, 17th Floor
New York, NY 10017-6603
BHMA
Standard reference number Title
A 156.10-05 American National Standard for Power Operated Pedestrian Doors
A 156.19-02 Standard for Power Assist and Low Energy Operated Doors
Canadian General Standards Board
222 Queens Street
14th Floor, Suite 1402
Ottawa, Ontario, Canada KIA 1G6
CGSB
Standard Reference Number Title
CAN/CGSB 37.54-95 Polyvinyl Chloride Roofing and Waterproofing Membrane
37-GP-56M (1980) Membrane, Modified, Bituminous, Prefabricated and Reinforced for Roofing-with December 1985 Amendment
Consumer Product Safety Commission
4330 East West Highway
Bethesada, MD 20814-4408
CPSC
Standard reference number Title
16 CFR Part 1201(1977) Safety Standard for Architectural Glazing Material
16 CFR Part 1209 (1979) Interim Safety Standard for Cellulose Insulation
16 CFR Part 1404 (1979) Cellulose Insulation
16 CFR Part 1500 (1991) Hazardous Substances and Articles; Administration and Enforcement Regulations
16 CFR Part 1500.44 (2001) Method for Determining Extremely Flammable and Flammable Solids
16 CFR Part 1507 (2001) Fireworks Devices
16 CFR Part 1630 (2000) Standard for the Surface Flammability of Carpets and Rugs
Canadian Standards Association
5060 Spectrum Way, Suite 100
Mississauga, Ontario, L4W 5N6 Canada
CSA
Standard reference number Title
101/I.S.2/A440-05 Specifications for Windows, Doors and Unit Skylights CPSC*
*Note: Also see AAMA and WDMA
Cedar Shake and Shingle Bureau
P.O. Box 1178
Sumas, WA 98295-1178
CSSB
Standard reference number Title
CSSB-97 Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau
Door and Access Systems Manufacturers Association International
1300 Summer Avenue
Cleveland, OH 44115-2851
DASMA
Standard reference number Title
107-97 Room Fire Test Standard for Garage Doors Using Foam Plastic Insulation
U.S. Department of Housing and Urban Development
c/o Superintendent of Documents
U.S. Government Printing Office
Washington, DC 20402-9325
DOHUD
Standard Reference Number Title
“24 CFR Part 3280 (2000),” “Manufactured Home Construction and Safety Standards”
U.S. Department of Commerce
National Institute of Standards and Technology
100 Bureau Drive Stop 3460
Gaithersburg, MD 20899
DOC
Standard reference number Title
PS-1-95 Construction and Industrial Plywood
PS-2-92 Performance Standard for Wood-based Structural-use Panels
PS 20-99 American Softwood Lumber Standard U.S. Department of Labor
c/o Superintendent of Documents
U.S. Government Printing Office
Washington, DC 20402-9325
DOL
Standard reference number Title
29 CFR Part 1910.1000 Air Contaminants
(1974)
U.S. Department of Transportation
c/o Superintendent of Documents
U.S. Government Printing Office
Washington, DC 20402-9325
DOTn
Standard reference number Title
49 CFR-1998 Specification of Transportation of Explosive and Other Dangerous Articles, UN 0335,UN 0336
Shipping Containers
49 CFR Parts 173.137
(1990) Shippers-General Requirements for Shipments and Packaging-Class 8-Assignment of Packing Group
Federal Emergency Management Agency
Federal Center Plaza
500 C Street S.W.
Washington, DC 20472
FEMA
Standard reference number Title
FIA-TB 11-01 Crawlspace Construction for Buildings Located in Special Flood Hazard Areas
44 CFR parts 59-77
Factory Mutual
Standards Laboratories Department
1151 Boston-Providence Turnpike
Norwood, MA 02062
FM
Standard reference number Title
4450 (1989) Approval Standard for Class 1 Insulated Steel Deck Roofswith Supplements through July 1992
4470 (1992) Approval Standard for Class 1 Roof Covers
4880 (2001) American National Standard for Evaluating Insulated Wall or Wall and Roof/Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels, Wall/Ceiling Coating Systems, Interior and Exterior Finish Systems
Gypsum Association
810 First Street N.E. #510
Washington, DC 20002-4268
GA
Standard reference number Title
GA 216-04 Application and Finishing of Gypsum Board
GA 600-06 Fire-Resistance Design Manual, 18th Edition
Hardwood Plywood Veneer Association
1825 Michael Faraday Drive
Reston, VA 20190-5350
HPVA
Standard reference number Title
HP-1-2004 The American National Standard for Hardwood and Decorative Plywood
International Code Council
5203 Leesburg Pike, Suite 600
Falls Church, VA 22041
ICC
Standard reference number Title
ICC/ANSI A117.1-03 Accessible and Usable Buildings and Facilities
ICC 300-02 ICC Standard on Bleachers, Folding and Telescopic Seating and Grandstands
IECC-06 International Energy Conservation CodeŽ
IFC-06 International Fire CodeŽ
IFGC-06 International Fuel Gas CodeŽ
International Standards Organization
ISO Central Secretariat1, rue de Varembee, Case postale 56
CH-1211 Geneva 20, Switzerland
ISO
Standard reference number Title
ISO 8115-86 Cotton Bales-Dimensions and Density
National Association of Architectural Metal Manufacturers
8 South Michigan Ave
Chicago, IL 60603
NAAMM
Standard reference number Title
FP 1001-97 Guide Specifications for Design of Metal Flag Poles
National Concrete Masonry Association
2302 Horse Pen Road
Herndon, VA 22071-3499
NCMA
Standard reference number Title
TEK 05-08(1996) Details for Concrete Masonry Fire Walls
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269-9101
NFPA
Standard reference number Title
11-05 Low Expansion Foam
12-05 Carbon Dioxide Extinguishing Systems
12A-04 Halon 1301 Fire Extinguishing Systems
13-07 Installation of Sprinkler Systems
13D-07 Installation of Sprinkler Systems in One- and Two-family Dwellings and Manufactured Homes
13R-07 Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height
14-07 Installation of Standpipe and Hose System
16-03 Installation Foam-water Sprinkler and Foam-water Spray Systems
17-02 Dry Chemical Extinguishing Systems
17A-02 Wet Chemical Extinguishing Systems
20-07 Installation of Stationary Pumps for Fire Protection
30-03 Flammable and Combustible Liquids Code
31-06 Installation of Oil-burning Equipment
32-04 Dry Cleaning Plants
40-01 Storage and Handling of Cellulose Nitrate Film
61-02 Prevention of Fires and Dust Explosions in Agricultural and Food Product Facilities
70-08 National Electrical Code
72-07 National Fire Alarm Code
80-99 Fire Doors and Fire Windows
85-04 Boiler and Combustion System Hazards Code (Note: NFPA 8503 has been incorporated into NFPA 85)
92B-05 Smoke Management Systems in Malls, Atria and Large Spaces
105-03 Standard for the Installation of Smoke Door Assemblies
110-05 Emergency and Standby Power Systems
111-01 Stored Electrical Energy Emergency and Standby Power Systems
120-04 Coal Preparation Plants
211-06 Chimneys, Fireplaces, Vents and Solid Fuel-burning Appliances
230-03 Standard for the Fire Protection of Storage
252-03 Standard Methods of Fire Tests of Door Assemblies
253-05 Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source
257-00 Standard for Fire Test for Window and Glass Block Assemblies
259-03 Test Method for Potential Heat of Building Materials
265-07 Method of Fire Tests for Evaluating Room Fire Growth Contribution of Textile Wall Coverings on Full Height Panels and Walls
268-01 Standard Test Method for Determining Ignitibility of Exterior Wall Assemblies Using a Radiant Heat Energy Source
285-05 Standard Method of Test for the Evaluation of Flammability Characteristics of Exterior Nonload-bearing Wall Assemblies Containing Combustible Components
286-05 Standard Method of Fire Test for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth
288-01 Standard Methods of Fire Tests of Floor Fire Door Assemblies in Fire-resistance-rated Floor Systems
303-05 Fire Protection Standards for Marinas and Boatyards
409-04 Aircraft Hangars
418-06 Standard for Heliports
484-06 Standard for Combustible Metals
654-05 Prevention of Fire & Dust Explosions from the Manufacturing, Processing and Handling of Combustible Particulate Solids
655-01 Prevention of Sulfur Fires and Explosions
664-02 Prevention of Fires Explosions in Wood Processing and Woodworking Facilities
701-04 Standard Methods of Fire Tests for Flame-propagation of Textiles and Films
704-01 Standard System for the Identification of the Hazards of Materials for Emergency Response 1124-03 Manufacture, Transportation, and Storage of Fireworks and Pyrotechnic Articles
1124-05 Manufacture, Transportation, and Storage of Fireworks and Pyrotechnic Articles
2001-04 Clean Agent Fire Extinguishing Systems
Precast Prestressed Concrete Institute
175 W. Jackson Boulevard, Suite 1859
Chicago, IL 60604-9773
PCI
Standard reference number Title
MNL 124-89 Design for Fire Resistance of Precast Prestressed Concrete
MNL 128-01 Recommended Practice for Glass Fiber Reinforced Concrete Panels
Post-Tensioning Institute
1717 W. Northern Avenue, Suite 114
Phoenix, AZ 85021
PTI
Standard reference number Title
PTI-2004 Standard Requirements for Analysis of Shallow Concrete Foundations on Expansive Soils, First Edition
PTI-2004 Standard Requirements for Design of Shallow Post-tensioned Concrete Foundation on Expansive Soils
Rack Manufacturers Institute
8720 Red Oak Boulevard, Suite 201
Charlotte, NC 28217
RMI
Standard reference number Title
ANSI MH 16.1-2004 Specification for Design, Testing and Utilization of Industrial Steel Storage Racks (formerly RMI 2002)
Steel Joist Institute
3127 10th Avenue, North
Myrtle Beach, SC 29577-6760
SJI
Standard reference number Title
JG-1.1-05 Standard Specification for Joist Girders
K-1.1-05 Standard Specification for Open Web Steel Joists, K-Series
LH/DLH-1.1-05 Standard Specification for Longspan Steel Joists, LH Series and Deep Longspan Steel Joists, DLH Series
Single-Ply Roofing Institute
77 Rumford Ave.
Suite 3-B
Walthem, MA 02453
SPRI
Standard reference number Title
ES-1-03 Wind Design Standard for Edge Systems Used with Low Slope Roofing Systems
RP-4-02 Wind Design Guide for Ballasted Single-ply Roofing Systems
Telecommunications Industry Association
2500 Wilson Boulevard
Arlington, VA 22201-3834
TIA
Standard reference number Title
TIA/EIA-222-G-05 Structural Standards for Steel Antenna Towers and Antenna Supporting Structures
The Masonry Society
3970 Broadway, Unit 201-D
Boulder, CO 80304-1135
TMS
Standard reference number Title
0216-97 Standard Method for Determining Fire Resistance of Concrete and Masonry Construction Assemblies
402-05 Building Code Requirements for Masonry Structures
602-05 Specification for Masonry Structures
Truss Plate Institute
583 D’Onofrio Drive, Suite 200
Madison, WI 53719
TPI
Standard reference number Title
TPI 1-2002 National Design Standards for Metal-plate-connected Wood Truss Construction
Underwriters Laboratories, Inc.
333 Pfingsten Road
Northbrook, IL 60062-2096
UL
Standard reference number Title
10A-98 Tin Clad Fire Doors-with Revisions through March 2003
10B-97 Fire Tests of Door Assemblies-with Revisions through October 2001
10C-98 Positive Pressure Fire Tests of Door Assemblies-with Revisions through November 2001
14B-98 Sliding Hardware for Standard Horizontally Mounted Tin Clad Fire Doors-with Revisions through July 2000
14C-99 Swinging Hardware for Standard Tin Clad Fire Doors Mounted Singly and in Pairs
94-96 Test for Flammability of Plastic Materials for Parts in Devices and Appliances
103-01 Factory-built Chimneys, for Residential Type and Building Heating Appliances
127-99 Factory-built Fireplaces-with Revisions through November1999
199E-04 Outline of Investigation for Fire Testing of Sprinklers and Water Spray Nozzles for Protection of Deep Fat Fryers
217-97 Single and Multiple Station Smoke Alarms-with revisions through January 2004
268-96 Smoke Detectors for Fire Protective Signaling Systems-with Revisions through January 1999
300-05 Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas -with Revisions through December 1998
555-06 Fire Dampers-with Revisions through January 2002
555C-96 Ceiling Dampers
555S-99 Smoke Dampers-with Revisions through January 2002
580-94 Test for Uplift Resistance of Roof Assemblies-with Revisions through February 1998
641-95 Type L Low-temperature Venting Systems-with Revisions through April 1999
710B-2004 Recirculating Systems
790-04 Tests for Fire Resistance of Roof Covering Materials-with Revisions through July 1998
793-03 Standards for Automatically Operated Roof Vents for Smoke and Heat
864-03 Standards For Control Units and Accessories for Fire Alarm Signaling Systems-with Revisions through October 2003
1040-96 Fire Test of Insulated Wall Construction-with Revisions through April 2001
1256-02 Fire Test of Roof Deck Construction
1479-03 Fire Tests of Through-penetration Fire stops-with Revisions through August 2000
1482-98 Solid-fuel Type Room Heater-with Revisions through January 2000
1715-97 Fire Test of Interior Finish Material-with Revisions through October 2002
1777-04 Chimney Liners-with Revisions through July 1998
1784-01 Air Leakage Tests of Door Assemblies
1897-04 Uplift Tests for Roof Covering Systems-with Revisions through November 2002
1975-96 Fire Test of Foamed Plastics Used for Decorative Purposes
2017-2000 Standards for General-purpose Signaling Devices and Systems- with Revisions through June 2004
2079-04 Tests for Fire Resistance of Building Joint Systems
2200-98 Stationary Engine Generator Assemblies (Revisions through July 2004)
2390-04 Test Method for Measuring the Wind Uplift Coefficients for Asphalt Shingles
Underwriters Laboratories of Canada
7 Crouse Road
Scarborough, Ontario, Canada M1R3A9
ULC
Standard reference number Title
CAN/ULC S102.2-03 Standard Method of Test for Surface Burning Characteristics of Flooring, Floor Coverings and Miscellaneous Materials and Assemblies with 2000 Revisions
United States Code
c/o Superintendent of Documents
U.S. Government Printing Office
Washington, DC 20402-9325
USC
Standard reference number Title
10 U.S.C. Sections 18233(A)(1) and 18237-1994
18 USC Part 1, Ch.40 Importation, Manufacture, Distribution and Storage of Explosive Materials
Window and Door Manufacturers Association
1400 East Touhy Avenue #470
Des Plaines, IL 60018
WDMA
Standard reference number Title
101/I.S.2/A440-05 Specifications for Windows, Doors and Unit Skylights*
*Note: Also see AAMA and CSA
Wire Reinforcement Institute, Inc.
203 Loudon Street, S.W.
2nd Floor, Suite 203C
Leesburg, VA 22075
WRI
Standard reference number Title
WRI/CRSI-81 Design of Slab-on-ground Foundations-with 1996 Update
Effective: 01/01/2009
R.C. 119.032 review dates: 07/01/2012
Promulgated Under: 119.03
Statutory Authority: 3781.10(A)
Rule Amplifies: 3781.10, 3781.11, 3791.04
Prior Effective Dates: 9/1/92, 2/1/93, 7/1/95, 7/1/97, 3/1/98, 7/1/98, 1/1/99, 12/1/00, 1/1/02, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08