Chapter 4101:3-13 Referenced Standards

4101:3-13-01 Referenced standards.

1301.1 General. This chapter lists the codes and standards that are referenced in various sections of this document. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date, and the title. The application of the referenced standards shall be as specified in Section 102.5 of the building code.

1301.2 Referenced codes. When indicated in the "OPC", the following codes refer to provisions in the listed chapters of the Administrative Code:

Referenced code

Ohio Administrative Code chapters

Building Code

4101:1-1 to 4101:1-35

Fire Code

1301:7-1 to 1301:7-7

Mechanical Code

4101:2-1 to 4101:2-15

Ohio Boiler and Pressure Vessel Rules

4101:4-1 to 4101:4-10

1301.3 Referenced Standards.

ANSIAmerican National Standards Institute

25 West 43rd Street, Fourth Floor

New York, NY 10036

Standard Referenced

Title

A 118.10 -10

Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin Set Ceramic Tile and Dimension Stone Installation

Z 4.3 -95 (R2005)

Minimum Requirements for Nonsewered Waste-Disposal Systems (Standard is developed by the Portable SanitationAssociation International-PSAI)

Z 21.22 -99 (R2003)

Relief Valves for Hot Water Supply Systems with Addenda Z 21.22 a-2000 (R2003) and Z 21.22 b-2001 (R2003) (Standardis developed by the Canadian Standards Association-CSA andis the same as CSA 4.4 -M99)

Z 124.1.2-05

Plastic Bathtub and Shower Units (Standard is developed byIAPMO)

Z 124.3 -05

Plastic Lavatories (Standard is developed by IAPMO)

Z 124.4 -06

Plastic Water Closet Bowls and Tanks (Standard is developedby IAPMO)

Z 124.6 -07

Plastic Sinks (Standard is developed by IAPMO)

Z 124.9 -04

Plastic Urinal Fixtures. (Standard is developed by IAPMO)

AHRI Air-Conditioning, Heating, & Refrigeration Institute

4100 North Fairfax Drive, Suite 200

Arlington, VA 22203

Standard Referenced

Title

1010-02 Coolers

Self-contained, Mechanically Refrigerated Drinking-Water

ASMEAmerican Society of Mechanical Engineers Three

Park Avenue

New York, NY 10016-5990

Standard Referenced

Title

A112.1.2-2004

Air Gaps in Plumbing Systems

A112.1.3-2000 (R 2005)

Air Gap Fittings for Use with Plumbing Fixtures, Appliances and Appurtenances

A112.3.1-2007

Stainless Steel Drainage Systems for Sanitary, DWV, Storm and Vacuum Applications Above and Below Ground

A112.3.4-2000 (R 2004)

Macerating Toilet Systems and Related Components

A112.4.1-2009

Water Heater Relief Valve Drain Tubes

A112.4.3-1999 (R 2004)

Plastic Fittings for Connecting Water Closets to the Sanitary Drainage System

A112.6.1M-1997 (R2002)

Floor-affixed Supports for Off-the-floor Plumbing Fixtures for Public Use

A112.6.2-2000 (R2004)

Framing-affixed Supports for Off-the-floor Water Closets with Concealed Tanks

A112.6.3-2001 (R 2007)

2001 Floor and Trench Drains

A112.6.7-2001 (R 2007)

Enameled and Epoxy-coated Cast-iron and PVC Plastic Sanitary Floor Sinks

A112.14.1-2003

Backwater Valves

A112.14.3-2000

Grease Interceptors

A112.14.4-2001(R2007)

Grease Removal Devices

A112.18.1-2005

Plumbing Supply Fittings

CSA B 125.1 -2005/A112.18.2-2005

Plumbing Waste Fittings

CSA B 125.2 -2005/A112.18.3-2002

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

A112.18.6-2009

Flexible Water Connectors.

A112.18.7-1999 (R2004)

Deck mounted Bath/Shower Transfer Valves with Integral Backflow Protection

A112.19.1M-2008

Enameled Cast Iron Plumbing Fixtures

A112.19.2-2008

Vitreous China Plumbing Fixtures and Hydraulic Requirements for Water Closets and Urinals .

A112.19.3M-2008

Stainless Steel Plumbing Fixtures (Designed for Residential Use

A112.19.4M-1994 (R 2004)

Porcelain Enameled Formed Steel Plumbing Fixtures.

A112.19.5-2005

Trim for Water-closet Bowls, Tanks and Urinals

A112.19.6-1995

Hydraulic Performance Requirements for Water Closets and Urinals

A112.19.7M-2006

HydromassageBathtub Appliances

A112.19.8M-2007

Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, Hot Tubs

A112.19.9M-1991(R2002)

Nonvitreous Ceramic Plumbing Fixtures with 2002 Supplement

A112.19.12-2006

Wall Mounted and Pedestal Mounted, Adjustable, Elevating, Tilting and Pivoting Lavatory, Sink and Shampoo Bowl Carrier Systems and Drain Systems

A112.19.13-2001 (R2007)

ElectrohydraulicWater Closets

A112.19.15- 2005

Bathtub/Whirlpool Bathtubs with Pressure Sealed Doors

A112.19.19-2006

Vitreous ChinaNonwaterUrinals

A112.21.2M-1983

Roof Drains

A112.36.2M-1991(R2002)

Cleanouts

B1.20.1-1983(R2006)

Pipe Threads, General Purpose (inch

B 16.3 -2006

Malleable Iron Threaded Fittings Classes 150 and 300

B 16.4 -2006

Gray Iron Threaded Fittings Classes 125 and 250

B 16.9 -2007

Factory-made Wrought Steel Buttwelding Fittings.

B 16.11 -2009

Forged Fittings, Socket-welding and Threaded.

B 16.12 -2009

Cast-iron Threaded Drainage Fittings

B 16.15 -2006

Cast Bronze Threaded Fittings

B 16.18 -2001(R 2005)

Cast Copper Alloy Solder Joint Pressure Fittings

B 16.22 -2001 (R2005)

Wrought Copper and Copper Alloy Solder Joint Pressure Fittings

B 16.23 -2002 (R 2006)

Cast Copper Alloy Solder Joint Drainage Fittings DWV

B 16.26 -2006

Cast Copper Alloy Fittings for Flared Copper Tubes .

B 16.28 -1994

Wrought Steel Buttwelding Short Radius Elbows and Returns

B 16.29 -2007

Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings (DWV)

BPVC Section IX- 2010

Welding and Brazing Qualifications.

ASSEAmerican Society of Sanitary Engineering

901 Canterbury Road, Suite A

Westlake, OH 44145

Standard Referenced

Title

1001-08

Performance Requirements for Atmospheric Type Vacuum Breakers

1002-08

Performance Requirements for Antisiphon Fill Valves (Ballcocks) for Gravity Water Closet Flush Tanks

1003-09

Performance Requirements for Water Pressure Reducing Valves .

1004-08

Performance Requirements for Backflow Prevention Requirements for Commercial Dishwashing Machines .

1005-99

Performance Requirements for Water Heater Drain Valves.

1006-86

Performance Requirements for Residential Use Dishwashers.

1007-86

Performance Requirements for Home Laundry Equipment

1008-06

Performance Requirements for Household Food Waste Disposer Units

1009-90

Performance Requirements for Commercial Food Waste Grinder Units

1010-04

Performance Requirements for Water Hammer Arresters

1011-04

Performance Requirements for Hose Connection Vacuum Breakers

1012-09

Performance Requirements for Backflow Preventers with Intermediate Atmospheric Vent .

1013-09

Performance Requirements for Reduced Pressure Principle Backflow Preventers and Reduced Pressure Fire Protection Principle Backflow Preventers

1015-09

Performance Requirements for Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

1016-05

Performance Requirements for Individual Thermostatic, Pressure Balancing and Combination Control Valves for Individual Fixture Fittings

1017-09

Performance Requirements for Temperature Actuated Mixing Valves for Hot Water Distribution Systems.

1018-01

Performance Requirements for Trap Seal Primer Valves; Potable Water Supplied

1019-04

Performance Requirements for Vacuum Breaker Wall Hydrants, Freeze Resistant, Automatic Draining Type

1020-04

Performance Requirements for Pressure Vacuum Breaker Assembly

1022-03

Performance Requirements for Backflow Preventer for Beverage Dispensing Equipment

1024-04

Performance Requirements for Dual Check Valve Type Backflow Preventers (for Residential Supply Service or Individual Outlets

1035-08

Performance Requirements for Laboratory Faucet Backflow Preventers

1037-90

Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures

1044-01

Performance Requirements for Trap Seal Primer Devices Drainage Types and Electronic Design Types

1047-09

Performance Requirements for Reduced Pressure Detector Fire Protection BackflowPrevention Assemblies

1048-09

Performance Requirements for Double Check Detector Fire Protection BackflowPrevention Assemblies

1050-09

Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems .

1051-09

Performance Requirements for Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems-fixture and Branch Devices

1052-04

Performance Requirements for Hose Connection Backflow Preventers

1055-09

Performance Requirements for Chemical Dispensing Systems

1056-01

Performance Requirements for Spill Resistant Vacuum Breaker

1060-06

Performance Requirements for Outdoor Enclosures for Backflow Prevention Assemblies

1061-06

Performance Requirements for Removable and Nonremovable Push Fit Fittings

1062-06

Performance Requirements for Temperature Actuated, Flow Reduction Valves to Individual Fixture Fittings

1066-97

Performance Requirements for Individual Pressure Balancing In-line Valves for Individual Fixture Fittings

1069-05

Performance Requirements for Automatic Temperature Control Mixing Valves

1070-04

Performance Requirements for Water-temperature Limiting Devices

1072-07

Performance Requirements for Barrier Type Floor Drain Trap Seal Protection Devices

1079-05

Dielectric Pipe Unions.

5013-09

Performance Requirements for Testing Reduced Pressure Principle Backflow Prevention Assembly (RPA) and Reduced Pressure Fire Protection PrincipleBackflow Preventers(RFP)

5015-09

Performance Requirements for Testing Double Check Valve Backflow Prevention Assembly (DCVA)

5020-09

Performance Requirements for Testing Pressure Vacuum Breaker Assembly (PVBA)

5047-09

Performance Requirements for Testing Reduced Pressure Detector Fire Protection BackflowPrevention Assemblies (RPDA) .

5048-09

Performance Requirements for Testing Double Check Valve Detector Assembly (DCDA).

5052-09

Performance Requirements for Testing Hose Connection Backflow Preventers

5056-09

Performance Requirements for Testing Spill Resistant Vacuum Breaker.

ASTMASTM International

100 Barr Harbor Drive

West Conshohocken, PA 19428-2959

Standard Referenced

Title

A 53/A 53M-10

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

A 74-09

Specification for Cast-iron Soil Pipe and Fittings

A 312/A 312M-09

Specification for Seamless and Welded Austenitic Stainless Steel Pipes

A 733-03 (2009)e1

Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples

A 778-01(2009)e1

Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products

A 888-09

Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Application

B 32-08

Specification for Solder Metal

B 42-10

Specification for Seamless Copper Pipe, Standard Sizes

B 43-09

Specification for Seamless Red Brass Pipe, Standard Sizes

B 75-02

Specification for Seamless Copper Tube

B 88-09

Specification for Seamless Copper Water Tube

B 152/B 152M-09

Specification for Copper Sheet, Strip Plate and Rolled Bar

B 251-10

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

B 302-07

Specification for Threadless Copper Pipe, Standard Sizes

B 306-09

Specification for Copper Drainage Tube (DWV)

B 447-07

Specification for Welded Copper Tube

B 687-99(2005)e01

Specification for Brass, Copper and Chromium-plated Pipe Nipples

B 813-10

Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube

B 828-02

Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings.

C 4-04 (2009)

Specification for Clay Drain Tile and Perforated Clay Drain Tile

C 14-07

Specification for Nonreinforced Concrete Sewer, Storm Drain and Culvert Pipe.

C 76-10a

Specification for Reinforced Concrete Culvert, Storm Drain and Sewer Pipe

C 296-00 (2009)e1

Specification for Asbestos-cement Pressure Pipe

C 425-04 (2009)

Specification for Compression Joints for Vitrified Clay Pipe and Fittings

C 428-05 (2006)

Specification for Asbestos-cement Nonpressure Sewer Pipe

C 443-05ae1

Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

C 508- 00 (2009)e1

Specification for Asbestos-cement Underdrain Pipe

C 564-09a

Specification for Rubber Gaskets for Cast-iron Soil Pipe and Fittings

C 700-09

Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated .

C 1053-00(2010)

Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications

C 1173-08

Specification for Flexible Transition Couplings for Underground Piping System.

C 1277-09a

Specification for Shielded Coupling Joining Hubless Cast-iron Soil Pipe and Fittings

C 1440-08

Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste,and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems

C 1460-08

Specification for Shielded Transition Couplings for Use with Dissimilar DWV Pipe and Fittings Above Ground

C 1461-08

Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste and Vent (DWV) Sewer, Sanitary and Storm Plumbing Systems for Above and Below Ground Use

C 1540-09a

Specification for Heavy Duty Shielded Couplings Joining Hubless Cast-iron Soil Pipe and Fittings

C 1563-08

Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent and Storm Piping Applications

D 1527-99(2005)

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80

D 1785-06

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80 and 120

D 1869-95(2005)e1

Specification for Rubber Rings for Asbestos-cement Pipe

D 2235-04

Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

D 2239-03

Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

D 2241-09

Specification for Poly (Vinyl Chloride) (PVC) Pressure-rated Pipe (SDR-Series)

D 2282-(2005)99e01

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (SDR-PR)

D 2464-06

Specification for Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2466-06

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40

D 2467-06

Specification for Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80

D 2468-96a

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40

D 2564-04 (2009) e01

Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems

D 2609-02 (2008)

Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe.

D 2657-07

Practice for Heat Fusion-joining of Polyolefin Pipe and Fitting

D 2661-08

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

D 2665-09

Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

D 2672-96a(2009)

Specification for Joints for IPS PVC Pipe Using Solvent Cement .

D 2683-10

Standard Specification for Socket-type Polyethylene fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

D 2729-03

Specification for Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

D 2737-03

Specification for Polyethylene (PE) Plastic Tubing

D 2751-05

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings

D 2846/D 2846M-09b

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot and Cold Water Distribution Systems

D 2855-96(2010)

Standard Practice for Making Solvent-cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings D 2949-01ae01 Specification for 3.25 -in Outside Diameter Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

D 3034-08

Specification for Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings

D 3035-08

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

D 3139-98(2005)

Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals

D 3212-07

Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

D 3261-10a

Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic fittings for Polyethylene (PE) Plastic Pipe and Tubing

D 3311-06a09a

Specification for Drain, Waste and Vent (DWV) Plastic Fittings Patterns

D 4068-09

Specification for Chlorinated Polyethlene (CPE) Sheeting for Concealed Water-containment Membrane

D 4551-96(2008) e1

Specification for Poly (Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-containment Membrane

F 405-05

Specification for Corrugated Polyethylene (PE) Tubing and Fittings

F 409-02(2008)

Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings .

F 437-09

Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 438-09

Specification for Socket-type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40

F 439-09

Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F 441/F 441M-09

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80

F 442/F 442M-09

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR)

F 477-10

Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

F 493-10

Specification for Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

F 628-08

Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core

F 656-10

Specification for Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings

F 714-08

Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter

F 876-10

Specification for Cross-linked Polyethylene (PEX) Tubing

F 877-07

Specification for Cross-linked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems

F 891-10

Specification for Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe with a Cellular Core .

F 1055-98(2006)

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing

F 1281-07

Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Pressure Pipe

F 1282-10

Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

F 1412-09

Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage

F 1488-09

Specification for Coextruded Composite Pipe

F 1673-10

PolyvinylideneFluoride (PVDF) Corrosive Waste Drainage Systems

F 1807-07

Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing

F 1866-07

Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings .

F 1960-10

Specification for Cold Expansion Fittings with PEX Reinforcing Rings for use with Cross-linked Polyethylene (PEX) Tubing.

F 1974-09

Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Composite Pressure Pipe

F 1986-01(2006)

Specification for Multilayer Pipe, Type 2, Compression Fittings and Compression Joints for Hot and Cold Drinking Water Systems.

F 2080-09

Specifications for Cold-expansion Fittings with Metal Compression-sleeves for Cross-linked Polyethylene (PEX) Pipe

F 2098-08

Standard specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing to Metal Insert Fittings

F 2159-10

Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing

F 2262-09

Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene Tubing OD Controlled SDR9

F 2306/F 2306M-08

12" to 60" Annular Corrugated Profile-wall Polyethylene (PE) Pipe and Fittings for Gravity Flow Storm Sewer and Subsurface Drainage Applications

F 2389-10

Specification for Pressure-rated Polypropylene (PP) Piping Systems

F 2434-09

Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEXAL-PEX) Tubing.

AWS American Welding Society

550 N.W. LeJeune Road

Miami, FL 33126

Standard Referenced

Title

A 5.8 -04

Specifications for Filler Metals for Brazing and Braze Welding

AWWAAmerican Water Works Association

6666 West Quincy Avenue

Denver, CO 80235

Standard Referenced

Title

C104/A 21.4-08

Standard for Cement-mortar Lining for Ductile-iron Pipe and Fittings for Water

C110/A 21.10 -08

Standard for Ductile-iron and Gray-iron Fittings, 3 Inches through 48 Inches, for Water

C111/A 21.11-06

Standard for Rubber-gasket Joints for Ductile-iron Pressure Pipe and Fittings

C115/A 21.15 -05

Standard for Flanged Ductile-iron Pipe with Ductile-iron or Gray-iron Threaded Flanges

C151/A 21.51 -09

Standard for Ductile-iron Pipe, Centrifugally Cast for Water

C153/A 21.53 -06

Standard for Ductile-iron Compact Fittings for Water Service

C510-07

Double Check Valve Backflow Prevention Assembly

C511-07

Reduced-pressure Principle Backflow Prevention Assembly

C651-05

Disinfecting Water Mains

C652-02

Disinfection of Water-storage Facilities

CISPICast Iron Soil Pipe Institute

5959 Shallowford Road, Suite 419

Chattanooga, TN 37421

Standard Referenced

Title

301-09

Specification for Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

310-09

Specification for Coupling for Use in Connection with Hubless Cast-iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste and Vent Piping Applications

CSACanadian Standards Association

5060 Spectrum Way.

Mississauga, Ontario, Canada L4W 5N6

Standard Referenced

Title

B 45.1 -02 (R2008)

Ceramic Plumbing Fixtures.

B 45.2 -02 (R2008)

Enameled Cast-iron Plumbing Fixtures

B 45.3 -02 (R2008)

Porcelain Enameled Steel Plumbing Fixtures

B 45.4 -02 (R2008)

Stainless-steel Plumbing Fixtures

B 45.5 -02 (R2008)

Plastic Plumbing Fixtures

B 45.9 -99 (R2008)

Macerating Systems and Related Components

B64.1.2-07

Vacuum Breakers, Pressure Type (PVB

B64.2.1-07

Vacuum Breakers, Hose Connection Type (HCVB) with Manual Draining Feature

B64.2.1.1-07

Vacuum Breakers, Hose Connection Dual Check Type (HCDVB)

B64.4.1-07

Backflow Preventers, Reduced Pressure Principle Type for Fire Sprinklers (RPF)

B 64.5 -07

Backflow Preventers, Double Check Type (DCVA)

B64.5.1-07

Backflow Preventers, Double Check Type for Fire Systems (DCVAF)

B 64.6 -07

Backflow Preventers, Dual Check Valve Type (DuC)

B 64.7 -07

Vacuum Breakers, Laboratory Faucet Type (LFVB

B 64.10 /B64.10.1-07

Manual for the Selection and Installation of Backflow Prevention Devices/Manual for the Maintenance and Field Testing of Backflow Prevention Devices

B79-08

Floor, Area and Shower Drains, and Cleanouts for Residential Construction

B125-01

Plumbing Fittings

B 125.3 -2005

Plumbing Fittings

B 137.1 -09

Polyethylene Pipe, Tubing and Fittings for Cold Water Pressure Services

B 137.2 -09

PVC Injection-moulded Gasketed Fittings for Pressure Applications

B 137.3 -09

Rigid Poly (Vinyl Chloride) (PVC) Pipe for Pressure Applications

B 137.5 -09

Cross-linked Polyethylene (PEX) Tubing Systems for Pressure Applications-with Revisions through September 1992

B 137.6 -09

CPVC Pipe, Tubing and Fittings for Hot and Cold Water Distribution Systems- with Revisions through May 1986B 137.11 -02 Polypropylene (PP-R) Pipe and Fittings for Pressure Applications

B 181.1 -06

ABS Drain, Waste and Vent Pipe and Pipe Fittings

B 181.2 -06

PVC Drain, Waste, and Vent Pipe and Pipe Fittings- with Revisions through December 1993

B 182.1 -06

Plastic Drain and Sewer Pipe and Pipe Fittings

B 182.2 -06

PVC Sewer Pipe and Fittings (PSM Type)

B 182.4 -06

Profile PVC Sewer Pipe and Fittings

B 182.6 -06

Profile Polyethylene Sewer Pipe and Fittings for Leak-proof Sewer Applications

B 182.8 -06

Profile Polyethylene Storm Sewer and Drainage Pipe and Fittings

CAN/CSA-A 257.1 M-09

Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

CAN/CSA-A 257.2 M-09

Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and Fittings

CAN/CSA-A 257.3 M-09

Joints for Circular Concrete Sewer and Culvert Pipe, Manhole Sections and Fittings Using Rubber Gaskets

CAN/CSA-B64.1.1-07

Vacuum Breakers, Atmospheric Type (AVB)

CAN/CSA-B 64.2 -07

Vacuum Breakers, Hose Connection Type (HCVB).

CAN/CSA-B64.2.2-07

Vacuum Breakers, Hose Connection Type (HCVB) with Automatic Draining Feature

CAN/CSA-B 64.3 -07

Backflow Preventers, Dual Check Valve Type with Atmospheric Port (DCAP)

CAN/CSA-B 64.4 -07

Backflow Preventers, Reduced Pressure Principle Type (RP)

CAN/CSA-B 64.10 -07

Manual for the Selection, Installation, Maintenance and Field Testing of Backflow Prevention Devices

CAN/CSA-B 137.9 -09

Polyethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems

CAN/CSA-B 137.10 M-09

Cross-linked Polyethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems

CAN/CSA-B 181.3 -06

Polyolefin Laboratory Drainage Systems

CAN/CSA-B 182.4 -06

Profile PVC Sewer Pipe and Fittings

CAN/CSA-B602-10

Mechanical Couplings for Drain, Waste and Vent Pipe and Sewer Pipe

ICC International Code Council, Inc.

500 New Jersey Ave, NW 6th Floor

Washington, DC 20001

Standard Referenced

Title

IFGC-09

International Fuel Gas Code (including ICC Emergency Amendment changing IFGC Sections 406.7 )

ISEA International Safety Equipment Association

1901 N. Moore Street, Suite 808

Arlington, VA 22209

Standard Referenced

Title

Z 358.1 -09

Emergency Eyewash and Shower Equipment

NFPANational Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

Standard Referenced

Title

70-11

National Electrical Code

99C-05

Gas and Vacuum Systems

NSFNSF International

789 Dixboro Road

Ann Arbor, MI 48105

Standard Referenced

Title

3-2009

Commercial Warewashing Equipment

14-2010

Plastic Piping System Components and Related Materials

18-2009

Manual Food and Beverage Dispensing Equipment

42-2009

Drinking Water Treatment Units-Aesthetic Effects

44-2009

Residential Cation Exchange Water Softeners

53-2009e

Drinking Water Treatment Units-Health Effects.

58-2009

Reverse Osmosis Drinking Water Treatment Systems

61-2010a

Drinking Water System Components-Health Effects

62-2009

Drinking Water Distillation Systems

PDIPlumbing and Drainage Institute

800 Turnpike Street, Suite 300

North Andover, MA 01845

Standard Referenced

Title

G101(2010)

Testing and Rating Procedure for Grease Interceptors with Appendix of Sizing and Installation Data

ULUnderwriters Laboratories, Inc.

333 Pfingsten Road

Northbrook, IL 60062-2096

Standard Referenced

Title

UL 508-99

Industrial Control Equipment with Revision through July 2005

Effective: 03/01/2013
R.C. 119.032 review dates: 11/01/2016
Promulgated Under: 119.03
Statutory Authority: 3781.10(A)
Rule Amplifies: 3781., 3791.
Prior Effective Dates: 3/1/98, 4/1/99, 12/1/00, 1/1/02, 1/1/04, 3/1/05, 9/6/05, 3/1/06, 7/1/07, 1/1/08, 3/31/08(Emer.), 6/24/08, 1/1/09, 11/1/11

4101:3-13-02 Referenced standards. [Rescinded].

Rescinded eff 7-1-07