Chapter 4101:2-15 Referenced standards

4101:2-15-01 [Effective until 11/1/2017] Referenced standards.

1501.1 General. This chapter lists the codes and standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and the title. The application of the referenced standards shall be as specified in Section 102.5 of the building code.

1501.2 Referenced codes:When indicated in the OMC, the following codes refer to provisions in the listed chapters of the Administrative Code:

Referenced code

Ohio Administrative Code chapters

Building Code

4101:1-1 to 4101:1-35

Fire Code

1301:7-1 to 1301:7-7

Ohio Boiler and Pressure Vessel Rules

4101:4-1 to 4101:4-10

Plumbing Code

4101:3-1 to 4101:3-13

1501.3 Referenced Standards.

ACCA Air Conditioning Contractors of America

2800 Shirlington Road, Suite 300

Arlington, VA 22206

Standard reference number

Title

Manual D-95

183-2007

Residential Duct Systems

Peak Cooling and Heating Load Calculations in Buildings Except Low-Rise Residential Buildings

AHRI Air-Conditioning, Heating and Refrigeration Institute

4100 North Fairfax Drive, Suite 200

Arlington, VA 22203

Standard reference number

Title

700-06

Purity Specifications for Fluorocarbon and Other Refrigerants

ANSIAmerican National Standards Institute

11 West 42nd Street

New York, NY 10036

Standard reference number

Title

Z 21.8 -1994 (R2002)

Installation of Domestic Gas Conversion Burners

ASHRAE American Society of Heating, Refrigerating and Air-Conditioning

Engineers, Inc.

1791 Tullie Circle, NE

Atlanta, GA 30329

Standard reference number

Title

Handbook- 2009

ASHRAE Fundamentals Handbook-

15-2010

Safety Standard for Refrigeration Systems

34-2010

Designation and Safety Classification of Refrigerants

62.1 -2010

Ventilation for Acceptable Indoor Air Quality

62.2.-2010

Ventilation for Acceptable Indoor Air Quality in Low-Rise Residential Buildings

170-2008

Ventilation of Health Care Facilities (with addendums a through h-2011)

ASME American Society of Mechanical Engineers

Three Park Avenue

New York, NY 10016-5990

Standard reference number

Title

B1.20.1-1983 (R2006)

Pipe Threads, General Purpose (Inch

B 16.3 -2006

Malleable Iron Threaded Fittings, Classes 150 & 300

B 16.5 -2009

Pipe Flanges and Flanged Fittings NPS 1/2 through NPS 24-.

B 16.9 -2007

Factory Made Wrought Steel Buttwelding Fittings

B 16.11 -2009

Forged Fittings, Socket-welding and Threaded

B 16.15 -2006

Cast Bronze Threaded Fittings

B 16.18 -2001 (Reaffirmed 2005)

Cast Copper Alloy Solder Joint Pressure Fittings

B 16.22 -2001 (Reaffirmed 2005)

Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

B 16.23 -2002 (Reaffirmed 2006)

Cast Copper Alloy Solder Joint Drainage Fittings DWV

B 16.24 -2006

Cast Copper Alloy Pipe Flanges and Flanged Fittings: Class 150, 300, 400, 600, 900, 1500 and

B 16.26 -2006

Cast Copper Alloy Fittings for Flared Copper Tubes

B 16.28 -1994

Wrought Steel Buttwelding Short Radius Elbows and Returns

B 16.29 -2007

Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings-

B 31.9 -2010

Building Services Piping

BPVC-2010

Boiler & Pressure Vessel Code

BPVC Section IX-2010

Welding and Brazing Qualifications

CSD-1-2009

Controls and Safety Devices for Automatically Fired Boilers

ASSEAmerican Society of Sanitary Engineering

901 Canterbury, Suite A

Westlake, OH 44145

Standard reference number

Title

1017-09

Temperature Actuated Mixing Valves for Hot Water Distribution Systems

ASTMASTM International

100 Barr Harbor Drive

West Conshohocken, PA 19428

Standard reference number

Title

A 53/A 53M-10

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

A 106/A106M-10

Specification for Seamless Carbon Steel Pipe for High-Temperature Service

A 126-04 (2009)

Specification for Gray Iron Castings for Valves, Flanges and Pipe Fittings

A 254-97 (2007)

Specification for Copper Brazed Steel Tubing

A 420/A 420M-10

Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service

A 539-99

Specification for Electric-Resistance-Welded Coiled Steel Tubing for Gas and Fuel Oil Lines

B 32-08

Specification for Solder Metal

B 42-10

Specification for Seamless Copper Pipe, Standard Sizes

B 43-09

Specification for Seamless Red Brass Pipe, Standard

B 68-02

Specification for Seamless Copper Tube, Bright Annealed

B 75-02

Specification for Seamless Copper

B 88-09

Specification for Seamless Copper Water

B 135-10

Specification for Seamless Brass Tube

B 251-10

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

B 280-08

Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service

B 302-07

Specification for Threadless Copper Pipe, Standard

B 813-10

Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube

C 315-07

Specification for Clay Flue Liners and Chimney Pots

C 411-05

Test Method for Hot-surface Performance of High-temperature Thermal Insulation

D 56-05 (2010)

Test Method for Flash Point by Tag Closed Tester

D 93-10a

Test Method for Flash Point of Pensky-Martens Closed Cup Tester

D 1527-99(2005)

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

D 1693-08

Test Method for Environmental Stress-Cracking of Ethylene Plastics

D 1785-06

Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe, Schedules 40, 80 and 120

D 2235-04

Specifications for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

D 2241-09

Specification for Poly (Vinyl Chloride)(PVC) Pressure-rated Pipe (SDR-Series

D 2282-99(2005)

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)

D 2412-10

Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-plate Loading

D 2447-03

Specification for Polyethylene (PE) Plastic Pipe, Schedules 40 and 80, Based on Outside Diameter

D 2466-06

Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe Fittings, Schedule 40

D 2467-06

Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe Fittings, Schedule 80

D 2468-96a

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40

D 2513-09a

Specification for Thermoplastic Gas Pressure Pipe, Tubing, and

D 2564-04(2009)e01

Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

D 2657-07

Standard Practice for Heat Fusion Joining ofPolyolefin Pipe and Fittings

D 2683-10

Specification for Socket-type Polyethylene Fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

D 2837-08

Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

D 2846/D 2846M-09b

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot and Cold Water Distribution Systems

D 2996-01(2007)e01

Specification for Filament-wound Fiberglass (Glass Fiber Reinforced Thermosetting Resin) Pipe

D 3035-08

Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

D 3278-96(2004)e01

Test Methods for Flash Point of Liquids by Small Scale Closed-cup Apparatus

D 3261-10a

Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and

D 3309-96a(2002)

Specification for Polybutylene (PB) Plastic Hot and Cold Water Distribution Systems

D 3350-10

Specification for Polyethylene Plastics Pipe and Fittings Materials

E 84-10b

Test Method for Surface Burning Characteristics of Building Materials

E 119-10b

Test Method for Fire Tests of Building Construction and

E 136-09b

Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 Degrees C

E 814-10

Test Method for Fire Tests of Through-penetration Fire

E 1509-04

Specification for Room Heaters, Pellet Fuel-burning

E 2231-09

Standard Practice For Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics

E 2336-04 (2009)

Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems

F 438-09

Specification for Socket Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

F 439-09

Specification for Socket Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 441/F 441M-09

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and

F 442/F 442M-09

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR).

F 493-10

Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

F 876- 10

Specification forCrosslinkedPolyethylene (PEX) Tubing

F 877-07

Specification for Crosslinked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems.

F 1055-98(2006)

Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and

F 1281-07

Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe

F 1282-10

Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

F 1476-07

Specification for Performance of Gasketed Mechanical Couplings for

  

Use in Piping Applications

F 1924-05

Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

F 1974-09

Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe

F 2389-10

Specification for Pressure-Rated Polypropylene Piping Systems

F 2623-08

Standard Specification for Polyethylene of Raised Temperature (PERT) SDR 9 Tubing1

AWSAmerican Welding Society

550 N.W. LeJeune Road P.O. Box 351040

Miami, FL 33135

Standard reference number

Title

A 5.8 -2004

Specifications for Filler Metals for Brazing and Braze Welding.

AWWAAmerican Water Work Association

6666 West Quincy Avenue

Denver, CO 80235

Standard reference number

Title

C110/A 21.10 -08

Standard for Ductile Iron & Gray Iron Fittings, 2 inches Through 48 inches for Water

C115/A 21.15 -05

Standard for Flanged Ductile-iron Pipe with Ductile Iron or Grey-iron Threaded Flanges

C151/A 21.51 -09

Standard for Ductile-Iron Pipe, Centrifugally Cast for Water

C153/A 21.53 -06

Standard for Ductile-Iron Compact Fittings for Water Service

CSACanadian Standards Association

5060 Spectrum Way Mississauga,

Ontario, Canada L4W 5N6

Standard reference number

Title

B 137.9 -M91 CAN/CSA

Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure-Pipe Systems

B 137.10 - 05

Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure-Pipe Systems

ANSI CSA America FC1- 04

Stationary Fuel Cell Power Systems

DOLDepartment of Labor Occupational Safety and Health Administration

c/o Superintendent of Documents

US Government Printing Office

Washington, DC 20402-9325

Standard reference number

Title

29 CFR Part 1910.1000(1974)

Air Contaminants

29 CFR Part 1910. 1025

Toxic and Hazardous Substances

FSFederal Specifications*

General Services Administration

7th & D Streets Specification Section, Room 6039

Washington, DC 20407

Standard reference number

Title

WW-P-325B (1976)

Pipe, Bends, Traps, Caps and Plugs; Lead (for Industrial Pressure and Soil and Waste Applications

*Standards are available from the Supt. of Documents, U.S. Government Printing Office, Washington, DC 20402-9325.

ICCInternational Code Council, Inc.

500 New Jersey Ave, NW

6th Floor ICC

Washington, DC 20001

Standard reference number

Title

IFGC-09

International Fuel Gas Code (including ICC Emergency Amendment changing IFGC Sections 406.7 )

IIAR International Institute of Ammonia Refrigeration

1110 North Glebe Road

Arlington, VA 22201

Standard reference number

Title

2-99 (with Addendum A-2005)

Equipment, Design, and Installation of Ammonia Mechanical Refrigerating Systems

MSSManufacturers Standardization Society of the Valve & Fittings Industry, Inc. 1

27 Park Street, N.E.

Vienna, VA 22180

Standard reference number

Title

SP-69-2003

Pipe Hangers and Supports-Selection and Application

NAIMANorth American Insulation Manufacturers Association

44 Canal Center Plaza, Suite 310 Alexandria, VA 22314

Standard reference number

Title

AH116-02

Fibrous Glass Duct Construction Standards

NFPANational Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

Standard reference number

Title

30-15

Flammable and Combustible Liquids Code

30A-08

Code for Motor Fuel-dispensing Facilities and Repair Garages

31- 11

Installation of Oil-burning Equipment

37- 10

Stationary Combustion Engines and Gas Turbines

58- 11

Liquefied Petroleum Gas Code

69-08

Explosion Prevention Systems

70- 14

National Electrical Code

72- 10

National Fire Alarm and Signaling Code (including TIA 10-4 and TIA 10-5)

75-09

Protection of Information Technology Equipment

82- 09

Incinerators and Waste and Linen Handling Systems and Equipment

85-07

Boiler and Combustion Systems Hazards Code

91- 10

Exhaust Systems for Air Conveying of Vapors, Gases, and Noncombustible Particulate Solids

92B- 09

Smoke Management Systems in Malls, Atria and Large Spaces

96-14

Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations

211- 10

Chimneys, Fireplaces, Vents and Solid Fuel-burning Appliances

262-07

Standard Method of Test for Flame Travel and Smoke of Wires and Cables for Use in Air-handling Spaces

704-07

Identification of the Hazards of Materials for Emergency Response

853- 10

Installation of Stationary Fuel Power Plants

SMACNASheet Metal & Air Conditioning Contractors National Assoc., Inc.

4201 Lafayette Center Drive

Chantilly, VA 20151-1209

Standard reference number

Title

SMACNA/ANSI-2005

SMACNA-03

HVAC Duct Construction Standards-Metal and Flexible (2005)

Fibrous Glass Duct Construction Standards

ULUnderwriters Laboratories, Inc.

333 Pfingsten Road

Northbrook, IL 60062-2096

Standard reference number

Title

17- 08

Vent or Chimney Connector Dampers for Oil-fired Appliances

103- 10

Factory-built Chimneys, Residential Type and Building Heating Appliance

127- 08

Factory-built Fireplaces

174-04

Household Electric Storage Tank Water Heaters-with Revisions through May 2006

181-05

Factory-made Air Ducts and Air Connectors-with Revisions through December 1998

181A-05

Closure Systems for Use with Rigid Air Ducts and Air Connectors- with Revisions through December 1998

181B-05

Closure Systems for Use with Flexible Air Ducts and Air Connectors- with Revisions through December 1998

207-01

Refrigerant-containing Components and Accessories, Nonelectrical- with Revisions through November 2004

263-03

Standard for Fire Test of Building Construction and Materials

268- 09

Smoke Detectors for Fire Prevention Signaling Systems

268A- 08

Smoke Detectors for Duct Applications

343- 08

Pumps for Oil-Burning Appliances

391- 10

Solid-fuel and Combination-fuel Central and Supplementary Furnaces

412-04

Refrigeration Unit Coolers-with Revisions through February 2007 .

471- 10

Commercial Refrigerators and Freezers

508-99

Industrial Control Equipment-with Revisions through July 2005

536-97

Flexible Metallic Hose-with Revisions through June 2003

555-06

Fire Dampers-with Revisions through January 2002.

555C-06

Ceiling Dampers

555S-99

Smoke Dampers-with Revisions through July 2006

586- 09

High-efficiency, Particulate, Air Filter Units

641-95

Type L Low-temperature Venting Systems-with Revisions through August 2005

710-95

Exhaust Hoods for Commercial Cooking Equipment-with Revisions through February 2007.

710B-04

Recirculating Systems

723- 08

Standard for Test for Surface Burning Characteristics of Building Materials

726-95

Oil-fired Boiler Assemblies-with Revisions through March 2006

727-06

Oil-fired Central Furnaces

729-03

Oil-fired Floor Furnaces-with Revisions through January 1999

730-03

Oil-fired Wall Furnaces-with Revisions through January 1999

731-95

Oil-fired Unit Heaters-with Revisions through February 2006

732-95

Oil-fired Storage Tank Water Heaters-with Revisions through February 2005

737- 07

Fireplace Stoves

762-03

Outline of Investigation for Power Ventilators for Restaurant Exhaust

  

Appliances

791-06

Residential Incinerators.

834-04

Heating, Water Supply and Power Boilers Electric-with Revisions through March 2006

858-05

Household Electric Ranges-with Revisions through April 2006

867-00

Electrostatic Air Cleaners-with Revisions through May 2004

875- 09

Electric Dry Bath Heater

896-93

Oil-burning Stoves-with Revisions through May 2004

900-04

Air Filter Units

923- 08

Microwave Cooking Appliances

959-01

Medium Heat Appliance Factory-built Chimneys-with Revisions through September 2006

1240-05

Electric Commercial Clothes

1261-01

Electric Water Heaters for Pools and Tubs-with Revisions through June 2004

1453-04

Electric Booster and Commercial Storage Tank Water Heaters-with Revisions through May 2006

1482- 10

Solid-fuel Type Room Heaters

1777- 07

Chimney Liners .

1812- 09

Standard for Ducted Heat Recovery Ventilators

1815- 09

Standard for Nonducted Heat Recovery Ventilators

1820-04

Fire Test of Pneumatic Tubing for Flame and Smoke Characteristics

1887-04

Fire Tests of Plastic Sprinkler Pipe for Visible Flame and Smoke Characteristics

1978- 05

Grease Ducts

1995-05

Heating and Cooling Equipment .

2085-10

Protected Above-Ground Tanks for Flammable and Combustible Liquids

2158-97

Electric Clothes Dryers-with Revisions through May 2004

2162-01

Outline of Investigation for Commercial Wood-fired Baking Ovens- Refractory Type

2200- 12

StationaryEngine Generator Assemblies

2221- 10

Tests of Fire Resistive Grease Duct Enclosure Assemblies

Cite as Ohio Admin. Code 4101:2-15-01

Effective: 1/1/2016
Five Year Review (FYR) Dates: 11/01/2016
Promulgated Under: 119.03
Statutory Authority: 3781.10(A)
Rule Amplifies: 3781.10 , 3781.11, 3791.04
Prior Effective Dates: 7/1/82, 3/1/85, 3/1/86, 1/1/89, 9/1/92, 7/1/95, 2/1/96, 3/1/98, 7/1/98, 1/1/02, 1/1/04, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08, 1/1/09, 11/1/11, 3/1/13, 1/1/15

4101:2-15-01 [Effective 11/1/2017] Referenced standards.

1501.1 General. This chapter lists the codes and standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and the title. The application of the referenced standards shall be as specified in Section 102.5 of the building code.

1501.2 Referenced codes: When indicated in the OMC, the following codes refer to provisions in the listed chapters of the Administrative Code:

Referenced code

Ohio Administrative Code chapters

Building Code

4101:1-1 to 4101:1-35

Fire Code

1301:7-1 to 1301:7-7

Ohio Boiler and Pressure Vessel Rules

4101:4-1 to 4101:4-10

Plumbing Code

4101:3-1 to 4101:3-15

1501.3 Referenced Standards.

ACCA Air Conditioning Contractors of America 2800 Shirlington Road, Suite 300 Arlington, VA 22206

Standard Referenced

Title

Manual D-2014 183-2007 (reaffirmed 2011)

Residential Duct Systems Peak Cooling and Heating Load Calculations in Buildings Except Low-rise Residential Buildings

AHRI Air-Conditioning, Heating and Refrigeration Institute

4100 North Fairfax Drive, Suite 200

Arlington, VA 22203

Standard Referenced

Title

700-2016

Purity Specifications for Fluorocarbon and

with Addendum 1

Other Refrigerants

AMCA Air Movement and Control Association International

30 West University Drive

Arlington Heights, IL 60004

Standard Referenced

Title

230-CD1

Laboratory Methods of Testing Air Circulating Fans for Rating and Certification

550-15

Test Method for High Velocity Wind Driven Rain Resistant Louvers

ANSI American National Standards Institute

11 West 42nd Street

New York, NY 10036

Standard Referenced

Title

Z 21.8 -1994 (R2012)

Installation of Domestic Gas Conversion Burners

ASHRAE American Society of Heating, Refrigerating and Air

-Conditioning Engineers

1791 Tullie Circle, NE

Atlanta, GA 30329

Standard Referenced

Title

Handbook-2013

15-2013

34-2013

ASHRAE Fundamentals Handbook

Safety Standard for Refrigeration Systems

Designation and Safety Classification of Refrigerants

62.1 -2016

Ventilation for Acceptable Indoor Air Quality

62.2 -2016

Ventilation and Acceptable Indoor Air

Quality in Low-Rise Residential Buildings

170-2013

Ventilation of Health Care Facilities

180-2012

Standard Practice for Inspection and

Maintenance of Commercial Building

HVAC Systems

ASME American Society of Mechanical Engineers

Three Park Avenue

New York, NY 10016-5990

Standard Referenced

Title

B1.20.1-2013

Pipe Threads, General Purpose (Inch)

B 16.3 -2011

Malleable Iron Threaded Fittings, Classes 150 & 300

B 16.5 -2013

Pipe Flanges and Flanged Fittings NPS ½ through NPS 24

B 16.9 -2012

Factory Made Wrought Steel Buttwelding Fittings

B 16.11 -2011

Forged Fittings, Socket-welding and Threaded

B 16.15 -2013

Cast Bronze Threaded Fittings

B 16.18 -2012

Cast Copper Alloy Solder Joint Pressure Fittings

B 16.22 -2-13

Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

B 16.24 -2011

Cast Copper Alloy Pipe Flanges and Flanged Fittings: Class 150, 300, 400, 600, 900, 1500 and 2500

B 16.26 -2013

Cast Copper Alloy Fittings for Flared Copper Tubes

B 16.28 -1994

Wrought Steel Buttwelding Short Radius Elbows and Returns

B 16.51 -2013

Copper and Copper Alloy Press-Connect Pressure Fittings

B 31.5 -2016

Refrigeration Piping and Heat Transfer Components

B 31.9 -2014

BPVC- the edition referenced in rule 4101:4-3-01 of the Administrative Code CSD-1-the edition referenced

in rule 4101:4-3-01 of the

Administrative Code

Building Services Piping

ASME Boiler & Pressure Vessel Code

Controls and Safety Devices for

Automatically Fired Boilers

ASSE American Society of Safety Engineers

1800 East Oakton Street

Des Plaines, IL 60018

Standard Referenced

Title

ANSI/ASSE Z 359.1 -2007

Safety Requirements for Personal Fall Arrest Systems, Subsystems and Components, Part of the Fall Protection Code

ASSE American Society of Sanitary Engineering

901 Canterbury, Suite A

Westlake, OH 44145

Standard Referenced

Title

1017-2010

Performance Requirements for Temperature

Actuated Mixing Values for Hot Water

Distribution Systems

ASTMInternational

100 Barr Harbor Drive

West Conshohocken, PA 19428

Standard Referenced

Title

A 53/A 53M-12

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

A 106/A106M-14

Specification for Seamless Carbon Steel Pipe for High-Temperature Service

A 126-14

Specification for Gray Iron Castings for Valves, Flanges and Pipe Fittings

A 234/A234M-15

Standard Specification for Piping Fittings of Wrought Carbon Steel And Alloy Steel For

A 254/A254-12

Moderate and High Temperature Service Specification for Copper Brazed Steel Tubing

A 395/A395M-14

Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures

A 420/A 420M-16

Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service

A 536-14

Standard Specification for Ductile Iron Castings

A 539-99

Specification for Electric-resistance-welded Coiled Steel Tubing for Gas and Fuel Oil Lines

B 32-14

B 42-15

Specification for Solder Metal Specification for Seamless Copper Pipe, Standard Sizes

B 43-15

Specification for Seamless Red Brass Pipe, Standard Sizes

B 68-11

Specification for Seamless Copper Tube, Bright Annealed

B75-11

B 88-14

Specification for Seamless Copper Tube

Specification for Seamless Copper Water Tube

B 135-10

Specification for Seamless Brass Tube

B 251-10

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

B 280-16

Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service

B 302-12

Specification for Threadless Copper Pipe, Standard Sizes

B 813-16

Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube

C 315-07(2011)

Specification for Clay Flue Liners and Chimney Pots

C 411-11

Test Method for Hot-surface Performance of High-temperature Thermal Insulation

D 56-16

Test Method for Flash Point by Tag Closed Tester

D 93-16

Test Method for Flash Point of Pensky-Martens Closed Cup Tester

D 1527-99(2005)

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

D 1693-15

Test Method for Environmental Stress-Cracking of Ethylene Plastics

D 1785-15

Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe, Schedules 40, 80 and 120

D 2235-04(2011)

Specifications for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

D 2241-15

Specification for Poly (Vinyl Chloride)(PVC) Pressure-rated Pipe (SDR-Series)

D 2282-99(2005)

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)

D 2412-11

Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-plate Loading

D2464-15

Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2466-15

Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe Fittings, Schedule 40

D 2467-15

Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe Fittings, Schedule 80

D 2564-12

Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

D 2657-15

Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings.

D 2683-14

Specification for Socket-type Polyethylene Fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

D2737-12A

Standard Specification for Polyethylene (PE) Plastic Tubing

D 2846/D 2846M-14

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot and Cold Water Distribution Systems

D 2996-15

Specification for Filament-wound Fiberglass (Glass Fiber Reinforced Thermosetting Resin) Pipe

D 3035-2015

Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

D 3261-15

Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

D 3278-1996(2011)

Test Methods for Flash Point of Liquids by Small Scale Closed-cup Apparatus

D 3309-96a(2002)

Specification for Polybutylene (PB) Plastic Hot and Cold Water Distribution Systems

E 84-16

Test Method for Surface Burning Characteristics of Building Materials

E 119-2016a

Test Method for Fire Tests of Building Construction and Materials

E 136-16

Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 Degrees C

E 814-2013a

Test Method for Fire Tests of Through-penetration Fire Stops

E 1509-12

Specification for Room Heaters, Pellet Fuel-burning Type

E 2231-15

Standard Practice For Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface

E 2336-16

Burning Characteristics Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems

F437-15

Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 438-15

Specification for Socket Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

F 439-13

Specification for Socket Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 441/F 441M-15

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

F 442/F 442M-13

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)

F 493-14

Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

F 714-13

Standard Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) based on Outside Diameter

F 876-2015a

Specification for Cross-linked Polyethylene (PEX) Tubing

F 877-2011A

Specification for Cross-linked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems

F 1055-15

Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Cross-linked Polyethylene Pipe and Tubing

F 1281-11

Specification for Cross-linked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe

F 1282-10

Standard Specification for Polyethylene/Aluminum/ Polyethylene (PE-AL-PE) Composite Pressure Pipe

F 1476-07(2013)

Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications

F 1548-01(2012)

Standard Specification for the Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications

F 1807-15

Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR 9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polethylene of Raised Temperature (PE-RT) Tubing

F 1924-12

Standard Specification for Plastic Mechanical Fittings for Use on Outside

  

Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing

F1960-15

Specification for Cold-Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing

F 1974-09(2015)

Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure Pipe

F2080-15a

Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Cross-linked Polyethylene (PEX) Pipe

F2098-15

Standard Specification for Stainless Steel Clamps for SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal and Plastic Insert Fittings

F 2159-14

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR 9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

F 2389-15

Specification for Pressure-rated Polypropylene Piping Systems

F2434-14

Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/ Cross-linked Polyethylene (PEX-AL-PEX) Tubing

F 2623-14

Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 Tubing1

F 2735-09(2016)

Standard Specification for Plastic Insert Fittings for SDR 9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

F 2769-14

Polyethylene of Raised Temperature (PERT) Plastic Hot- and Cold-water Tubing and Distribution Systems

F 2806-15

Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR)

AWS American Welding Society

8669 NW 36 Street, #130

Doral, FL 33166

Standard Referenced

Title

A 5.8 M/A 5.8 -2011

Specifications for Filler Metals for Brazing and Braze Welding

AWWA American Water Work Association

6666 West Quincy Avenue

Denver, CO 80235

Standard Referenced

Title

C901-08

Polyethylene (PE) Pressure Pipe and Tubing, 1/ in. (13mm) through 3 in. (76mm) for Water Service

C110/A 21.10 -12

Standard for Ductile Iron & Gray Iron Fittings

C115/A 21.15 -11

Standard for Flanged Ductile-Iron Pipe with Ductile Iron or Grey-Iron Threaded Flanges

C151/A 21.51 -09

Standard for Ductile-Iron Pipe, Centrifugally Cast for Water

C153/A 21.53 -11

Standard for Ductile-Iron Compact Fittings for Water Service

CSA CSA Group

8501 East Pleasant Valley Road

Cleveland, OH 44131-5516

Standard Referenced

Title

B 137.2 -13

Polyvinylchloride (PVC) Injection-moulded Gasketed Fittings for Pressure Applications

B 137.3 -13

Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications

B 137.6 -13

Chlorinated Polyvinylchloride (CPVC) Pipe, Tubing and Fittings for Hot- and Cold-water Distribution Systems

B 137.9 -13

Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure-Pipe Systems

B 137.10 -13

Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Composite Pressure-Pipe Systems

CSA C448 Series-13

Design and Installation of Earth Energy Systems-First Edition; Update 2: October 2009; CAN/CSA 2002 Consolidated Reprint 10/2009

CSA B 137.1 -13

Polyethylene (PE) Pipe, Tubing and Fittings for Cold Water Pressure Services.

CSA B 137.5 -13

Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications

CSA B 137.11 -13

Polypropylene (PP-R) Pipe and Fittings for Pressure Applications

ANSI CSA

America FC1-2014

Stationary Fuel Cell Power Systems

DOL Department of Labor

Occupational Safety and Health Administration c/o Superintendent of Documents

US Government Printing Office

Washington, DC 20402-9325

Standard Referenced

Title

29 CFR Part 1910.1000 (2016)

Air Contaminants

29 CFR Part 1910.1025 (2016)

Toxic and Hazardous Substances

FS Federal Specifications*

General Services Administration 7th & D Streets

Specification Section, Room 6039 Washington, DC 20407

Standard Referenced

Title

WW-P-325B (1976)

Pipe, Bends, Traps, Caps and Plugs; Lead (for Industrial Pressure and Soil and Waste Applications) *Standards are available from the Supt. of Documents, U.S. Government Printing Office, Washington, DC 20402-9325

ICC International Code Council, Inc.

500 New Jersey Ave, NW

6th Floor

Washington, DC 20001

Standard Referenced

Title

IECC-12

IFGC-15

International Energy Conservation Code®

International Fuel Gas Code®

IIAR International Institute of Ammonia Refrigeration

1110 North Glebe Road

Arlington, VA 22201

Standard Referenced

Title

2-2014

Addendum A to Equipment, Design, and Installation of Ammonia Mechanical Refrigerating Systems

MSS Manufacturers Standardization Society of the Valve & Fittings Industry, Inc.

127 Park Street, N.E.

Vienna, VA 22180

Standard Referenced

Title

SP 58-2009

Pipe Hangers and Supports-Materials Design and Manufacture, Selection, Application and Installation

NAIMA North American Insulation Manufacturers Association

44 Canal Center Plaza, Suite 310

Alexandria, VA 22314

Standard Referenced

Title

AH116-09

Fibrous Glass Duct Construction Standards

NBBI National Board of Boiler and Pressure Vessel Inspectors

1055 Crupper Avenue

Columbus, OH 43229-1183

Standard Referenced

Title

NBIC- the edition referenced in rule 4101:4-3-01 of the Administrative Code

National Board Inspection Code, Part 3

NFPA National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

Standard Referenced

Title

30-15

30A-15

Flammable and Combustible Liquids Code

Code for Motor Fuel-dispensing Facilities and Repair Garages

31-16

Standard for the Installation of Oil-burning Equipment

37-15

Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines

58-17

Liquefied Petroleum Gas Code

69-14

Standard on Explosion Prevention Systems

70-17

National Electrical Code

72-16

National Fire Alarm and Signaling Code

75-09

Protection of Information Technology Equipment

82-14

Standard on Incinerators and Waste and Linen Handling Systems and Equipment

85-the edition referenced in rule 4101:4-3-01 of the Administrative Code

Boiler and Combustion Systems Hazards Code

91-15

Standard for Exhaust Systems for Air Conveying of Vapors, Gases, Mists, and Noncombustible Particulate Solids

92-15

Standard for Smoke Control Systems

96-14

Standard for Ventilation Control and Fire Protection of Commercial Cooking Operations

211-16

Standard for Chimneys, Fireplaces, Vents and Solid Fuel-burning Appliances

262-15

Standard Method of Test for Flame Travel and Smoke of Wires and Cables for Use in Air-handling Spaces

286-15

Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth 602.2.1.6.2

704-17

Standard System for Identification of the Hazards of Materials for Emergency Response

853-15

Standard on Installation of Stationary Fuel Power Plants

NSF NSF International

789 Dixboro Road, P. O. Box 130140

Ann Arbor, MI 48113-0140

Standard Referenced

Title

NSF 358-1-2014

Polyethylene Pipe and Fittings for Water Based Ground Source "Geothermal" Heat Pump Systems

SMACNA Sheet Metal & Air-Conditioning Contractors National Assoc., Inc.

4201 Lafayette Center Drive

Chantilly, VA 20151-1209

Standard Referenced

Title

SMACNA/ANSI-2015

HVAC Duct Construction Standards-Metal and Flexible 4th Edition (ANSI)

SMACNA-10

Fibrous Glass Duct Construction Standards

UL Underwriters Laboratories LLC

333 Pfingsten Road

Northbrook, IL 60062-2096

Standard Referenced

Title

17-2008

Vent or Chimney Connector Dampers for Oil-fired Appliances- with revisions Through January 2010 803.6

103-2010

Factory-built Chimneys, Residential Type and Building Heating Appliance- with revisions through July 2012

127-2011

Factory-built Fireplaces

174-04

Household Electric Storage Tank Water Heaters-with revisions through September 2012

180-2012

Liquid-level Indicating Gauges for Oil Burner Fuels and Other Combustible Liquids

181-13

Factory-made Air Ducts and Air Connectors

181A-2013

Closure Systems for Use with Rigid Air Ducts and Air Connectors

181B-2013

Closure Systems for Use with Flexible Air Ducts and Air Connectors

197-10

Commercial Electric Cooking Appliances- with revisions through June 2011

207-2009

Refrigerant-containing Components and Accessories, Nonelectrical

263-2011

Standard for Fire Test of Building Construction and Materials

268-2016

Smoke Detectors for Fire Alarm Systems

268A-2008

Smoke Detectors for Duct Application-with revisions through September 2009

343-2008

Pumps for Oil-Burning Appliances-with revisions through June 2013

378-06

Draft Equipment-with revisions through January 2010

391-2010

Solid-fuel and Combination-fuel Central and Supplementary Furnaces-with revisions through March 2010

412-2011

Refrigeration Unit Coolers-with revisions through August 2012

471-2010

Commercial Refrigerators and Freezers- with revisions through December 2012

499-14

Electric Heating Appliances

508-99

Industrial Control Equipment-with revisions through March 2013

536-14

Flexible Metallic Hose

555-06

Fire Dampers-with revisions through May 2012

555C-14

Ceiling Dampers

555S-14

Smoke Dampers

586-2009

High-Efficiency, Particulate, Air Filter Units

641-2010

Type L Low-temperature Venting Systems- with revisions through May 2013

705-2004

Standard for Power Ventilators-with revisions through March 2012

710-2012

Exhaust Hoods for Commercial Cooking Equipment

710B-2011

Recirculating Systems

723-2008

Standard for Test for Surface Burning Characteristics of Building Materials

726-95

Oil-fired Boiler Assemblies-with revisions through April 2011

727-06

Oil-fired Central Furnace-with revisions through April 2010

729-03

Oil-fired Floor Furnaces-with revisions through August 2012

730-03

Oil-fired Wall Furnaces-with revisions through August 2012

731-95

Oil-fired Unit Heaters-with revisions through August 2012

732-95

Oil-fired Storage Tank Water Heaters-with revisions through April 2010

737-2011

Fireplace Stoves

762-2013

Outline of Investigation for Power Ventilators for Restaurant Exhaust Appliances

791-06

Residential Incinerators-with revisions through April 2010

834-04

Heating, Water Supply and Power Boilers Electric-with revisions through January 2013

842-15

Valves for Flammable Fluids

858-14

Household Electric Ranges

867-2011

Electrostatic Air Cleaners-with revisions through February 2013

875-09

Electric Dry Bath Heater-with revisions through November 2011

896-93

Oil-burning Stoves-with revisions through August 2012

900-15

Air Filter Units

907-16

Fireplace Accessories

923-2013

Microwave Cooking Appliances

959-2010

Medium Heat Appliance Factory-built Chimneys

1046-2010

Grease Filters for Exhaust Ducts-with revisions through January 2012

1240-2012

Electric Commercial Clothes-Drying Equipment-with revisions through October 2012

1261-01

Electric Water Heaters for Pools and Tubs- with revisions through July 2012

1453-16

Electric Booster and Commercial Storage Tank Water Heaters

1479-15

Fire Tests of Through-penetration Firestops

1482-2011

Solid-fuel Type Room Heaters

1618-15

Wall Protectors, Floor Protectors and Hearth Extensions

1777-2015

Chimney Liners

1812-2013

Standard for Ducted Heat Recovery Ventilators

1815-2012

Standard for Nonducted Heat Recovery

1820-04

Fire Test of Pneumatic Tubing for Flame and Smoke Characteristics-with revisions through May 2013

1887-04

Fire Tests of Plastic Sprinkler Pipe for Visible Flame and Smoke Characteristics- with revisions through May 2013

1978-2010

Grease Ducts

1995-2015

Heating and Cooling Equipment

1996-2009

Electric Duct Heaters-with revisions through November 2011

2024-2014

Standard for Safety Optical-Fiber and Communications Cable Raceway- with revisions through April 2011

2043-2013

Fire Test for Heat and Visible Smoke Release for Discrete Products and their Accessories Installed in Air-handling Spaces

2085-10

Protected Above-Ground Tanks for Flammable and Combustible Liquids

2158-15

Electric Clothes Dryers

2158A-2013

Outline of Investigation for Clothes Dryer Transition Duct

2162-14

Outline of Investigation for Commercial Wood-fired Baking Ovens-Refractory Type

2200-2012

Stationery Engine Generator Assemblies- with revisions through June 2013

2221-2010

Tests of Fire Resistive Grease Duct Enclosure Assemblies

2518-16

Air Dispersion System Materials

2523-09

Solid Fuel-fired Hydronic Heating Appliances-with revisions through February 2013

Replaces: 4101:2-15-01

Cite as Ohio Admin. Code 4101:2-15-01

Effective: 11/1/2017
Five Year Review (FYR) Dates: 11/01/2022
Promulgated Under: 119.03
Statutory Authority: 3781.10(A)
Rule Amplifies: 3781.10 , 3781.11, 3791.04
Prior Effective Dates: 7/1/82, 3/1/85, 3/1/86, 1/1/89, 9/1/92, 7/1/95, 2/1/96, 3/1/98, 7/1/98, 1/1/02, 1/1/04, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08, 1/1/09, 11/1/11, 3/1/13, 1/1/15, 1/1/16

4101:2-15-01.1 General. [Rescinded].

Rescinded eff 7-1-07

Cite as Ohio Admin. Code 4101:2-15-01.1

4101:2-15-01.2 Referenced codes. [Rescinded].

Rescinded eff 7-1-07

Cite as Ohio Admin. Code 4101:2-15-01.2

4101:2-15-01.3 Referenced standards. [Rescinded].

Rescinded eff 7-1-07

Cite as Ohio Admin. Code 4101:2-15-01.3