Referenced code

Ohio Administrative Code chapters

Building Code

4101:1-1 to 4101:1-35

Fire Code

1301:7-1 to 1301:7-7

Mechanical Code

4101:2-1 to 4101:2-15

Ohio Boiler and Pressure Vessel Rules

4101:4-1 to 4101:4-10

Standard Referenced

Title

A118.10-10

Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin Set Ceramic Tile and Dimension Stone Installation

Z4.3-95 (R2005)

Minimum Requirements for Nonsewered Waste-Disposal Systems (Standard is developed by the Portable SanitationAssociation International-PSAI)

Z21.22-99 (R2003)

Relief Valves for Hot Water Supply Systems with Addenda Z21.22a-2000 (R2003) and Z21.22b-2001 (R2003) (Standardis developed by the Canadian Standards Association-CSA andis the same as CSA 4.4-M99)

Z124.1.2-05

Plastic Bathtub and Shower Units (Standard is developed byIAPMO)

Z124.3-05

Plastic Lavatories (Standard is developed by IAPMO)

Z124.4-06

Plastic Water Closet Bowls and Tanks (Standard is developedby IAPMO)

Z124.6-07

Plastic Sinks (Standard is developed by IAPMO)

Z124.9-04

Plastic Urinal Fixtures. (Standard is developed by IAPMO)

Standard Referenced

Title

1010-02 Coolers

Self-contained, Mechanically Refrigerated Drinking-Water

Standard Referenced

Title

A112.1.2-2004

Air Gaps in Plumbing Systems

A112.1.3-2000 (R 2005)

Air Gap Fittings for Use with Plumbing Fixtures, Appliances and Appurtenances

A112.3.1-2007

Stainless Steel Drainage Systems for Sanitary, DWV, Storm and Vacuum Applications Above and Below Ground

A112.3.4-2000 (R 2004)

Macerating Toilet Systems and Related Components

A112.4.1-2009

Water Heater Relief Valve Drain Tubes

A112.4.3-1999 (R 2004)

Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System

A112.6.1M-1997 (R2002)

Floor-affixed Supports for Off-the-floor Plumbing Fixtures for Public Use

A112.6.2-2000 (R2004)

Framing-affixed Supports for Off-the-floor Water Closets with Concealed Tanks

A112.6.3-2001 (R 2007)

2001 Floor and Trench Drains

A112.6.7-2001 (R 2007)

Enameled and Epoxy-coated Cast-iron and PVC Plastic Sanitary Floor Sinks

A112.14.1-2003

Backwater Valves

A112.14.3-2000

Grease Interceptors

A112.14.4-2001(R2007)

Grease Removal Devices

A112.18.1-2005

Plumbing Supply Fittings

CSA B125.1-2005/A112.18.2-2005

Plumbing Waste Fittings

CSA B125.2-2005/A112.18.3-2002

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

A112.18.6-2009

Flexible Water Connectors.

A112.18.7-1999 (R2004)

Deck mounted Bath/Shower Transfer Valves with Integral Backflow Protection

A112.19.1M-2008

Enameled Cast Iron Plumbing Fixtures

A112.19.2-2008

Vitreous China Plumbing Fixtures and Hydraulic Requirements for Water Closets and Urinals .

A112.19.3M-2008

Stainless Steel Plumbing Fixtures (Designed for Residential Use

A112.19.4M-1994 (R 2004)

Porcelain Enameled Formed Steel Plumbing Fixtures.

A112.19.5-2005

Trim for Water-closet Bowls, Tanks and Urinals

A112.19.6-1995

Hydraulic Performance Requirements for Water Closets and Urinals

A112.19.7M-2006

HydromassageBathtub Appliances

A112.19.8M-2007

Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, Hot Tubs

A112.19.9M-1991(R2002)

Nonvitreous Ceramic Plumbing Fixtures with 2002 Supplement

A112.19.12-2006

Wall Mounted and Pedestal Mounted, Adjustable, Elevating, Tilting and Pivoting Lavatory, Sink and Shampoo Bowl Carrier Systems and Drain Systems

A112.19.13-2001 (R2007)

ElectrohydraulicWater Closets

A112.19.15- 2005

Bathtub/Whirlpool Bathtubs with Pressure Sealed Doors

A112.19.19-2006

Vitreous ChinaNonwaterUrinals

A112.21.2M-1983

Roof Drains

A112.36.2M-1991(R2002)

Cleanouts

B1.20.1-1983(R2006)

Pipe Threads, General Purpose (inch

B16.3-2006

Malleable Iron Threaded Fittings Classes 150 and 300

B16.4-2006

Gray Iron Threaded Fittings Classes 125 and 250

B16.9-2007

Factory-made Wrought Steel Buttwelding Fittings.

B16.11-2009

Forged Fittings, Socket-welding and Threaded.

B16.12-2009

Cast-iron Threaded Drainage Fittings

B16.15-2006

Cast Bronze Threaded Fittings

B16.18-2001(R 2005)

Cast Copper Alloy Solder Joint Pressure Fittings

B16.22-2001 (R2005)

Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

B16.23-2002 (R 2006)

Cast Copper Alloy Solder Joint Drainage Fittings DWV

B16.26-2006

Cast Copper Alloy Fittings for Flared Copper Tubes .

B16.28-1994

Wrought Steel Buttwelding Short Radius Elbows and Returns

B16.29-2007

Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings (DWV)

BPVC Section IX- 2010

Welding and Brazing Qualifications.

Standard Referenced

Title

1001-08

Performance Requirements for Atmospheric Type Vacuum Breakers

1002-08

Performance Requirements for Antisiphon Fill Valves (Ballcocks) for Gravity Water Closet Flush Tanks

1003-09

Performance Requirements for Water Pressure Reducing Valves .

1004-08

Performance Requirements for Backflow Prevention Requirements for Commercial Dishwashing Machines .

1005-99

Performance Requirements for Water Heater Drain Valves.

1006-86

Performance Requirements for Residential Use Dishwashers.

1007-86

Performance Requirements for Home Laundry Equipment

1008-06

Performance Requirements for Household Food Waste Disposer Units

1009-90

Performance Requirements for Commercial Food Waste Grinder Units

1010-04

Performance Requirements for Water Hammer Arresters

1011-04

Performance Requirements for Hose Connection Vacuum Breakers

1012-09

Performance Requirements for Backflow Preventers with Intermediate Atmospheric Vent .

1013-09

Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Fire Protection Principle Backflow Preventers

1015-09

Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

1016-05

Performance Requirements for Individual Thermostatic, Pressure Balancing and Combination Control Valves for Individual Fixture Fittings

1017-09

Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems.

1018-01

Performance Requirements for Trap Seal Primer Valves; Potable Water Supplied

1019-04

Performance Requirements for Vacuum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining Type

1020-04

Performance Requirements for Pressure Vacuum Breaker Assembly

1022-03

Performance Requirements for Backflow Preventer for Beverage Dispensing Equipment

1024-04

Performance Requirements for Dual Check Valve Type Backflow Preventers (for Residential Supply Service or Individual Outlets

1035-08

Performance Requirements for Laboratory Faucet Backflow Preventers

1037-90

Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

1044-01

Performance Requirements for Trap Seal Primer Devices Drainage Types and Electronic Design Types

1047-09

Performance Requirements for Reduced Pressure Detector Fire Protection BackflowPrevention Assemblies

1048-09

Performance Requirements for Double Check Detector Fire Protection BackflowPrevention Assemblies

1050-09

Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems .

1051-09

Performance Requirements for Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems-fixture and Branch Devices

1052-04

Performance Requirements for Hose Connection Backflow Preventers

1055-09

Performance Requirements for Chemical Dispensing Systems

1056-01

Performance Requirements for Spill Resistant Vacuum Breaker

1060-06

Performance Requirements for Outdoor Enclosures for Backflow Prevention Assemblies

1061-06

Performance Requirements for Removable and Nonremovable Push Fit Fittings

1062-06

Performance Requirements for Temperature Actuated, Flow Reduction Valves to Individual Fixture Fittings

1066-97

Performance Requirements for Individual Pressure Balancing In-line Valves for Individual Fixture Fittings

1069-05

Performance Requirements for Automatic Temperature Control Mixing Valves

1070-04

Performance Requirements for Water-temperature Limiting Devices

1072-07

Performance Requirements for Barrier Type Floor Drain Trap Seal Protection Devices

1079-05

Dielectric Pipe Unions.

5013-09

Performance Requirements for Testing Reduced Pressure Principle Backflow Prevention Assembly (RPA) and Reduced Pressure Fire Protection PrincipleBackflow Preventers(RFP)

5015-09

Performance Requirements for Testing Double Check Valve Backflow Prevention Assembly (DCVA)

5020-09

Performance Requirements for Testing Pressure Vacuum Breaker Assembly (PVBA)

5047-09

Performance Requirements for Testing Reduced Pressure Detector Fire Protection BackflowPrevention Assemblies (RPDA) .

5048-09

Performance Requirements for Testing Double Check Valve Detector Assembly (DCDA).

5052-09

Performance Requirements for Testing Hose Connection Backflow Preventers

5056-09

Performance Requirements for Testing Spill Resistant Vacuum Breaker.

Standard Referenced

Title

A 53/A 53M-10

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

A 74-09

Specification for Cast-iron Soil Pipe and Fittings

A 312/A 312M-09

Specification for Seamless and Welded Austenitic Stainless Steel Pipes

A 733-03 (2009)e1

Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples

A 778-01(2009)e1

Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products

A 888-09

Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Application

B 32-08

Specification for Solder Metal

B 42-10

Specification for Seamless Copper Pipe, Standard Sizes

B 43-09

Specification for Seamless Red Brass Pipe, Standard Sizes

B 75-02

Specification for Seamless Copper Tube

B 88-09

Specification for Seamless Copper Water Tube

B 152/B 152M-09

Specification for Copper Sheet, Strip Plate and Rolled Bar

B 251-10

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

B 302-07

Specification for Threadless Copper Pipe, Standard Sizes

B 306-09

Specification for Copper Drainage Tube (DWV)

B 447-07

Specification for Welded Copper Tube

B 687-99(2005)e01

Specification for Brass, Copper and Chromium-plated Pipe Nipples

B 813-10

Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube

B 828-02

Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings.

C 4-04 (2009)

Specification for Clay Drain Tile and Perforated Clay Drain Tile

C 14-07

Specification for Nonreinforced Concrete Sewer, Storm Drain and Culvert Pipe.

C 76-10a

Specification for Reinforced Concrete Culvert, Storm Drain and Sewer Pipe

C 296-00 (2009)e1

Specification for Asbestos-cement Pressure Pipe

C 425-04 (2009)

Specification for Compression Joints for Vitrified Clay Pipe and Fittings

C 428-05 (2006)

Specification for Asbestos-cement Nonpressure Sewer Pipe

C 443-05ae1

Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

C 508- 00 (2009)e1

Specification for Asbestos-cement Underdrain Pipe

C 564-09a

Specification for Rubber Gaskets for Cast-iron Soil Pipe and Fittings

C 700-09

Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated .

C 1053-00(2010)

Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications

C 1173-08

Specification for Flexible Transition Couplings for Underground Piping System.

C 1277-09a

Specification for Shielded Coupling Joining Hubless Cast-iron Soil Pipe and Fittings

C 1440-08

Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste,and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems

C 1460-08

Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground

C 1461-08

Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste and Vent (DWV) Sewer, Sanitary and Storm Plumbing Systems for Above and Below Ground Use

C 1540-09a

Specification for Heavy Duty Shielded Couplings Joining Hubless Cast-iron Soil Pipe and Fittings

C 1563-08

Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent and Storm Piping Applications

D 1527-99(2005)

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

D 1785-06

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

D 1869-95(2005)e1

Specification for Rubber Rings for Asbestos-cement Pipe

D 2235-04

Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

D 2239-03

Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

D 2241-09

Specification for Poly (Vinyl Chloride) (PVC) Pressure-rated Pipe (SDR-Series)

D 2282-(2005)99e01

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)

D 2464-06

Specification for Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2466-06

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40

D 2467-06

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2468-96a

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40

D 2564-04 (2009) e01

Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

D 2609-02 (2008)

Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe.

D 2657-07

Practice for Heat Fusion-joining of Polyolefin Pipe and Fitting

D 2661-08

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

D 2665-09

Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

D 2672-96a(2009)

Specification for Joints for IPS PVC Pipe Using Solvent Cement .

D 2683-10

Standard Specification for Socket-type Polyethylene fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

D 2729-03

Specification for Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

D 2737-03

Specification for Polyethylene (PE) Plastic Tubing

D 2751-05

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings

D 2846/D 2846M-09b

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot and Cold Water Distribution Systems

D 2855-96(2010)

Standard Practice for Making Solvent-cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings D 2949-01ae01 Specification for 3.25-in Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

D 3034-08

Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

D 3035-08

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

D 3139-98(2005)

Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

D 3212-07

Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

D 3261-10a

Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic fittings for Polyethylene (PE) Plastic Pipe and Tubing

D 3311-06a09a

Specification for Drain, Waste and Vent (DWV) Plastic Fittings Patterns

D 4068-09

Specification for Chlorinated Polyethlene (CPE) Sheeting for Concealed Water-containment Membrane

D 4551-96(2008) e1

Specification for Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-containment Membrane

F 405-05

Specification for Corrugated Polyethylene (PE) Tubing and Fittings

F 409-02(2008)

Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings .

F 437-09

Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 438-09

Specification for Socket-type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

F 439-09

Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 441/F 441M-09

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

F 442/F 442M-09

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)

F 477-10

Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

F 493-10

Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

F 628-08

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core

F 656-10

Specification for Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

F 714-08

Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter

F 876-10

Specification for Cross-linked Polyethylene (PEX) Tubing

F 877-07

Specification for Cross-linked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems

F 891-10

Specification for Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core .

F 1055-98(2006)

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing

F 1281-07

Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Pressure Pipe

F 1282-10

Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

F 1412-09

Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage

F 1488-09

Specification for Coextruded Composite Pipe

F 1673-10

PolyvinylideneFluoride (PVDF) Corrosive Waste Drainage Systems

F 1807-07

Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing

F 1866-07

Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings .

F 1960-10

Specification for Cold Expansion Fittings with PEX Reinforcing Rings for use with Cross-linked Polyethylene (PEX) Tubing.

F 1974-09

Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure Pipe

F 1986-01(2006)

Specification for Multilayer Pipe, Type 2, Compression Fittings and Compression Joints for Hot and Cold Drinking Water Systems.

F 2080-09

Specifications for Cold-expansion Fittings with Metal Compression-sleeves for Cross-linked Polyethylene (PEX) Pipe

F 2098-08

Standard specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert Fittings

F 2159-10

Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing

F 2262-09

Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Tubing OD Controlled SDR9

F 2306/F 2306M-08

12" to 60" Annular Corrugated Profile-wall Polyethylene (PE) Pipe and Fittings for Gravity Flow Storm Sewer and Subsurface Drainage Applications

F 2389-10

Specification for Pressure-rated Polypropylene (PP) Piping Systems

F 2434-09

Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEXAL-PEX) Tubing.

Standard Referenced

Title

A5.8-04

Specifications for Filler Metals for Brazing and Braze Welding

Standard Referenced

Title

C104/A21.4-08

Standard for Cement-mortar Lining for Ductile-iron Pipe and Fittings for Water

C110/A21.10-08

Standard for Ductile-iron and Gray-iron Fittings, 3 Inches through 48 Inches, for Water

C111/A21.11-06

Standard for Rubber-gasket Joints for Ductile-iron Pressure Pipe and Fittings

C115/A21.15-05

Standard for Flanged Ductile-iron Pipe with Ductile-iron or Gray-iron Threaded Flanges

C151/A21.51-09

Standard for Ductile-iron Pipe, Centrifugally Cast for Water

C153/A21.53-06

Standard for Ductile-iron Compact Fittings for Water Service

C510-07

Double Check Valve Backflow Prevention Assembly

C511-07

Reduced-pressure Principle Backflow Prevention Assembly

C651-05

Disinfecting Water Mains

C652-02

Disinfection of Water-storage Facilities

Standard Referenced

Title

301-09

Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

310-09

Specification for Coupling for Use in Connection with Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

Standard Referenced

Title

B45.1-02 (R2008)

Ceramic Plumbing Fixtures.

B45.2-02 (R2008)

Enameled Cast-iron Plumbing Fixtures

B45.3-02 (R2008)

Porcelain Enameled Steel Plumbing Fixtures

B45.4-02 (R2008)

Stainless-steel Plumbing Fixtures

B45.5-02 (R2008)

Plastic Plumbing Fixtures

B45.9-99 (R2008)

Macerating Systems and Related Components

B64.1.2-07

Vacuum Breakers, Pressure Type (PVB

B64.2.1-07

Vacuum Breakers, Hose Connection Type (HCVB) with Manual Draining Feature

B64.2.1.1-07

Vacuum Breakers, Hose Connection Dual Check Type (HCDVB)

B64.4.1-07

Backflow Preventers, Reduced Pressure Principle Type for Fire Sprinklers (RPF)

B64.5-07

Backflow Preventers, Double Check Type (DCVA)

B64.5.1-07

Backflow Preventers, Double Check Type for Fire Systems (DCVAF)

B64.6-07

Backflow Preventers, Dual Check Valve Type (DuC)

B64.7-07

Vacuum Breakers, Laboratory Faucet Type (LFVB

B64.10/B64.10.1-07

Manual for the Selection and Installation of Backflow Prevention Devices/Manual for the Maintenance and Field Testing of Backflow Prevention Devices

B79-08

Floor, Area and Shower Drains, and Cleanouts for Residential Construction

B125-01

Plumbing Fittings

B125.3-2005

Plumbing Fittings

B137.1-09

Polyethylene Pipe, Tubing and Fittings for Cold Water Pressure Services

B137.2-09

PVC Injection-moulded Gasketed Fittings for Pressure Applications

B137.3-09

Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications

B137.5-09

Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications-with Revisions through September 1992

B137.6-09

CPVC Pipe, Tubing and Fittings for Hot and Cold Water Distribution Systems- with Revisions through May 1986B137.11-02 Polypropylene (PP-R) Pipe and Fittings for Pressure Applications

B181.1-06

ABS Drain, Waste and Vent Pipe and Pipe Fittings

B181.2-06

PVC Drain, Waste, and Vent Pipe and Pipe Fittings- with Revisions through December 1993

B182.1-06

Plastic Drain and Sewer Pipe and Pipe Fittings

B182.2-06

PVC Sewer Pipe and Fittings (PSM Type)

B182.4-06

Profile PVC Sewer Pipe and Fittings

B182.6-06

Profile Polyethylene Sewer Pipe and Fittings for Leak-proof Sewer Applications

B182.8-06

Profile Polyethylene Storm Sewer and Drainage Pipe and Fittings

CAN/CSA-A257.1M-09

Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

CAN/CSA-A257.2M-09

Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

CAN/CSA-A257.3M-09

Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections and Fittings Using Rubber Gaskets

CAN/CSA-B64.1.1-07

Vacuum Breakers, Atmospheric Type (AVB)

CAN/CSA-B64.2-07

Vacuum Breakers, Hose Connection Type (HCVB).

CAN/CSA-B64.2.2-07

Vacuum Breakers, Hose Connection Type (HCVB) with Automatic Draining Feature

CAN/CSA-B64.3-07

Backflow Preventers, Dual Check Valve Type with Atmospheric Port (DCAP)

CAN/CSA-B64.4-07

Backflow Preventers, Reduced Pressure Principle Type (RP)

CAN/CSA-B64.10-07

Manual for the Selection, Installation, Maintenance and Field Testing of Backflow Prevention Devices

CAN/CSA-B137.9-09

Polyethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems

CAN/CSA-B137.10M-09

Cross-linked Polyethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems

CAN/CSA-B181.3-06

Polyolefin Laboratory Drainage Systems

CAN/CSA-B182.4-06

Profile PVC Sewer Pipe and Fittings

CAN/CSA-B602-10

Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe

Standard Referenced

Title

IFGC-09

International Fuel Gas Code (including ICC Emergency Amendment changing IFGC Sections 406.7 )

Standard Referenced

Title

Z358.1-09

Emergency Eyewash and Shower Equipment

Standard Referenced

Title

70-11

National Electrical Code

99C-05

Gas and Vacuum Systems

Standard Referenced

Title

3-2009

Commercial Warewashing Equipment

14-2010

Plastic Piping System Components and Related Materials

18-2009

Manual Food and Beverage Dispensing Equipment

42-2009

Drinking Water Treatment Units-Aesthetic Effects

44-2009

Residential Cation Exchange Water Softeners

53-2009e

Drinking Water Treatment Units-Health Effects.

58-2009

Reverse Osmosis Drinking Water Treatment Systems

61-2010a

Drinking Water System Components-Health Effects

62-2009

Drinking Water Distillation Systems

Standard Referenced

Title

G101(2010)

Testing and Rating Procedure for Grease Interceptors with Appendix of Sizing and Installation Data

Standard Referenced

Title

UL 508-99

Industrial Control Equipment with Revision through July 2005