LAW
Writer®
Ohio Laws and Rules
4301.2 Referenced standard list.
AAMA American Architectural Manufacturers Association
1827 Walden Office Square, Suite 550
Schaumburg, IL 60173
101/I.S2-97 Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors
101/I.S2/NAFS-02 Voluntary Performance Specification for Windows, Skylights and Glass Doors
ACI American Concrete Institute
38800 Country Club Drive
Farmington Hills, MI 48333
318-02 Building Code Requirements for Structural Concrete
530-02 Building Code Requirements for Masonry Structures
530.1-02 Specifications for Masonry Structures
ACCA Air Conditioning Contractors of America
2800 Shirlington Road, Suite 300
Arlington, VA 22206
Manual D-95 Residential Duct Systems
Manual J-87 Residential Load Calculation-Seventh Edition
AFPA American Forest and Paper Association
111 19th Street, NW, Suite 800
Washington, DC 20036
NDS-01 National Design Specification (NDS) for Wood Construction-with 2001 Supplement
WFCM-2001 Wood Frame Construction Manual for One- and Two-family Dwellings
AFPA-93 Span Tables for Joists and Rafters
T.R. No. 7-87 Basic Requirements for Permanent Wood Foundation System
AHA American Hardboard Association
1210 West Northwest Highway
Palatine, IL 60067
A135.4-95 Basic Hardboard
A135.5-95 Prefinished Hardboard Paneling
A135.6-98 Hardboard Siding
A194.1-85 Cellulosic Fiber Board
AISI American Iron and Steel Institute
1140 Connecticut Ave, Suite 705
Washington, DC 20036
Header-2001 Standard for Cold-formed Steel Framing-Header Design
PM-2001 Standard for Cold-formed Steel Framing-Prescriptive Method for One- and Two-family Dwellings
Truss-2001 Standard for Cold-formed Steel Framing-Truss Design
AITC American Institute of Timber Construction
7012 S. Revere Parkway, Suite 140
Englewood, CO 80112
AITC A 190.1-92 Structural Glued Laminated Timber
ANSI American National Standards Institute
25 West 43rd Street, Fourth Floor
New York, NY 10036
A108.1A-99 Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar
A108.1B-99 Installation of Ceramic Tile, Quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set or Latex-Portland Mortar
A108.4-99 Installation of Ceramic Tile with Organic Adhesives or Water Cleanable Tile-setting Epoxy Adhesive
A108.5-99 Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex-Portland Cement Mortar
A108.6-99 Installation of Ceramic Tile with Chemical Resistant, Water Cleanable Tile-setting and – grouting Epoxy
A108.11-99 Interior Installation of Cementitious Backer Units
A118.1-99 American National Standard Specifications for Dry-set Portland Cement Mortar
A118.3-99 American National Standard Specifications for Chemical Resistant, Water Cleanable Tilesetting and Grouting Epoxy and Water Cleanable Tile-setting Epoxy Adhesive
A136.1-99 American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile
A137.1-88 American National Standard Specifications for Ceramic Tile
A208.1-99 Particleboard
LC1-97 Interior Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing
Z21.1-00 Household Cooking Gas Appliances
Z21.5.1-99 Gas Clothes Dryers-Volume I-Type I Clothes Dryers
Z21.8-94 Installation of Domestic Gas Conversion Burners
Z21.10.1-00 Gas Water Heaters-Volume I-Storage, Water Heaters with Input Ratings of 75,000 Btu per hour or Less
Z21.10.3-98 Gas Water Heaters-Volume III-Storage, Water Heaters with Input Ratings above 75,000 Btu per hour, Circulating and Instantaneous Water Heaters-with Z21.10.3a-99 Addendum
Z21.11.1-91 Gas-fired Room Heaters-Volume I-Vented Room Heaters-with 1993 Addendum
(Replaced by Z21.86-98/CSA 2.32 – M98, Vented Gas-fired Space Heating Appliances)
Z21.11.2-96 Gas-fired Room Heaters-Volume II-Unvented Room Heaters-with Addendum A-97 and Addendum B-98
Z21.13-99 Gas-fired Low Pressure Steam and Hot Water Boilers
Z21.15-97 Manually Operated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves
Z21.22-99 Relief Valves for Hot Water Supply Systems
Z21.40.1-96 Gas-fired Heat Activated Air Conditioning and Heat Pump Appliances-with Z21.40.1a-98 Addendum
Z21.40.2-96 Gas-fired Work Activated Air Conditioning and Heat Pump Appliances (Internal Combustion)- with Z21.40.2a-97 Addendum
Z21.42-93 Gas-fired Illuminating Appliances
Z21.47-00 Gas-fired Central Furnaces-with Addendum Z21.47a-00
Z21.48-92 Gas-fired Gravity and Fan-type Floor Furnace-with Addendum A-1993
(Replaced by Z21.86-98/CSA 2.32-M98, Vented Gas-fired Space-heating Appliances)
Z21.49-92 Gas-fired Gravity and Fan-type Vented Wall Furnaces-with Addendum B-1994
(Replaced by Z21.86-98/CSA 2.32-M98, Vented Gas-fired Space-heating Appliances)
Z21.50-2000 Vented Gas Fireplaces-with Addendum A-1999 and Addendum B-1999
Z21.56-98 Gas-fired Pool Heaters-with Addendum Z21.56a-99
Z21.58-95 Outdoor Cooking Gas Appliances-with Addendum Z21.58a-1998
Z21.60-2000 Decorative Gas Appliances for Installation in Vented Fireplaces
Z21.84-99 Manually-listed, Natural Gas Decorative Gas Appliances for Installation in Solid Fuel Burning Fireplaces
Z21.86-98/CSA 2.32 M98 Gas-fired Vented Space Heating Appliances
Z21.88-99 Vented Gas Fireplace Heaters
Z83.6-90 (R 1998) Gas-fired Infrared Heaters
Z83.8-96 Gas-fired Unit Heaters-with Addendum Z83.8a-1997
Z97.1-84(R1994) Safety Glazing Materials Used in Buildings-Safety Performance Specifications and Methods of Test (Reaffirmed 1994)
Z124.1-95 Plastic Bathtub Units
Z124.2-95 Plastic Shower Receptors and Shower Stalls
Z124.3-95 Plastic Lavatories
Z124.4-96 Plastic Water Closet Bowls and Tanks
Z124.6-97 Plastic Sinks
APA APA-The Engineered Wood Association
P. O. Box 11700
Tacoma, WA 98411-0700
APA E30-01 Engineered Wood Construction Guide
ASCE American Society of Civil Engineers
1801 Alexander Bell Drive
Reston, VA 20191
5-02 Building Code Requirements for Masonry Structures
6-02 Specifications for Masonry Structures
7-02 Minimum Design Loads for Buildings and Other Structures
32-01 Design and Construction of Frost Protected Shallow Foundations
ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.
1791 Tullie Circle, NE
Atlanta, GA 30329
34-2001 Designation and Safety Classification of Refrigerants
ASHRAE-2001 ASHRAE Fundamentals Handbook-2001
ASME American Society of Mechanical Engineers
Three Park Avenue
New York, NY 10016-5990
A112.1.2-1991(R1998) Air Gaps in Plumbing Systems
A112.1.3-2000 Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances
A112.3.4-2000 Macerating Toilet Systems and Related Components
A112.4.1-1993(R1998) Water Heater Relief Valve Drain Tubes
A112.4.3-1999 Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System
A112.6.1M-1997 Floor Affixed Supports for Off-the-floor Plumbing Fixtures for Public Use
A112.6.2-2000 Framing-Affixed Supports for Off-the-floor Water Closets with Concealed Tanks
A112.6.3-2001 Floor and Trench Drains
A112.18.1-2000 Plumbing Fixture Fittings
A112.18.6-1999 Flexible Water Connectors
A112.19.1M-1994 (R1999) Enameled Cast Iron Plumbing Fixtures
A112.19.2M-1998 Vitreous China Plumbing Fixtures
A112.19.3M-1987 (R1996) Stainless Steel Plumbing Fixtures (Designed for Residential Use)
A112.19.4M-1994 (R1999) Porcelain Enameled Formed Steel Plumbing Fixtures
A112.19.5-1999 Trim for Water-closet Bowls, Tanks, and Urinals
A112.19.6-1995 Hydraulic Performance Requirements for Water Closets and Urinals
A112.19.7M-1995 Whirlpool Bathtub Appliances
A112.19.8M-1987 (R1996) Suction Fittings for Use in Swimming Pools,Wading Pools, Spas, Hot Tubs, and Whirlpool Bathtub Appliances
A112.19.9M-1998 Non-vitreous Ceramic Plumbing Fixtures
A112.19.12-2000 Wall Mounted and Pedestal Mounted, Adjustable and Pivoting Lavatory and Sink Carrier Systems
A112.19.13-2001 ElectrohydraulicWater Closets
A112.19.15-2001 Bathtub/Whirlpool Bathtubs with Pressure Sealed Doors
B1.20.1-1983(R1999) Pipe Threads, General Purpose (Inch)
B16.3-1999 Malleable Iron Threaded Fittings Classes 150 and 300
B16.4-1998 Gray-iron Threaded Fittings Classes 125 and 250
B16.9-1993 Factory-made Wrought Steel Buttwelding Fittings
B16.11-1996 Forged Fittings, Socket-welding and Threaded
B16.12-1998 Cast Iron Threaded Drainage Fittings
B16.15-1985(R1994) Cast Bronze Threaded Fittings
B16.18-1984(R1994) Cast Copper Alloy Solder Joint Pressure Fittings
B16.22-1995 Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
B16.23-1992 Cast Copper Alloy Solder Joint Drainage Fittings (DWV)
B16.26-1988 Cast Copper Alloy Fittings for Flared Copper Tubes
B16.28-1994 Wrought Steel Buttwelding Short Radius Elbows and Returns
B16.29-1994 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings-DWV
B16.33-1990 Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig (Sizes 1/2 through 2)
B36.10M-2000 Welded and Seamless Wrought-steel Pipe
BPVC-1998 Boiler and Pressure Vessel Code (Sections I, II, IV & VI)
CSD-1-1996 Controls and Safety Devices for Automatically Fired Boilers
ASSE American Society of Sanitary Engineering
28901 Clemens Road, Suite 100
Westlake, OH 44145
1001-90 Performance Requirements for Pipe Applied Atmospheric Type Vacuum Breakers
1002-99 Performance Requirements for Antisiphon Fill Valves (Ballcocks) for Gravity Water Closet Flush Tanks
1003-95 Performance Requirements for Water Pressure Reducing Valves
1006-89 Performance Requirements for Residential Use Dishwashers
1007-92 Performance Requirements for Home Laundry Equipment
1008-89 Performance Requirements for Household Food Waste Disposer Units
1010-98 Performance Requirements for Water Hammer Arresters
1011-95 Performance Requirements for Hose Connection Vacuum Breakers
1012-95 Performance Requirements for Backflow Preventers with Intermediate Atmospheric Vent
1013-99 Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Fire Protection Principle Backflow Preventers
1014-90 Performance Requirements for Hand-held Showers
1015-99 Performance Requirements For Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies
1016-96 Performance Requirements for Individual Thermostatic, Pressure Balancing and Combination Control Valves for Individual Fixture Fittings
1017-99 Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems.
1019-97 Performance Requirements for Vacuum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining Type
1020-98 Performance Requirements for Pressure Vacuum Breaker Assembly
1023-79 Performance Requirements for Hot Water Dispensers Household Storage Type Electrical
1024-98 Performance Requirements for Dual Check Valve Type Backflow Preventers
1025-78 Performance Requirements for Diverters for Plumbing Faucets with Hose Spray, Anti-siphon Type, Residential Applications
1035-95 Performance Requirements for Laboratory Faucet Backflow Preventers
1037-90 Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures
1047-99 Performance Requirements for Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies
1048-99 Performance Requirements for Double Check Detector Fire Protection Backflow Prevention Assemblies
1050-91 Performance Requirements for Air Admittance Valves for Plumbing Drainage, Waste and Vented Systems-Stack Type Device
1051-98 Performance Requirements for Air Admittance Valves for Plumbing Drainage Systems-Fixture and Branch Devices
1052-94 Performance Requirements for Hose Connection Backflow Preventer
1056-95 Performance Requirements for Back Siphonage Vacuum Breaker
1062-97 Performance Requirements for Temperature Actuated, Flow Reduction Valves to Individual Fixture Fittings
1066-97 Performance Requirements for Individual Pressure Balancing In-Line Valves for Individual Fixture Fittings
ASTM ASTM International
100 Barr Harbor Drive
West Conshohocken, PA 19428
A 36/A 36M-01 Specification for Carbon Structural Steel
A 53/A53M-01 Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless
A 74-98 Specification for Cast Iron Soil Pipe and Fittings
A 106-99e Specification for Seamless Carbon Steel Pipe for High Temperature Service
A 126-01 Specification for Gray Iron Castings for Valves, Flanges and Pipe Fittings
A 153-01a Specification for Zinc Coating (Hot Dip) on Iron and Steel Hardware
A 167-99 Specification for Stainless and Heat-resisting Chromium-nickel Steel Plate, Sheet, and Strip
A 197/A197M-00 Specification for Cupola Malleable Iron
A 254-97 Specification for Copper Brazed Steel Tubing
A 312/A 312M-01 Specification for Seamless and Welded Austenitic Stainless Steel Pipes
A 377-99 Specification for Ductile Iron Pressure Pipe
A 510M-00 Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel Metric
A 525-87 Specification for Steel Sheet Zinc-coated (Galvanized) Steel Wire
A 539-99 Specification for Electronic-resistance-welded Coiled Steel Tubing for Gas and Fuel Oil Lines
A 615/A 0615M-01b Specification for Deformed and Plain Billet-steel Bars for Concrete Reinforcement
A 641/A 0641M-98 Specification for Zinc-coated (Galvanized) Carbon Steel Wire
A 653/A 0653M-00 Specification for Steel Sheet, Zinc-coated (Galvanized) or Zinc-iron Alloy-coated (Galvanized) by the Hot-dip Process
A 706M-00 Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement
A 755M-99 Specification for Steel Sheet, Metallic Coated by the Hot-dip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products
A 778-01 Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products
A 792M-99 Specification for Steel Sheet, 55% Aluminum-zinc Alloy-coated by the Hot-dip Process
A 875/0875M-01a Specification for Steel Sheet, Zinc-5%, Aluminum Alloy-coated by the Hot-dip Process
A 888-98e1 Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Application
A 951-00 Specification for Masonry Joint Reinforcement
A 996/A 996M-00 Specifications for Rail-steel and Axel-steel Deformed Bars Reinforcement for Concrete
B 32-00 Specification for Solder Metal
B 42-98 Specification for Seamless Copper Pipe, Standard Sizes
B 43-98 Specification for Seamless Red Brass Pipe, Standard Sizes
B 75-99 Specification for Seamless Copper Tube
B 88-99e1 Specification for Seamless Copper Water Tube
B 101-96 Specification for Lead-coated Copper Sheet and Strip for Building Construction
B 135-00 Specification for Seamless Brass Tube (Metric)
B 209-96 Specification for Aluminum and Aluminum-alloy Sheet and Plate
B 227-98 Specification for Hard-drawn Copper-clad Steel Wire
B 251-97 Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube
B 280-99 Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
B 302-00 Specification for Threadless Copper Pipe, Standard Sizes
B 306-99 Specification for Copper Drainage Tube (DWV)
B 370-98 Specification for Copper Sheet and Strip for Building Construction
B 447-00 Specification for Welded Copper Tube
B 633-98e01 Specification for Electrodeposited Coatings of Zinc on Iron and Steel
B 813-00e01 Specification for Liquid and Paste Fluxes for Soldering Applications of Copper and Copper Alloy Tube
B 828-00 Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings
C 5-79(97) Specification for Quicklime for Structural Purposes
C 14-99 Specification for Concrete Sewer, Storm Drain, and Culvert Pipe
C 27-98 Classification of Fireclay and High-alumina Refractory Brick
C 28/C28M-00 Specification for Gypsum Plasters
C 34-96(2001) Specification for Structural Clay Load-bearing Wall Tile
C 35-95(2001) Specification for Inorganic Aggregates for Use in Gypsum Plaster
C 36/C 0036M-01 Specification for Gypsum Wallboard
C 37/C 0037M-01 Specification for Gypsum Lath
C 55-01 Specification for Concrete Brick
C 59/C 0059M-00 Specification for Gypsum Casting and Molding Plaster
C 61/C 0061M-00 Specification for Gypsum Keene’s Cement
C 62-01 Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)
C 73-99a Specification for Calcium Silicate Face Brick (Sand Lime Brick)
C 79-01 Specification for Treated Core and Nontreated Core Gypsum Sheathing Board
C 90-01 Specification for Load-bearing Concrete Masonry Units
C 129-01 Specification for Nonload-bearing Concrete Masonry Units and Related Units
C 143/C 0143M-00 Test Method for Slump or Hydraulic Cement Concrete
C 145-85 Specification for Solid Load-bearing Concrete Masonry Units
C 199-84(2000) Test Method for Pier Test for Refractory Mortar
C 207-97 Specification for Hydrated Lime for Masonry Purposes
C 208-95(2001) Specification for Cellulosic Fiber Insulating Board
C 216-01a Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
C 236-89 (1993)e1 Test Method for Steady-State Thermal Performance of Building Assemblies by Means of a Guarded Hot Box
C 270-01a Specification for Mortar for Unit Masonry
C 296-00 Specification for Asbestos Cement Pressure Pipe
C 315-00 Specification for Clay Flue Linings
C 406-00 Specifications for Roofing Slate
C 411-97 Test Method for Hot-surface Performance of High-temperature Thermal Insulation
C 425-01 Specification for Compression Joints for Vitrified Clay Pipe and Fittings
C 443-01 Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets
C 475-01 Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard
C 476-01 Specification for Grout for Masonry
C 514-01 Specification for Nails for the Application of Gypsum Wallboard
C 557-99 Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing
C 578-01 Specification for Rigid, Cellular Polystyrene Thermal Insulation
C 587-97 Specification for Gypsum Veneer Plaster
C 588/C0588M-99 Specification for Gypsum Base for Veneer Plasters
C 630/0630M-01 Specification for Water-resistant Gypsum Backing Board
C 631-(2000) Specification for Bonding Compounds for Interior Gypsum Plastering
C 645-00 Specification for Nonstructural Steel Framing Members
C 652-01a Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)
C 700-00 Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated
C 836-00 Specification for High Solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course
C 843-99 Specification for Application of Gypsum Veneer Plaster
C 844-99 Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
C 847-(2000) Specification for Metal Lath
C 887-79(96)e1 Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar
C 897-00 Specification for Aggregate for Job-mixed Portland Cement-based Plasters
C 931-97 Specification for Exterior Gypsum Soffit Board
C 933-96a(2001) Specification for Welded Wire Lath
C 954-00 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness
C 955-01 Specification for Load-Bearing Transverse and Axial Steel Studs, Runners Tracks, and Bracing or Bridging for Screw Application of Gypsum Panel Products and Metal Plaster Bases
C 957-93(1998) Specification for High-solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Integral Wearing Surface
C 960-01 Specification for Predecorated Gypsum Board
C 976-90(1996)e1 Test Method for Thermal Performance of Building Assemblies by Means of a Calibrated Hot Box
C 1002-01 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases
C 1029-96 Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation
C 1032-96 Specification for Woven Wire Plaster Base
C 1047-99 Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
C 1063-99 Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster
C 1157-00a Performance Specification for Hydraulic Cements
C 1167-96 Specification for Clay Roof Tiles
C 1173-97 Specification for Flexible Transition Couplings for Underground Piping Systems
C 1177/C 1177M-01 Specification for Glass Mat Gypsum Substrate for Use as Sheathing
C 1178/C 1178M-01 Specification for Glass Mat Water-resistant Gypsum Backing Panel
C 1186-99 Specification for Flat Nonasbestos Fiber Cement Sheets
C 1261-98 Specification for Firebox Brick for Residential Fireplaces
C 1277-97 Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
C 1278/C 1278M-01 Specification for Fiber-reinforced Gypsum Panels
C 1283-00e01 Practice for Installing Clay Flue Lining
C 1395/C 1395M-01 Specification for Gypsum Ceiling Board
C 1396-99 Specification for Gypsum Board
C 1460-00 Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground
C 1461-00 Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV) Sewer, Sanitary and Storm Plumbing Systems for Above and Below Ground Use
C 1492-01 Specification for Concrete Roof Tile
D 41-e01 Specification for Asphalt Primer Used in Roofing, Dampproofing, and Waterproofing
D 43-00 Specification for Coal Tar Primer Used in Roofing, Damproofing and Waterproofing
D 224-89(1996) Specification for Smooth-surfaced Asphalt Roll Roofing (Organic Felt)
D 225-01 Specification for Asphalt Shingles (Organic Felt) Surfaced with Mineral Granules
D 226-97a Specification for Asphalt-saturated (Organic Felt) Used in Roofing and Waterproofing
D 227-97a Specification for Coal Tar Saturated (Organic Felt) Used in Roofing and Waterproofing
D 249-89(96) Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules
D 0312-00 Specification for Asphalt Used in Roofing
D 371-89(1996) Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules: Wideselvage
D 422-63(1998) Test Method for Particle-size Analysis of Soils
D 449-89(1999)e01 Specification for Asphalt Used in Dampproofing and Waterproofing
D 450-(00)e1 Specification for Coal-tar Pitch Used in Roofing , Dampproofing and Waterproofing
D 1227-00 Specification for Emulsified Asphalt Used as a Protective Coating for Roofing
D 1248-00a Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
D 1527-99 Specification for Acrylonite-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80
D 1693-01 Test Method for Environmental Stress-cracking of Ethylene Plastics
D 1784-99a Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
D 1785-99 Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120
D 1863-93(2000) Specification for Mineral Aggregate Used in Built-up Roofs
D 1869-95(2000) Specification for Rubber Rings for Asbestos-cement Pipe
D 1970-01 Specification for Self-adhering Polymer Modified Bitumen Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection
D 2104-01 Specification for Polyethylene (PE) Plastic Pipe, Schedule 40
D 2178-97a Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
D 2235-01 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
D 2239-01 Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
D 2241-00 Specification for Poly (Vinyl Chloride) (PVC) Pressure-rated Pipe (SDR-Series)
D 2282-99 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)
D 2412-96a Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallelplate Loading
D 2447-01 Specification for Polyethylene (PE) Plastic Pipe Schedules 40 and 80, Based on Outside Diameter
D 2464-99 Specification for Threaded Poly (Vinly Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
D 2466-01 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
D 2467-99 Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
D 2468-96a Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40
D 2513-01a Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
D 2564-96a Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems
D 2609-00 Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
D 2626-97b Specification for Asphalt-saturated and Coated Organic Felt Base Sheet Used in Roofing
D 2661-01 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
D 2662-96a Specification for Polybutylene (PB) Plastic Pipe (SDR-PR) Based on Controlled Inside Diameter
D 2665-01 Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D 2666-96a Specification for Polybutylene (PB) Plastic Tubing
D 2672-96a Specification for Joints for IPS PVC Pipe Using Solvent Cement
D 2683-98 Specification for Socket-type Polyethylene Fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing
D 2737-01 Specification for Polyethylene (PE) Plastic Tubing
D 2751-96a Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings
D 2822-91(1997)e1 Specification for Asphalt Roof Cement
D 2823-90(1997)e1 Specification for Asphalt Roof Coatings
D 2824-94 Specification for Aluminum-pigmented Asphalt Roof Coatings, Non-fibered, Asbestos Fibered, and Fibered without Asbestos
D 2837-98a Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
D 2846/D 2846M-99 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold-water Distribution Systems
D 2898-94(1999) Test Methods for Accelerated Weathering of Fire-retardant-treated Wood for Fire Testing
D 2949-00a Specification for 3.25-in. Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D 3019-e01 Specification for Lap Cement Used with Asphalt Roll Roofing, Non-fibered, Asbestos Fibered, and Non-asbestos Fibered
D 3034-00 Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D 3035-01 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based On Controlled Outside Diameter
D 3161-99a Test Method for Wind Resistance of Asphalt Shingles (Fan Induced Method)
D 3201-94(1998)el Test Method for Hygroscopic Properties of Fire-retardant Wood and Wood-base Products
D 3212-96a Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D 3309-96a Specification for Polybutylene (PB) Plastic Hot- and Cold-water Distribution Systems
D 3350-01 Specification for Polyethylene Plastic Pipe and Fitting Materials
D 3462-01e01 Specification for Asphalt Shingles Made From Glass Felt and Surfaced with Mineral Granules
D 3468-99 Specification for Liquid-applied Neoprene and Chlorosulfanated Polyethylene Used in Roofing and Waterproofing
D 3679-01c Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding
D 3737-99 Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
D 3747-e01 Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation
D 3909-97b Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
D 4022-94(00)e1 Specification for Coal Tar Roof Cement, Asbestos Containing
D 4068-01 Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water Containment Membrane
D 4318-00 Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils
D 4434-96 Specification for Poly (Vinyl Chloride) Sheet Roofing
D 4479-00 Specification for Asphalt Roof Coatings-Asbestos-free
D 4586-00 Specification for Asphalt Roof Cement-Asbestos-free
D 4601-98 Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing
D 4637-96 Specification for EPDM Sheet Used in Single-ply Roof Membrane
D 4829-95 Test Method for Expansion Index of Soils
D 4869-88(1993)e1 Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing
D 4897-01 Specification for Asphalt Coated Glass-fiber Venting Base Sheet Used in Roofing
D 4990-97a Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing
D 5019-96 Specification for Reinforced Non-vulcanized Polymeric Sheet Used in Roofing Membrane
D 5055-00 Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood IJoists
D 5516-99a Test Method for Evaluating the Flexural Properties of Fire-retardant-treated Softwood Plywood Exposed to the Elevated Temperatures
D 5643-94(00)e1 Specification for Coal Tar Roof Cement Asbestos-free
D 5664-01 Test Methods For Evaluating the Effects of Fire-retardant Treatments and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber
D 5665-99a Specification for Thermoplastic Fabrics Used in Cold-applied Roofing and Waterproofing
D 5726-98 Specification for Thermoplastic Fabrics Used in Hot-applied Roofing and Waterproofing
D 6083-97a Specification for Liquid Applied Acrylic Coating Used in Roofing
D 6162-00a Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
D 6163-00 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements
D 6164-00 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements
D 6221-00 Specification for Reinforced Bituminous Flashing Sheets for Roofing and Waterproofing
D 6222-00e01 Specification for Atactic Polypropelene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcement
D 6223-00e01 Specification for Atactic Polypropelene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcement
D 6298-98 Specification for Fiberglass Reinforced Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface
D 6305-98e1 Practice for Calculating Bending Strength Design Adjustment Factors for Fire-Retardant-Treated Plywood Roof Sheathing
E 84-01 Test Method for Surface Burning Characteristics of Building Materials
E 96-00 Test Method for Water Vapor Transmission of Materials
E 108-99 Test Methods for Fire Tests of Roof Coverings
E 119-00a Test Methods for Fire Tests of Building Construction and Materials
E 136-99 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C
E 152-95 Methods of Fire Tests of Door Assemblies
E 330-97e1 Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference
E 814-00 Test Method for Fire Tests of Through-penetration Firestops
E 970-00 Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
E 1602-94 Guide for Construction of Solid Fuel Burning Masonry Heaters
E 1886-97 Test Method for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Missles and Exposed to Cyclic Pressure Differentials
E 1996-01 Specification for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
F 409-99a Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings
F 437-99 Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
F 438-01 Specification for Socket-type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40
F 439-01 Specification for Socket-type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
F 441/F 441M-99 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80
F 442/F 442M-99 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)
F 477-99 Specification for Elastomeric Seals (Gaskets) for joining Plastic Pipe
F 493-97 Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
F 628-01 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core
F 656-96a Specification for Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings
F 714-00 Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter
F 789-95a Specification for Type PS-46 and Type PS-115 Poly (Vinyl Chloride) (PVC) Plastic Gravity Flow Sewer Pipe and Fittings
F 876-00 Specification for Cross-linked Polyethylene (PEX) Tubing
F 877-00 Specification for Cross-linked Polyethylene (PEX) Plastic Hot- and Cold-water Distribution Systems
F 891-00 Specification for Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core
F 1055-98 Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Fittings
F 1281-e01 Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-ALPEX) Pressure Pipe
F 1282-01a Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe
F 1488-00 Specification for Coextruded Composite Pipe
F 1667-01a Specification for Driven Fasteners, Nails, Spikes, and Staples.
F 1807-99 Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing
F 1960-99 Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Crosslinked Polyethylene (PEX) Tubing
F 1974-00 Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
F 2080-01 Specification for Cold-expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe
AWPA American Wood-Preservers’ Association
P.O. Box 5690
Granbury, Texas 76049
C1-00 All Timber Products – Preservative Treatment by Pressure Processes
C2-01 Lumber, Timbers, Bridge Ties and Mine Ties – Preservative Treatment by Pressure Processes
C3-99 Piles – Preservative Treatment by Pressure Processes
C4-99 Poles – Preservative Treatment by Pressure Processes
C9-00 Plywood – Preservative Treatment by Pressure Processes
C15-00 Wood for Commercial-Residential Construction Preservative Treatment by Pressure Process
C18-99 Standard for Pressure Treated Material in Marine Construction
C20-99 Structural Lumber-Fire-retardant Treatment by Pressure Processes
C22-96 Lumber and Plywood for Permanent Wood Foundations-Preservative Treatment by Pressure Processes
C23-00 Round Poles and Posts Used in Building Construction-Preservative Treatment by Pressure Processes
C24-96 Sawn Timber Used to Support Residential and Commercial Structures
C27-88 Plywood-Fire-retardant Treatment by Pressure Process
C28-99 Standard for Preservative Treatment by Pressure Process of Structural Glued Laminated Members and Laminations Before Gluing
C31-01 Lumber Used Out of Contact With the Ground and Continuously Protected From Liquid Water-Treatment by Pressure Processes
C33-00 Standard for Preservative Treatment of Structural Composite Lumber by Pressure Processes
M4-01 Standard for the Care of Preservative-treated Wood Products
P1/P13-01 Standard for Creosote Preservative
P2-01 Standard for Creosote Solutions
P3 — 01 Standard for Creosote-petroleum Solutions
AWWA American Water Works Association
6666 West Quincy Avenue
Denver, CO 80235
C110-98 Standard for Ductile-iron and Gray-iron Fittings, 3 Inches through 48 Inches, for Water
C115-99 Standard for Flanged Ductile-iron Pipe with Ductile-iron or Gray-iron Threaded Flanges
C151-96 Standard for Ductile-iron Pipe, Centrifugally Cast, for Water
C153-00 Standard for Ductile-iron Compact Fittings for Water Service
C510-00 Double Check Valve Backflow Prevention Assembly
C511-00 Reduced-Pressure Principle Backflow Prevention Assembly
CDA The Copper Development Association, Inc.
260 Madison Avenue
New York, NY 10016
4050 Copper in Architecture-Design Handbook
CGSB Canadian General Standards Board
Place du Portage 111, 6B1
11 Laurier Street
Gatineau, Quebec, Canada KIA 1G6
37-GP-52M-(1984) Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric
37-GP-56M-(1980) Membrane, Modified Bituminous, Prefabricated and Reinforced for Roofing- with December 1985 Amendment
CAN/CGSB-37.54-95 Polyvinyl Chloride Roofing and Waterproofing Membrane
CISPI Cast Iron Soil Pipe Institute
5959 Shallowford Road, Suite 419
Chattanooga, TN 37421
301-97 Standard Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications
310-97 Standard Specification for Coupling for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
CPSC Consumer Product Safety Commission
4330 East West Highway
Bethesda, MD 20814-4408
16 CFR Part 1201-(1977) Safety Standard for Architectural Glazing
16 CFR Part 1209-(1979) Interim Safety Standard for Cellulose Insulation
16 CFR Part 1404-(1979) Cellulose Insulation
CSA Canadian Standards Association
178 Rexdale Blvd.
Rexdale (Toronto), Ontario, Canada M9W IR3
8-93 Requirements for Gas Fired Log Lighters for Wood Burning Fireplaces-with Revisions through January 1999
0325.0-92 Construction Sheathing (Reaffirmed 1998)
0437-Series-93 Standards on OSB andWaferboard (Reaffirmed 2001)
B45.1-99 Ceramic Plumbing Fixtures
B45.2-99 Enameled Cast Iron Plumbing Fixtures
B45.3-99 Porcelain Enameled Steel Plumbing Fixtures
B45.4-99 Stainless Steel Plumbing Fixtures
B45.5-99 Plastic Plumbing Fixtures
B45.9-99 Macerating Systems and Related Components
B64.7-94 Vacuum Breakers, Laboratory Faucet Type (LFVB)
B137.1-99 Polyethylene Pipe, Tubing and Fittings for Cold Water Pressure Services
B137.2-99 PVC Injection-moulded Gasketed Fittings for Pressure Applications
B137.3-99 Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications
B137.5-99 Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications-with Revisions through September 1992
B137.6-99 CPVC Pipe, Tubing and Fittings For Hot and Cold Water Distribution Systems-with Revisions through May 1986
LC3-00 Appliance Stands and Drain Pans
CAN3-B137.8M-99 Polybutylene (PB) Piping for Pressure Applications-with Revisions through July 1992
CAN/CSA A257.3M-92 Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections, and Fittings Using Rubber Gaskets
CAN/CSA B64.1.1-01 Vacuum Breakers, Atmospheric Type (AVB)
CAN/CSA B64.2-01 Vacuum Breakers, Hose Connection Type (HCVP)
CAN/CSA B64.2.2-01 Vacuum Breakers, Hose Connection Type (HCVP) with Automatic Draining Feature
CAN/CSA B64.3-01 Backflow Preventers, Dual Check Valve Type with Atmospheric Port (DCAP)
CAN/CSA B64.4-01 Backflow Preventers, Reduced Pressure Principle Type (RP)
CAN/CSA B137.9-99 Polyethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems
CAN/CSA B137.10M-99 Crosslinked Polethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems
CAN/CSA B602-99 Mechanical Couplings for Drain, Waste, and Vent Pipe and Sewer Pipe
CSSB Cedar Shake & Shingle Bureau
515 116th Avenue, NE, #275
Bellevue, WA 98004-5294
CSSB-97 Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau
CSSB-97 Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau
DOC United States Department of Commerce
100 Bureau Drive Stop 3460
Gaithersburg, MD 20899
PS 1-95 Construction and Industrial Plywood
PS 2-92 Performance Standard for Wood-based Structural-use Panels
PS 20-99 American Softwood Lumber Standard
DOTn Department of Transportation
400 Seventh St. S.W.
Washington, DC 20590
49 CFR,Parts 192.281(e) &192.283 (b) Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards
FEMA Federal Emergency Management Agency
500 C Street, SW
Washington, DC 20472
TB-2-93 Flood-resistant Materials Requirements
TB-11-01 Crawlspace Construction for Buildings Located in Special Flood Hazard Area
FM Factory Mutual
Standards Laboratories Department
1151 Boston Providence Turnpike
Norwood, MA 02062
4450-(1989) Approval Standard for Class 1 Insulated Steel Deck Roofs-with Supplements through July 1992
4880-(2001) American National Standard for Evaluating Insulated Wall or Wall and Roof/Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels,Wall/Ceiling Coating Systems, Interior or Exterior Finish Systems
GA Gypsum Association
810 First Street, Northeast, Suite 510
Washington, DC 20002-4268
GA-253-99 Recommended Standard Specification for the Application of Gypsum Sheathing
HPVA Hardwood Plywood & Veneer Association
1825 Michael Faraday Drive
Reston, Virginia 20190-5350
HP-1-2000 The American National Standard for Hardwood and Decorative Plywood
ICC International Code Council
5203 Leesburg Pike, Suite 600
Falls Church, VA 22041
IECC-06 International Energy Conservation CodeŽ
IFGC-03 International Fuel Gas CodeŽ
IPSDC-03 International Private Sewage Disposal CodeŽ
SBCCI SSTD 10-99 Standard for Hurricane Resistant Construction
MSS Manufacturers Standardization Society of the Valve and Fittings Industry
127 Park Street, Northeast
Vienna, VA 22180
SP-58-93 Pipe Hangers and Supports-Materials, Design and Manufacture
NAIMA North American Insulation Manufacturers Association
44 Canal Center Plaza, Suite 310
Alexandria, VA 22314
AH 116 06-02 Fibrous Glass Duct Construction Standards
NCMA National Concrete Masonry Association
2302 Horse Pen Road
Herndon, VA 20171-3499
TR 68-A-75 Design and Construction of Plain and Reinforced Concrete Masonry and Basement and Foundation Walls
NFPA National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
13-99 Installation of Sprinkler Systems
13D-99 Installation of Sprinkler Systems in One- and Two-family Dwellings and Manufactured Homes
13R-99 Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height
31-01 Installation of Oil-burning Equipment
58-01 Liquefied Petroleum Gas Code
70-08 National Electrical Code
72-99 National Fire Alarm Code
85-01 Boiler and Construction Systems Hazards Code
259-98 Standard Test Method for Potential Heat of Building Materials
286-00 Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth
501-99 Standard on Manufactured Housing
853-00 Standard for the Installation of Stationary Fuel Cell Power Plants
NFRC National Fenestration Rating Council, Inc.
8484 Georgia Avenue, Suite 320
Silver Spring, MD 20910
100-2001 Procedure for Determining Fenestration Product U-factors
200-2001 Procedure for Determining Fenestration product Solar Heat Gain Coefficients and Visible
Transmittance at Normal Incidence
400-2001 Procedure for Determining Fenestration Product Air Leakage
NSF NSF International
789 N. Dixboro Road
Ann Arbor, MI 48105
14-1999 Plastic Piping System Components and Related Materials
42-2000 Drinking Water Treatment Units-Anesthetic Effects
44-2001 Residential Cation Exchange Water Softeners
53-2001 Drinking Water Treatment Units-Health Effects
58-2001 Reverse Osmosis Drinking Water Treatment Systems
61-2001 Drinking Water System Components-Health Effects
RMA Rubber Manufacturer’s Association
1400 K Street N.W., Suite 900
Washington, DC 20005
RP1-90 Minimum Requirements for Non-Reinforced Black EPDM Rubber Sheets
RP2-90 Minimum Requirements for Fabric-Reinforced Black EPDM Rubber Sheets
RP3-85 Minimum Requirements for Fabric-Reinforced Black Polychloroprene Rubber Sheets
SAE Society of Automotive Engineers
400 Commonwealth Drive
Warrendale, PA 15096
J 78-(1998) Steel Self-drilling Tapping Screws
SMACNA Sheet Metal & Air Conditioning Contractors National Assoc., Inc.
4021 Lafayette Center Road
Chantilly, VA 22021
SMACNA-92 Fibrous Glass Duct Construction Standards
TMS The Masonry Society
3970 Broadway, Suite 201-D
Boulder, CO 80304
402-02 Building Code Requirements for Masonry Structures
602-02 Specification for Masonry Structures
TPI Truss Plate Institute
583 D’Onofrio Drive, Suite 200
Madison, WI 53719
TPI 1-2002 National Design Standard for Metal-plate-connected Wood Truss Construction
UL Underwriters Laboratories, Inc.
333 Pfingsten Road
Northbrook, IL 60062
17-94 Vent or Chimney Connector Dampers for Oil-fired Appliances-with Revisions through September 1999
58-96 Steel Underground Tanks for Flammable and Combustible Liquids-with Revisions through July 1998
80-96 Steel Inside Tanks for Oil-burner Fuel
103-98 Factory-built Chimneys for Residential Type and Building Heating Appliances-with Revision through March 1999
127-99 Factory-built Fireplaces-with Revisions through November 1999
174-98 Household Electric Storage Tank Water Heaters-with Revisions through October 1999
181-96 Factory-made Air Ducts and Air Connectors-with Revisions through December 1998
181A-95 Closure Systems for Use with Rigid Air Ducts and Air Connectors- with Revisions through December 1998
181B-98 Closure Systems for Use with Flexible Air Ducts and Air Connectors- with Revisions through December 1998
325-95 Door, Drapery, Louver and Window Operations and Systems-with Revisions through June 2001
343-97 Pumps for Oil-Burning Appliances-with Revisions through December 22, 1999
441-98 Gas Vents
536-97 Flexible Metallic Hose-with Revisions through October 2000
641-95 Type L, Low-temperature Venting Systems-with Revisions through April 1999
726-98 Oil-fired Boiler Assemblies-with Revisions through January 1999
727-98 Oil-fired Central Furnaces-with Revisions through January 1999
729-98 Oil-fired Floor Furnaces-with Revisions through January 1999
730-98 Oil-fired Wall Furnaces-with Revisions through January 1999
732-95 Oil-fired Storage Tank Water Heaters-with Revisions through January 1999
737-96 Fireplaces Stoves-with Revisions through May 1998
790-98 Tests for Fire Resistance of Roof Covering Materials-with Revisions through July 1998
795-99 Commercial-Industrial Gas Heating Equipment
834-98 Heating, Water Supply, and Power-Electric-with Revisions through November 1998
896-93 Oil-burning Stoves-with Revisions through November 1999
959-01 Medium Heat Appliance Factory-built Chimneys
923-95 Microwave Cooking Appliances-with Revisions through July 20, 1998
1040-96 Fire Test of Insulated Wall Construction-with Revisions through April 2001
1256-98 Fire Test of Roof Deck Construction-with Revisions through March 2000
1261-96 Electric Water Heaters for Pools and Tubs-with Revisions through November 25, 1998
1453-95 Electronic Booster and Commercial Storage Tank Water Heaters-with Revisions through September 1998
1479-94 Fire Tests of Through-Penetration Firestops
1482-98 Solid-fuel Type Room Heaters-with Revisions through January 2000
1715-97 Fire Test of Interior Finish Material
1738-00 Venting Systems for Gas-burning Appliances, Categories II, III and IV-with Revisions through December 2000
1777-98 Chimney Liners-with Revisions through July 1998
1995-98 Heating and Cooling Equipment-with Revisions through August 1999
2158A-96 Outline of Investigation for Clothes Dryer Transition Duct
ULC Underwriters’ Laboratories of Canada
7 Crouse Road
Scarborough, Ontario, Canada MIR 3A9
S 102-M88 Surface Burning Characteristics of Building Materials and Assemblies
WDMA Window & Door Manufacturers Association
1400 East Touhy Avenue, Suite 470
Des Plaines, IL 60018
101/I.S. 2-97 Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors
101/I.S.2/NAFS-02 Voluntary Performance Specification for Windows, Skylights and Glass Doors
Effective: 01/01/2009
R.C. 119.032 review dates: 05/27/2011
Promulgated Under: 119.03
Statutory Authority: 3781.10(A)
Rule Amplifies: 3781.10, 3781.11, 3791.04
Prior Effective Dates: 5/27/06, 1/1/08, 3/31/08 (Emer.), 6/24/08