Chapter 4101:3-15 Codes and Standards

4101:3-15-01 Referenced standards.

1501.1 General. This chapter lists the codes and standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date, and the title. The application of the referenced standards shall be as specified in Section 102.5 of the building code.

1501.2 Referenced codes. When indicated in the "OPC", the following codes refer to provisions in the listed chapters of the Administrative Code:

Referenced code

Ohio Administrative Code chapters

Building Code

4101:1-1 to 4101:1-35

Fire Code

1301:7-1 to 1301:7-7

Mechanical Code

4101:2-1 to 4101:2-15

Ohio Boiler and Pressure Vessel Rules

4101:4-1 to 4101:4-10

1501.3 Referenced Standards.

ANSI American National Standards Institute

25 West 43rd Street, Fourth Floor

New York, NY 10036

Standard Referenced

Title

A 118.10 -14

Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin Set Ceramic Tile and Dimension Stone Installation

Z 4.3 -95 (R2005)

Minimum Requirements for Nonsewered Waste-disposal Systems

(Standard is developed by the Portable Sanitation Association International-PSAI)

Z 21.22 -15

Relief Valves for Hot Water Supply Systems with Addenda

(Standard is developed by the Canadian Standards Association-CSA and is the same as CSA 4.4 )

AHRI Air-Conditioning, Heating,& Refrigeration Institute

4100 North Fairfax Drive. Suite 200

Arlington. VA 22203

Standard Referenced

Title

1010-02

Self-contained, Mechanically Refrigerated Drinking-Water Coolers

API American Petroleum Institute

1220 L Street NW Washington, DC 20005-4070

Standard Referenced

Title

12D-2008

Specification for Field Welded Tanks for Storage of Production Liquids, effective April 1, 2009

12F-2008

Specification for Shop Welded Tanks for Storage of Production Liquids, effective April 1 2009

ASME American Society of Mechanical Engineers

Three Park Avenue

New York, NY 10016-5990

Standard Referenced

Title

A112.1.2-2012

Air Gaps in Plumbing Systems

A112.1.3-2000 (R2015)

Air Gap Fittings for Use with Plumbing Fixtures, Appliances and Appurtenances

A112.3.1-2007 (2014)

Stainless Steel Drainage Systems for

Sanitary, DWV, Storm and

Vacuum Applications Above and Below

Ground

ASME Al 12.3.4-2013/

Macerating Toilet Systems and Related

CSAB 45.9 -2013

Components

A112.4.1-2009 (R2014)

Water Heater Relief Valve Drain Tubes

Al 12.4.2-2075

Water Closet Personal Hygiene Devices

A112.4.3-1999 (R2015)

Plastic Fittings for Connecting Water Closets

  

to the Sanitary Drainage System

A112.4.14-2004 (R2010)

Manually Operated, Quarter-Turn Shutoff

  

Valves for Use in Plumbing Systems

A112.6.1M-1997 (R2012)

Floor-affixed Supports for Off-the-floor

  

Plumbing Fixtures for Public Use

A112.6.2-2000 (R2010)

Framing-affixed Supports for Off-the-floor

  

Water Closets with Concealed Tanks

A112.6.3-2016

Floor and Trench Drains

A112.6.4-2003 (R2012)

Roof, Deck, and Balcony Drains

A112.6.7-2010 (R2015)

Enameled and Epoxy-coated Cast-iron and

  

PVC Plastic Sanitary Floor Sinks

A112.6.9-2005 (R2015)

Siphonic Roof Drains

A112.14.1-2003 (R2012)

Backwater Valves

A112.14.3-2000 (R2014)

Grease Interceptors

A112.14.4-2001 (R2012)

Grease Removal Devices

A112.14.6-2010 (R2015)

FOG (Fats, Oils and Greases) Disposal

  

Systems

A112.18.1-2012/

Plumbing Supply Fittings

CSA B 125.1 -2012

  

A112.18.2-2015/

Plumbing Waste Fittings

CSA B 125.2 -2015

  

A112.18.3-2002 (R2012)

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

A112.18.6/

Flexible Water Connectors

CSA B 125.6 -2009 (R2014)

  

A112.18.7-1999 (R2004)

Deck mounted Bath/Shower Transfer Valves

  

with Integral Backflow Protection

A112.18.9-2011

Protectors/Insulators for Exposed Waste and

  

Supplies on Accessible Fixtures

A112.19.1/-2013

Enameled Cast Iron and Enameled Steel

CSA B 45.2 -2013

Plumbing Fixtures

A112.19.2-2013/

Ceramic Plumbing Fixtures

CSA B 45.1 -13

  

A112.19.3-2008/

Stainless Steel Plumbing Fixtures

CSA B 45.4 -08(R2013)

  

A112.19.5/-2011

Flush Valves and Spuds for Water-closets,

CSA B 45.15 -2011

Urinals, and Tanks

A112.19.7M-2012/

Hydromassage Bathtub Systems

CSA B 45.10 -2012

  

A112.19.12-2014

Wall Mounted and Pedestal Mounted, Adjustable, Elevating, Tilting and Pivoting Lavatory, Sink and Shampoo Bowl

Carrier Systems and Drain Systems

A112.19.14-2013

Six-Liter Water Closets Equipped with a Dual Flushing Device

A112.19.15-2012

Bathtub/Whirlpool Bathtubs with Pressure Sealed Doors

A112.19.19-2006

Vitreous China Nonwater Urinals

A112.21.3-1985(R2007)

Hydrants for Utility and Maintenance Use

A112.36.2M-1991(R2012)

Cleanouts

ASSE 1016/ ASME

Performance Requirements for Individual

A 112.1016 /

Thermostatic, Pressure Balancing and

CSA B 125.16 -2011

Combination Control Valves for Individual Fixture Fittings

B1.20.1-2013

Pipe Threads, General Purpose (inch)

B 16.3 -2011

Malleable Iron Threaded Fittings Classes 150 and 300

B 16.4 -2011

Gray Iron Threaded Fittings Classes 125 and 250

B 16.9 -2012

Factory-made Wrought Steel Buttwelding Fittings

B 16.11 -2011

Forged Fittings, Socket-welding and Threaded

B 16.12 -2009 (R2014)

Cast-iron Threaded Drainage Fittings

B 16.15 -2013

Cast Bronze Threaded Fittings

B 16.18 -2012

Cast Copper Alloy Solder Joint Pressure Fittings

B 16.22 -2013

Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

B 16.23 -2011

Cast Copper Alloy Solder Joint Drainage Fittings DWV

B 16.26 -2013

Cast Copper Alloy Fittings for Flared Copper Tubes

B 16.28 -1994

Wrought Steel Buttwelding Short Radius Elbows and Returns

B 16.29 -2012

Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings (DWV)

B 16.34 -2013

Valves Flanged, Threaded and Welding End

B 16.51 -2013

Copper and Copper Alloy Press-Connect

Pressure Fittings

BPVC Section IX-the edition referenced in rule 4101:4-3-01 of the Administrative Code

Welding and Brazing Qualifications

ASPE American Society of Plumbing Engineers

8614 Catalpa Avenue, Suite 1007

Chicago, IL 60656-1116

Standard Referenced

Title

45-2013

Siphonic Roof Drainage Systems

ASSE American Society of Sanitary Engineering

901 Canterbury Road, Suite A

Westlake, OH 44145

Standard Referenced

Title

1001-2008

Performance Requirements for Atmospheric Type Vacuum Breakers

1002-2015

Performance Requirements for Antisiphon Fill Valves (Ballcocks) for

Gravity Water Closet Flush Tanks

1003-2009

Performance Requirements for Water Pressure Reducing Valves

1004-2008

Performance Requirements for Backflow Prevention Requirements for Commercial Dishwashing Machines

1005-1999

Performance Requirements for Water Heater Drain Valves

1008-2006

Performance Requirements for Plumbing Aspects of Food Waste Disposer Units

1010-2004

Performance Requirements for Water Hammer Arresters

1011-2004

Performance Requirements for Hose Connection Vacuum Breakers

1012-2009

Performance Requirements for Backflow Preventers with Intermediate

  

Atmospheric Vent

1013-2011

Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Principle Fire Protection Backflow Preventers

1015-2011

Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

ASSE 1016/ ASME

Performance Requirements for Individual

A 112.1016 /

Thermostatic, Pressure Balancing and

CSA B 125.16 -2011

Combination Control Valves for Individual Fixture Fittings

1017-2010

Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems

1018-2010

Performance Requirements for Trap Seal Primer Valves; Potable Water Supplied

1019-2011

Performance Requirements for Vacuum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining Type

1020-2004

Performance Requirements for Pressure Vacuum Breaker Assembly

1022-2003

Performance Requirements for Backflow Preventer for Beverage Dispensing Equipment

1024-2004

Performance Requirements for Dual Check Valve Type Backflow Preventers (for Residential Supply Service or Individual Outlets)

1035-2008

Performance Requirements for Laboratory Faucet Backflow Preventers

1037-2015

Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

1044-2015

Performance Requirements for Trap Seal Primer Devices Drainage Types and Electronic Design Types

1047-2011

Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies

1048-2011

Performance Requirements for Double

  

Check Detector Fire Protection Backflow Prevention Assemblies

1049-2009

Performance Requirements for Individual and Branch Type Air Admittance Valves for Chemical Waste Systems

1050-2009

Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems

1051-2009

Performance Requirements for Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems-fixture and Branch Devices

1052-2016

Performance Requirements for Hose Connection Backflow Preventers

1055-2009

Performance Requirements for Chemical Dispensing Systems

1056-2013

Performance Requirements for Spill Resistant Vacuum Breaker

1060-2006

Performance Requirements for Outdoor Enclosures for Fluid Conveying Components

1061-2015

Performance Requirements for Removable and Nonremovable Push Fit Fittings

1062-2006

Performance Requirements for Temperature Actuated, Flow Reduction Valves to Individual Supply Fittings

1066-2009

Performance Requirements for Individual Pressure Balancing In-line Valves for Individual Fixture Fittings

1069-2005

Performance Requirements for Automatic Temperature Control Mixing Valves

1070-2015

Performance Requirements for Water-temperature Limiting Devices

1072-2007

Performance Requirements for Barrier Type Floor Drain Tap Seal Protection Devices

1079-2012

Performance Requirements for Dielectric Pipe Unions

5013-2015

Performance Requirements for Testing Reduced Pressure Principle Backflow Prevention Assembly (RPA) and Reduced Pressure Fire Protection Backflow Preventers (RFP)

5015-2015

Performance Requirements for Testing Double Check Valve Backflow Prevention Assemblies (DC) and Double Check Fire Protection Backflow Prevention Assemblies (DCF)

5020-2015

Performance Requirements for Testing Pressure Vacuum Breaker Assemblies (PVBA)

5047-2015

Performance Requirements for Testing Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies (RPDA)

5048-2015

Performance Requirements for Testing Double Check Valve Detector Assembly (DCDA)

5052-2015

Performance Requirements for Testing Hose Connection Backflow Preventers

5056-2015

Performance Requirements for Testing Spill Resistant Vacuum Breaker (SRVB)

ASTM ASTM International

100 Barr Harbor Drive

West Conshohocken, PA 19428-2959

Standard Referenced

Title

A 53/A 53M-12

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

A 74-16

Specification for Cast-iron Soil Pipe and Fittings

A 312/A 312M-16

Specification for Seamless, Welded, And Heavily Cold Worked Austenitic Stainless Steel Pipes

A 733-15

Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples

A 778-16

Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products

A 888-15

Specification for Hubless Cast-iron Soil Pipe

  

and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Application

B 32-08 (2014)

Specification for Solder Metal

B 42-15a

Specification for Seamless Copper Pipe, Standard Sizes

B 43-15

Specification for Seamless Red Brass Pipe, Standard Sizes

B 75-11

Specification for Seamless Copper Tube

B 88-14

Specification for Seamless Copper Water Tube

B 152/B 152M-13

Specification for Copper Sheet, Strip Plate and Rolled Bar

B 251-10

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

B 302-12

Specification for Threadless Copper Pipe, Standard Sizes

B 306-13

Specification for Copper Drainage Tube (DWV)

B 447-12a

Specification for Welded Copper Tube

B 687-99(2016)

Specification for Brass, Copper and Chromium-plated Pipe Nipples

B 813-16

Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube

B 828-16

Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings

C 4-04(2014)

Specification for Clay Drain Tile and Perforated Clay Drain Tile

C 14-15a

Specification for Nonreinforced Concrete Sewer, Storm Drain and Culvert Pipe

C 76-15a

Specification for Reinforced Concrete Culvert, Storm Drain and Sewer Pipe

C 425-04(2013)

Specification for Compression Joints for Vitrified Clay Pipe and Fittings

C 443-12

Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets.

C 564-14

Specification for Rubber Gaskets for Cast-iron Soil Pipe and Fittings

C 700-13

Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated

C 1053-00(2015)

Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications

C 1173-10(2014)

Specification for Flexible Transition Couplings for Underground Piping System

C 1277-13

Specification for Shielded Coupling Joining Hubless Cast-iron Soil Pipe and Fittings

C 1440-08(2013)

Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems

C 1460-12

Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground

C 1461-08 (2013)

Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste and Vent (DWV) Sewer, Sanitary and Storm Plumbing Systems for Above and Below Ground Use

C 1540-15

Specification for Heavy Duty Shielded Couplings Joining Hubless Cast-iron Soil Pipe and Fittings

C 1563-13

Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent and Storm Piping Applications

D 1253-14

Standard Test Method For Residual Chlorine in Water

D 1527-99(2005)

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

D 1785-15

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

D 2235-04(2011)

Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

D 2239-12a

Specification for Polyethylene (PE) Plastic

  

Pipe (SIDR-PR) Based on Controlled Inside Diameter

D 2241-15

Specification for Poly (Vinyl Chloride) (PVC) Pressure-rated Pipe (SDR-Series)

D 2282-99(2005)

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)

D 2464-15

Specification for Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2466-15

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40

D 2467-15

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2468-96a

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40

D 2564-12

Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

D 2609-15

Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe

D 2657-15

Practice for Heat Fusion-joining of Polyolefin Pipe and Fitting Waste, and Vent Pipe and Fittings

D 2661-14

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

D 2665-14

Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

D 2672-14

Specification for Joints for IPS PVC Pipe Using Solvent Cement

D 2683-14

Standard Specification for Socket-type Polyethylene fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

D 2729-11

pecification for Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

D 2737-2012a

Specification for Polyethylene (PE) Plastic Tubing.

D 2751-05

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings

D 2846/D 2846M-14

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot and Cold Water Distribution Systems

D 2855-15

Standard Practice for Making Solvent-cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings

D 2949-10

Specification for 3.25 -in Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

D 3034-15

Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

D 3035-15

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

D 3139-98(2011)

Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

D 3212-07 (2013)

Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

D 3261-15

Specification for Butt Heat Fusion Polyethylene (PE) Plastic fittings for Polyethylene (PE) Plastic Pipe and Tubing

D 3311-11 (2016)

Specification for Drain, Waste and Vent (DWV) Plastic Fittings Patterns

D 4068-15

Specification for Chlorinated Polyethlene (CPE) Sheeting for Concealed Water-containment Membrane

D 4551-12

Specification for Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-containment Membrane

E 2727-10e1

Standard Practice for the Assessment of Rainwater Quality 1302.8.1

F 405-13

Specification for Corrugated Polyethylene (PE) Pipe and Fittings

F 409-12

Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings

F 437-15

Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 438-15

Specification for Socket-type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

F 439-13

Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 441/F 441M-15

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

F 442/F 442M-13e1

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)

F 477-14

Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

F 493-14

Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

F 628-12e2

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core

F 656-15

Specification for Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

F 714-2013

Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter

F 876-15a

Specification for Cross-linked Polyethylene (PEX) Tubing

F 877-2011a

Specification for Cross-linked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems

F 891-10

Specification for Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core

F 1055-15

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene Pipe and Tubing

F 1281-11

Specification for Cross-linked Polyethylene/Aluminum/ Cross-linked Polyethylene (PEX-AL-PEX) Pressure Pipe

F 1282-10

Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

F 1412-16

Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage

F 1476-13

Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications

F 1488-14

Specification for Coextruded Composite Pipe

F 1548-01(2012)

Standard Specification for the Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications

F 1673-10

Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems

F 1807-15

Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

F 1866-13

Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings

F 1960-15

Specification for Cold Expansion Fittings with PEX Reinforcing Rings for use with Cross-linked Polyethylene (PEX) Tubing

F 1970-12e1

Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) OR Chlorinated Poly (Vinyl Chloride) (CPVC) Systems

F 1974-15

Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure Pipe

F 1986-01(2011)

Specification for Multilayer Pipe, Type 2, Compression Fittings and Compression Joints for Hot and Cold Drinking Water Systems

F 2080-15a

Specifications for Cold-expansion Fittings with Metal Compression-sleeves for Cross-linked Polyethylene (PEX) Pipe

F 2098-15

Standard specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal and Plastic Insert Fittings

F 2159-14

Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

F 2262-09

Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Tubing OD Controlled SDR9

F 2306/F 2306M-14e1

12'' to 60'' Annular Corrugated Profile-wall Polyethylene (PE) Pipe and Fittings for Gravity Flow Storm Sewer and Subsurface Drainage Applications

F 2389-15

Specification for Pressure-rated Polypropylene (PP) Piping Systems

F 2434-14

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/ Cross-linked Polyethylene (PEX AL-PEX) Tubing

F 2735-09

Standard Specification for Plastic Insert Fittings for SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

F 2769-14

Polyethylene or Raised Temperature (PERT) Plastic Hot and Cold Water Tubing and Distribution Systems

F 2831-12

Standard Practice for Internal Non Structural

  

Epoxv Barrier Coating Material Used In Rehabilitation of Metallic Pressurized Piping Systems

F 2855-72

Specification Polv (Vinyl

ChlorideVAluminum/Polv (Vinyl Chloride)

(CPVC/AL/CPVC) Composite Pressure

Tubing

AWS American Welding Society

8669 NW 36 Street #130

Doral, FL 33166

Standard Referenced

Title

A 5.8 M/A 5.8 -2011

Specifications for Filler Metals for Brazing and Braze Welding

AWWA American Water Works Association

6666 West Quincy Avenue

Denver. CO 80235

Standard Referenced

Title

C104/A 21.4 -75

Cement-mortar Lining for Ductile-iron Pipe and Fittings for Water

C110/A 21.10 -12

Ductile-iron and Gray-iron Fittings

C111/A 21.11 -12

Rubber-gasket Joints for Ductile-iron Pressure Pipe and Fittings

C115/A 21.15 -11

Flanged Ductile-iron Pipe with Ductile-iron or Gray-iron Threaded Flanges

C151/A 21.51 -09

Ductile-iron Pipe, Centrifugally Cast for Water

C153-00/A 21.53 -11

Ductile-iron Compact Fittings for Water Service

C500-09

Standard for Metal-Seated Gate Valves for Water Supply Service

C504-15

Standard for Rubber-Seated Butterfly Valves

C507-15

Standard for Ball Valves, 6 In. Through 60 In.

C510-07

Double Check Valve Backflow Prevention Assembly

C511-07

Reduced-pressure Principle Backflow Prevention Assembly

C651-14

Disinfecting Water Mains

C652-11

Disinfection of Water-storage Facilities

C901-08

Polyethylene (PE) Pressure Pipe and Tubing 1/ inch (13 mm) Through 3 inch (76 mm) for Water Service.

C904-16

Cross-linked Polyethylene (PEX) Pressure Pipe 1/ inch (13 mm) Through 3 inch (76 mm) for Water Service

D100-11

Standard for Welded Carbon Steel Tanks for

  

Water Storage

D115-06

Standard for Tendon Prestressed-Concrete Water Tanks

D120-09

Standard for Thermosetting Fiberglass-Reinforced Plastic Tanks

CISPI Cast Iron Soil Pipe Institute

5959 Shallowford Road, Suite 419

Chattanooga, TN 37421

Standard Referenced

Title

301-12

Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

310-12

Specification for Coupling for Use in Connection with Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

CSA CSAGroup

8501 East Pleasant Valley

Cleveland, OH 44131-5516

Standard Referenced

Title

A 257.1 M-2012

Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

A 257.2 M-2012

Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

A 257.3 M-2012

Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections and Fittings Using Rubber Gaskets

ASME A112.18.1-2012/

Plumbing Supply Fittings

CSA B 125.1 -2012

  

A112.18.2-2015/

Plumbing Waste Fittings

CSA B 125.2 -2015

  

ASME A112.19.2-2013/

Ceramic Plumbing Fixtures

B 45.1 -2013

  

ASME A112.19.1-2013/

Enameled Cast-iron and Enameled Steel

CSA B 45.2 -2013

Plumbing Fixtures

ASME A112.19.3-2008/

Stainless-steel Plumbing Fixtures

CSA B 45.4 -08(R2013)

  

ASME A112.19.5-2011/

Flush Valves and Spuds for Water Closets,

CSA B 45.15 -2011

Urinals and Tanks

ASME A112.19.7-2012/

Hydromassage Bathtub Systems

CSA B 45.10 -2012

  

CSA B 45.5 -11(R2016)/

Plastic Plumbing Fixtures

IAPMO Z124-2011(R2016)

  

ASME A112.3.4-2013/

Macerating Systems and Related

CSA B 45.9 -2013

Components

CSA B 125.16 -2011

Performance Requirements for Individual Thermostatic, Pressure Balancing and Combination Control Valves for Individual Fixture Fittings

B64.1.1-11 (2016)

Vacuum Breakers, Atmospheric Type (AVB)

B64.1.2-11 (2016)

Pressure Vacuum Breakers, (PVB)

B64.1.3-11 (2016)

Spill Resistant Pressure Vacuum Breaks (SRPVB)

B 64.2 -11 (2016)

Vacuum Breakers, Hose Connection Type (HCVB)

B64.2.1-11 (2016)

Vacuum Breakers, Hose Connection (HCVB) with Manual Draining Feature

B64.2.1.1-11 (2016)

Hose Connection Dual Check Vacuum Breakers, (HCDVB)

B64.2.2-11 (2016)

Vacuum Breakers, Hose Connection Type

  

(HCVB) with Automatic Draining Feature

B 64.3 -11 (2016)

Backflow Preventers, Dual Check Valve Type with Atmospheric Port (DCAP)

B 64.4 -11 (2016)

Backflow Preventers, Reduced Pressure Principle Type (RP)

B64.4.1-11 (2016)

Reduced Pressure Principle for Fire Sprinklers (RPF)

B 64.5 -11 (2016)

Double Check Backflow Preventers (DCVA)

B64.5.1-11 (2016)

Double Check Valve Backflow Preventer for Fire Systems (DCVAF)

B 64.6 -11 (2016)

Dual Check Backflow PreventersValve (DuC)

B 64.7 -11 (2016)

Laboratory Faucet Vacuum Breakers (LFVB)

B 64.10 -11 (2016)

Manual for the Selection and Installation of Backflow Prevention Devices

B64.10.1-11 (2016)

Maintenance and Field Testing of Backflow Preventers

B79-08(R2013)

Commercial and Residential Drains, and Cleanouts

B 125.3 -2012

Plumbing Fittings

B 137.1 -13

Polyethylene (PE) Pipe, Tubing and Fittings for Cold Water Pressure Services

B 137.2 -13

Polyvinylchloride PVC Injection-moulded Gasketed Fittings for Pressure Applications

B 137.3 -13

Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications

B 137.5 -13

Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications

B 137.6 -13

CPVC Pipe, Tubing and Fittings for Hot and Cold Water Distribution Systems

B 137.9 -13

Polyethylene/Aluminum/ Polyethylene Composite Pressure Pipe Systems

B 137.10 -13

Cross-linked Polyethylene/Aluminum/ Polyethylene Composite Pressure Pipe Systems

B 137.11 -13

Polypropylene (PP-R) Pipe and Fittings for Pressure Applications

B 181.1 -15

Acrylonitrile-butadiene-styrene ABS Drain,

  

Waste and Vent Pipe and Pipe Fittings

B 181.2 -15

Polyvinylchloride PVC and chlorinated polyvinylchloride (CPVC) Drain, Waste, and Vent Pipe and Pipe Fittings

B 181.3 -15

Polyolefin and Polyvinylidene Fluoride (PVDF) Laboratory Drainage Systems

B 182.1 -15

Plastic Drain and Sewer Pipe and Pipe Fittings

B 182.2 -15

PSM Type Polyvinylchloride PVC Sewer Pipe and Fittings

B 182.4 -15

Profile Polyvinylchloride PVC Sewer Pipe and Fittings

B 182.6 -15

Profile Polyethylene (PE) Sewer Pipe and Fittings for Leak-proof Sewer Applications

B 182.8 -15

Profile Polyethylene (PE) Storm Sewer and Drainage Pipe and Fittings

B356-10 (R2015)

Water Pressure Reducing Valves for Domestic Water Systems

B 483.1 -14 B 481.1 -12

Drinking Water Treatment Units Testing and Rating of Grease interceptors Using Lard

B 481.3 -12

Sizing, Selection, Location and Installation of Grease Interceptors

B602-16

Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe

FEMA Federal Emergency Management Agency

Federal Center Plaza 500 C Street S.W.

Washington, DC 20472

Standard Referenced

Title

44 CFR Parts 59-77 (2002)

National Flood Insurance Program

IAPMO IAPMO Group

4755 E. Philadelphia

Ontario, CA 91761

Standard Referenced

Title

Z1001-2014

CSA B 45.5 -11(R2016)/ IAPMO Z124-2011(R2016)

Prefabricated Gravity Grease Interceptors Plastic Plumbing Fixtures

ICC International Code Council,Inc.500 New Jersey Ave,NW

6th Floor

Washington, DC 20001

Standard Referenced

Title

A 117.1 -2009

Accessible and Usable Buildings and

IFGC-15

Facilities International Fuel Gas Code®

ISEA InternationalSafetyEquipmentAssociation 1901 N. Moore Street, Suite 808 Arlington, VA 22209

Standard Referenced

Title

ANSI/ISEA Z 358.1 -2014

Emergency Eyewash and Shower Equipment

MSS Manufacturers Standardization Society of the Valve and Fittings

Industry, Inc. 127 Park St. NE

Vienna, VA 22180-4602

Standard Referenced

Title

SP-67-2011

Butterfly Valves

SP-70-2011

Gray Iron Gate Valves, Flanged and Threaded Ends

SP-71-2011

Gray Iron Swing Check Valves, Flanged and Threaded Ends

SP-72-2010a

Ball Valves with Flanged or Butt-Welding Ends for General Service

SP-78-2011

Cast Iron Plug Valves, Flanged and Threaded Ends

SP-80-2013

Bronze Gate, Globe, Angle and Check Valves

SP-110-2010

Ball Valves, Threaded, Socket Welded, Solder Joint, Grooved and Flared Ends

NFPA National Fire Protection Association

1 Batterymarch Park Quincy,

MA 02169-7471

Standard Referenced

Title

70-17

National Electric Code

99-15

Health Care Facilities Code

NSF NSF International

789 Dixboro Road Ann Arbor, MI 48105

Standard Referenced

Title

3-2012

Commercial Warewashing Equipment

14-2014

Plastic Piping System Components and Related Materials

18-2012

Manual Food and Beverage Dispensing Equipment 426.1

42-2015

Drinking Water Treatment Units-Aesthetic Effects

44-2015

Residential Cation Exchange Water Softeners

50-2015

Equipment for Swimming Pools, Spas, Hot Tubs and other Recreational Facilities

53-2015

Drinking Water Treatment Units-Health Effects

58-2015

Reverse Osmosis Drinking Water Treatment Systems

61-2015

Drinking Water System Components- Health Effects

62-2015

Drinking Water Distillation Systems

350-2014

Onsite Residential and Commercial Water Reuse Treatment Systems

359-2011

Valves for Crosslinked Polyethylene (PEX) Water Distribution Tubing Systems

372-2016

Drinking Water Systems Components-Lead Content

PDI Plumbing and Drainage Institute

800 Turnpike Street, Suite 300

North Andover, MA 01845

Standard Referenced

Title

PDI G101- 2015

Testing and Rating Procedure for Grease Interceptors with Appendix of Sizing and Installation Data

PDI G102- 2009

Testing and Certification for Grease Interceptors with Fog Sensing and Alarm Devices

UL UL LLC

333 Pfingsten Road

Northbrook, IL 60062-2096

Standard Referenced

Title

399-2008

Drinking-Water Coolers-with revisions through January 14, 2011

430-2015

Waste Disposers

508-99

Industrial Control Equipment-with revisions through March 2013

1795-2009

Hydromassage Bathtubs including revisions through August 23, 2011

Replaces: 4101:3-13-01

Effective: 11/1/2017
Five Year Review (FYR) Dates: 11/01/2022
Promulgated Under: 119.03
Statutory Authority: 3781.10(A)
Rule Amplifies: 3781.10 , 3781.11, 3791.04
Prior Effective Dates: 3/1/98, 4/1/99, 12/1/00, 1/1/02, 1/1/04, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08, 1/1/09, 11/1/11, 3/1/13, 7/1/14, 1/1/15, 1/1/16