Chapter 4101:8-44 Referenced Standards

4101:8-44-01 Referenced standards.

4401.1 General. This chapter lists the standards that are referenced in various sections of this code. The standards are listed herein by the promulgating agency of the standard, the standard identification, the effective date and title. The application of the referenced standards shall be as specified in Section 102.5.

4401.2 Referenced codes. When indicated in this code, the following codes refer to provisions in the listed chapters of the administrative code:

Referenced Code

Ohio Administrative Code Chapters

    

Ohio Building Code

4101:1-1 to 4101:1-35

Fire Code

1301:7-1 to 1301:7-7

Mechanical Code

4101:2-1 to 4101:2-15

Plumbing Code

4101:3-1 to 4101:3-13, codified and published as the 2011 Ohio Plumbing Code, effective 11-1-2011 (including update effective 03-01-2013), and as modified in Section 2501.1.1.

4401.3 Referenced standard list.

American Architectural Manufacturers Association

1827 Walden Office Square, Suite 550

Schaumburg, IL 60173

AAMA Standard reference number

Title

AAMA/WDMA/CSA 101/I.S.2/A440-08

North American Fenestration Standard/Specification for Windows, Doors, and Skylights

450-10

Voluntary Performance Rating Method for Mulled Fenestration Assemblies

506-08

Voluntary Specifications for Hurricane Impact and Cycle Testing of Fenestration Products

711-07

Voluntary Specification for Self Adhering Flashing Used for Installation of Exterior Wall Fenestration Products.

Air Conditioning Contractors of America

2800 Shirlington Road, Suite 300

Arlington, VA 22206

ACCA Standard reference number

Title

Manual D-09

Residential Duct Systems

Manual J- 04

Residential Load Calculation-Eighth Edition

Manual S-04

Residential Equipment Selection

American Concrete Institute

38800 Country Club Drive

Farmington Hills, MI 48331

ACE Standard reference number

Title

318-08

Building Code Requirements for Structural Concrete

332- 08

Code Requirements for Residential Concrete Construction

530-08

Building Code Requirements for Masonry Structures

530.1 -08

Specification for Masonry Structures

American Forest and Paper Association

1111 19th Street, NW, Suite 800

Washington, DC 20036

American Forest Products Association (Currently the American Wood Council)

803 Sycolin Road, Suite 201

Leesburg, VA 20175

http://www.awc.org/index.html

AFPA Standard reference number

Title

NDS- 05

National Design Specification (NDS) for Wood Construction-with 2005 Supplement

WFCM- 01

Wood Frame Construction Manual for One- and Twofamily Dwellings

AFPA-93

Span Tables for Joists and Rafters

PWF-07

Permanent Wood Foundation Design Specification

American Iron and Steel Institute

1140 Connecticut Ave, Suite 705

Washington, DC 20036

AITC Standard reference number

Title

AISI S100-07

North American Specification for the Design of Cold-formed Steel Structural Members

AISI S230-07

Standard for Cold-formed Steel Framingprescriptive Method for One- and Two-family Dwellings

American Institute of Timber Construction

7012 S. Revere Parkway, Suite 140

Centennial, CO 80112

AITC Standard reference number

Title

ANSI/AITC A 190.1 -07

Structural Glued Laminated Timber

American National Standards Institute

25 West 43rd Street, Fourth Floor

New York, NY 10036

AITC Standard reference number

Title

A 108.1 A-09

Installation of Ceramic Tile in the Wet-set Method, with Portland Cement Mortar

A 108.1 B-09

Installation of Ceramic Tile, Quarry Tile on a Cured Portland Cement Mortar Setting Bed with Dry-set or Latex-Portland Mortar

A 108.4 -09

Installation of Ceramic Tile with Organic Adhesives or Water Cleanable Tile-setting Epoxy Adhesive

A 108.5 -09

Installation of Ceramic Tile with Dry-set Portland Cement Mortar or Latex-Portland Cement Mortar

A 108.6 -09

Installation of Ceramic Tile with Chemical-resistant, Water-cleanable Tile-setting and -grouting Epoxy

A 108.11 -09

Interior Installation of Cementitious Backer Units

A 118.1 - 10.1

American National Standard Specifications for Dry-set Portland Cement Mortar

A 118.3 - 10.1

American National Standard Specifications for Chemical-resistant, Water-cleanable Tile-setting and Grouting Epoxy and Water-cleanable Tile-setting Epoxy Adhesive

A 118.10 - 10.1

Specification for Load Bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone Installation

A 136.1 - 10.1

American National Standard Specifications for Organic Adhesives for Installation of Ceramic Tile

A 137.1 -08

American National Standard Specifications for Ceramic Tile

A 208.1 -09

Particleboard

LC1-05

Interior Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing

LC4-07

Press-connect Copper and Copper Alloy Fittings for use in Fuel Gas Distribution Systems

Z 21.1 -05

Household Cooking Gas Appliances

Z21.5.1-06

Gas Clothes Dryers-Volume I-Type I Clothes Dryers

Z 21.8 -94 (R2002)

Installation of Domestic Gas Conversion Burners

Z21.10.1-09

Gas Water Heaters-Volume I-Storage Water Heaters with Input Ratings of 75,000 Btu per hour or Less

Z21.10.3-07

Gas Water Heaters-Volume III-Storage Water Heaters with Input Ratings above 75,000 Btu per hour, Circulating and Instantaneous Water Heaters

Z21.11.2-07

Gas-fired Room Heaters-Volume II-Unvented Room Heaters

Z 21.13 -10

Gas-fired Low-Pressure Steam and Hot Water Boilers

Z 21.15 - 09

Manually Operated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves

Z 21.24 - 06

Connectors for Gas Appliances

Z21.40.1-96 (R2002)

Gas-fired, Heat-activated Air Conditioning and Heat Pump Appliances- with Z21.40.1a-97 (R2002)

Z21.40.2-96 (R2002)

Gas-fired, Work-activated Air Conditioning and Heat Pump Appliances (Internal Combustion) - with Z21.40.2a-1997 (R2002)

Z 21.42 -04

Gas-fired Illuminating Appliances

Z 21.47 -06

Gas-fired Central Furnaces

Z 21.50 -07

Vented Gas Fireplaces

Z 21.56 -06

Gas-fired Pool Heaters

Z 21.58 -08

Outdoor Cooking Gas Appliances

Z 21.60 -03

Decorative Gas Appliances for Installation in Solid Fuel Burning Fireplaces-with Addenda Z 21.60 a-2003

Z 21.75 /CSA 6.27 -07

Connectors for Outdoor Gas Appliances

Z 21.80 -03

Line Pressure Regulators

Z 21.83 -98

Fuel Cell Power Plants.

Z 21.84 -02

Manually Listed, Natural Gas Decorative Gas Appliances for Installation in Solid Fuel-burning Fireplaces-with Addenda Z 21.84 a -2003

Z 21.86 -08

Gas-fired Vented Space Heating Appliances

Z 21.88 -09

Vented Gas Fireplace Heaters

Z 21.91 -07

Ventless Firebox Enclosures for Gas-fired Unvented Decorative Room Heaters

Z 83.6 -90 (R1998)

Gas-fired Infrared Heaters

Z 83.8 -09

Gas-fired Unit Heaters and Gas-fired Duct Furnaces

Z 97.1 -09

Safety Glazing Materials Used in Buildings-Safety Performance Specifications and Methods of Test

APA-The Engineered Wood Association

7011 South 19th

Tacoma, WA 98466

AITC Standard reference number

Title

APA E30-07 Engineered Wood Construction Guide

American Society of Civil Engineers Structural Engineering Institute

1801 Alexander Bell Drive

Reston, VA 20191

AITC Standard reference number

Title

5-08

Building Code Requirements for Masonry Structures

6-08

Specification for Masonry Structures

7-05

Minimum Design Loads for Buildings and Other Structures

24-05

Flood-resistant Design and Construction.

32-01

Design and Construction of Frost-protected Shallow Foundations

American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.

1791 Tullie Circle, NE

Atlanta, GA 30329

AITC Standard reference number

Title

34-10

Designation and Safety Classification of Refrigerants

ASHRAE-09

ASHRAE Fundamentals Handbook-2009

American Society of Mechanical Engineers

Three Park Avenue

New York, NY 10016-5990

AITC Standard reference number

Title

A 17.1 /CSA B44- 2010

Safety Code for Elevators and Escalators

A 18.1 - 2008

Safety Standard for Platforms and Stairway Chair Lifts

B1.20.1-1983 (R2006)

Pipe Threads, General Purpose (Inch)

B 16.33 -2002 (R2007)

Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig (Sizes ½ through 2)

B 16.44 -02

Manually Operated Metallic Gas Valves For Use in Above-ground Piping Systems up to 5 psi.

B 36.10 M-2004

Welded and Seamless Wrought-steel Pipe

BPVC- 2010

ASME Boiler and Pressure Vessel Code

CSD-1-09

Controls and Safety Devices for Automatically Fired Boilers

American Society of Sanitary Engineering

901 Canterbury, Suite A

Westlake, OH 44145

ASTM International

100 Barr Harbor Drive

West Conshohocken, PA 19428

AITC Standard reference number

Title

A 36/A 36M-08

Specification for Carbon Structural Steel

A 53/A 53M-10a

Specification for Pipe, Steel, Black and Hot-dipped, Zinc-coated Welded and Seamless

A 82/A 82M-07

Specification for Steel Wire, Plain, for Concrete Reinforcement

A 106/A 106M-10

Specification for Seamless Carbon Steel Pipe for High Temperature Service

A 153/A 153M-09

Specification for Zinc Coating (Hot Dip) on Iron and Steel Hardware

A 167-09

Specification for Stainless and Heat-resisting Chromium-nickel Steel Plate, Sheet and Strip

A 240/A 240M-10a

Standard Specification for Chromium and Chromium-nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications

A 254-9707

Specification for Copper Brazed Steel Tubing

A 307-07b

Specification for Carbon Steel Bolts and Studs, 6000 psi Tensile Strength

A 463/A 463M-09a

Standard Specification for Steel Sheet, Aluminum-coated by the Hot-dip Process.

A 510-08

Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel

A 539-99

Specification for Electric-resistance-welded Coiled Steel Tubing for Gas and Fuel Oil Lines

A 615/A 615M-09b

Specification for Deformed and Plain Billet-steel Bars for Concrete Reinforcement

A 641/A 641M-09b

Specification for Zinc-coated (Galvanized) Carbon Steel Wire

A 653/A 653M-09a

Specification for Steel Sheet, Zinc-coated (Galvanized) or Zinc-iron Alloy-coated (Galvanized) by the Hot-dip Process

A 706/A 706/M-09b

Specification for Low-alloy Steel Deformed and Plain Bars for Concrete Reinforcement

A 755/A 755M-03 (2008)

Specification for Steel Sheet, Metallic Coated by the Hot-dip Process and Prepainted by the Coil-coating Process for Exterior Exposed Building Products

A 778-01 (2009)e1

Specification for Welded Unannealed Austenitic Stainless Steel Tubular Products

A 792/A 792M-09a

Specification for Steel Sheet, 55% Aluminum-zinc Alloy-coated by the Hot-dip Process

A 875/A 875M-09a

Specification for Steel Sheet, Zinc-5%, Aluminum Alloy-coated by the Hot-dip Process

A 924/A 924M-10

Standard Specification for General Requirements for Steel Sheet, Metallic-coated by the Hot-Dip Process

A 951-06

Specification for Steel Wire Masonry Joint Reinforcement

A 996/A 996M-09b

Specifications for Rail-steel and Axel-steel Deformed Bars for Concrete Reinforcement

A 1003/A 1003M-10

Standard Specification for Steel Sheet, Carbon, Metallic and Nonmetallic-coated for Cold-formed Framing Members

B 42-10

Specification for Seamless Copper Pipe, Standard Sizes

B 43-09

Specification for Seamless Red Brass Pipe, Standard Sizes

B 75-02

Specification for Seamless Copper Tube

B 88-09

Specification for Seamless Copper Water Tube

B 101-07

Specification for Lead-coated Copper Sheet and Strip for Building Construction.

B 135-10

Specification for Seamless Brass Tube

B 209-07

Specification for Aluminum and Aluminum-alloy Sheet and Plate

B 227-10

Specification for Hard-drawn Copper-clad Steel Wire

B 251-10

Specification for General Requirements for Wrought Seamless Copper and Copper-alloy Tube

B 302-07

Specification for Threadless Copper Pipe, Standard Sizes

B 306-09

Specification for Copper Drainage Tube (DWV)

B 370-09

Specification for Copper Sheet and Strip for Building Construction

B 447-07

Specification for Welded Copper Tube

B 695-04 (2009)

Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

B 813-10

Specification for Liquid and Paste Fluxes for Soldering Applications of Copper and Copper Alloy Tube

C 5-10

Specification for Quicklime for Structural Purposes

C 27-98 (2008)

Specification for Standard Classification of Fireclay and High-alumina Refractory Brick

C 28/C 28M-10

Specification for Gypsum Plasters

C 33-08

Specification for Concrete Aggregates

C 34-08

Specification for Structural Clay Load-bearing Wall Tile C 35-01(2005) Specification for Inorganic Aggregates for Use in Gypsum Plaster

C 36/C 36M-03

Specification for Gypsum Wallboard

C 37/C 37M-01

Specification for Gypsum Lath

C 55-09

Specification for Concrete Building Brick

C 59/C 59M-00 (2006)

Specification for Gypsum Casting and Molding Plaster

C 61/C 61M-00 (2006)

Specification for Gypsum Keene's Cement

C 62-10

Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)

C 73-05

Specification for Calcium Silicate Face Brick (Sand Lime Brick)

C 79-04a

Specification for Treated Core and Nontreated Core Gypsum Sheathing Board

C 90-09

Specification for Load-bearing Concrete Masonry Units

C 91-05

Specification for Masonry Cement

C 94/C 94M-10

Specification for Ready-mixed Concrete

C 129-06

Specification for Nonload-bearing Concrete Masonry Units

C 143/C 143M-10a

Test Method for Slump or Hydraulic Cement Concrete

C 145-85

Specification for Solid Load-bearing Concrete Masonry Units

C 150-09

Specification for Portland Cement

C 199-84 (2005)

Test Method for Pier Test for Refractory Mortar

C 203-05a

Standard Test Methods for Breaking Load and Flexural Properties of Block-type Thermal Insulation

C 207-06

Specification for Hydrated Lime for Masonry Purposes

C 208-08a

Specification for Cellulosic Fiber Insulating Board

C 216-10

Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

C 270-10

Specification for Mortar for Unit Masonry

C 272-01 (2007)

Standard Test Method for Water Absorption of Core Materials for Structural Sandwich Constructions

C 273-07a

Standard Test Method for Shear Properties of Sandwich Core Materials

C 315-07

Specification for Clay Flue Liners and Chimney Pots

C 406-10

Specifications for Roofing Slate

C 411-05

Test Method for Hot-surface Performance of High-temperature Thermal Insulation

C 475/C 475-02(2007)

Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard

C 476-10

Specification for Grout for Masonry

C 514-04 (2009)e1

Specification for Nails for the Application of Gypsum Wallboard

C 552-07

Standard Specification for Cellular Glass Thermal Insulation

C 557-03 (2009)e1

Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing

C 578-10

Specification for Rigid, Cellular Polystyrene Thermal Insulation

C 587-04 (2009)

Specification for Gypsum Veneer Plaster

C 588/C 588M-03e1

Specification for Gypsum Base for Veneer Plasters

C 595-10

Specification for Blended Hydraulic Cements

C 630/C 630M-03

Specification for Water-resistant Gypsum Backing Board

C 631-09

Specification for Bonding Compounds for Interior Gypsum Plastering

C 645-09a

Specification for Nonstructural Steel Framing Members

C 652-10

Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)

C 685-10

Specification for Concrete Made by Volumetric Batching and Continuous Mixing

C 728-05 (2010)

Standard Specification for Perlite Thermal Insulation Board

C 836/C836M-10

Specification for High Solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

C 843-99 (2006)

Specification for Application of Gypsum Veneer Plaster

C 844-10

Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster

C 847-10a

Specification for Metal Lath

C 887-05 (2010)

Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar

C 897-05 (2009)

Specification for Aggregate for Job-mixed Portland Cement-based Plasters

C 920-10

Standard Specification for Elastomeric Joint Sealants

C 926-06

Specification for Application of Portland Cement-based Plaster

C 931/C 931M-04

Specification for Exterior Gypsum Soffit Board

C 933-09

Specification for Welded Wire Lath

C 954-10

Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. ( 0.84 mm) to 0.112 in. ( 2.84 mm) in Thickness

C 955-09a

Specification for Load-bearing (Transverse and Axial) Steel Studs, Runners (Tracks), and Bracing or Bridging for Screw Application of Gypsum Panel Products and Metal Plaster Bases

C 957-10

Specification for High-solids Content, Cold Liquid-applied Elastomeric Waterproofing Membrane for Use with Integral Wearing Surface

C 960-04

Specification for Predecorated Gypsum Board

C 1002-07

Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases

C 1029-10

Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation

C 1032-06

Specification for Woven Wire Plaster Base

C 1047-10a

Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base

C 1063-08

Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-based Plaster.

C 1107-08

Standard Specification for Packaged Dry, Hydraulic-cement Grout (Nonshrink)

C 1116-10

Standard Specification for Fiber-reinforced Concrete and Shotcrete

C 1167-03 (2009)

Specification for Clay Roof Tiles

C 1177/C 1177M-08

Specification for Glass Mat Gypsum Substrate for Use as Sheathing

C 1178/C 1178M-08

Specification for Glass Mat Water-resistant Gypsum Backing Panel

C 1186-08

Specification for Flat Nonasbestos Fiber Cement Sheets

C 1261-10

Specification for Firebox Brick for Residential Fireplaces

C 1278/C 1278M-07a

Specification for Fiber-reinforced Gypsum Panels

C 1283-07a

Practice for Installing Clay Flue Lining

C 1288-99(2010)

Standard Specification for Discrete Nonasbestos Fiber-cement Interior Substrate Sheets

C 1289-10

Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

C 1325-08b

Standard Specification for Nonasbestos Fiber-mat Reinforced Cement Interior Substrate Sheets.

C 1328-05

Specification for Plastic (Stucco) Cement.

C 1395/C 1395M-06a

Specification for Gypsum Ceiling Board

C 1396/C 1396M-09a

Specification for Gypsum Board.

C 1492-03(2009)

Specification for Concrete Roof Tile

C 1513-10

Standard Specification for Steel Tapping Screws for Cold-formed Steel Framing Connections

C 1658/C 1658M-06

Standard Specification for Glass Mat Gypsum Panels

D 41-05 (2010)

Specification for Asphalt Primer Used in Roofing, Dampproofing and Waterproofing

D 43-00(2006)

Specification for Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing

D 225-07

Specification for Asphalt Shingles (Organic Felt)Surfaced with Mineral Granules

D 226/D 226M-09

Specification for Asphalt-saturated (Organic Felt)Used in Roofing and Waterproofing

D 227-03

Specification for Coal Tar Saturated (Organic Felt) Used in Roofing and Waterproofing

D 312-00(2006)

Specification for Asphalt Used in Roofing.

D 422-63 (2007)

Test Method for Particle-size Analysis of Soils

D 449-03 (2008)

Specification for Asphalt Used in Dampproofing and Waterproofing.

D 450-07

Specification for Coal-tar Pitch Used in Roofing, Dampproofing and Waterproofing

D 1227-95(2007)

Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

D 1248-05

Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

D 1622-08

Standard Test Method for Apparent Density of Rigid Cellular Plastics

D 1623-09

Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics

D 1693-08

Test Method for Environmental Stress-cracking of Ethylene Plastics

D 1784-08

Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds

D 1863-05

Specification for Mineral Aggregate Used in Built-up Roofs

D 1970-09

Specification for Self-adhering Polymer Modified Bitumen Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection

D 2126-09

Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging

D 2178-04

Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

D 2412-10

Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-plate Loading

D 2447-03

Specification for Polyethylene (PE) Plastic Pipe Schedules 40 and 80, Based on Outside Diameter

D 2513-09a

Specification for Thermoplastic Gas Pressure Pipe, Tubing and Fittings

D 2559-10a

Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (West Use) Exposure Conditions

D 2626-04

Specification for Asphalt-saturated and Coated Organic Felt Base Sheet Used in Roofing

D 2683-10

Specification for Socket-type Polyethylene Fittings for Outside Diameter-controlled Polyethylene Pipe and Tubing

D 2822-05

Specification for Asphalt Roof Cement

D 2823-05

Specification for Asphalt Roof Coatings

D 2824-06

Specification for Aluminum-pigmented Asphalt Roof Coatings, Nonfibered, Asbestos Fibered and Fibered without Asbestos

D 2837-08

Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

D 2846/D 2846M-09b

Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold-water Distribution Systems

D 2898-10

Test Methods for Accelerated Weathering of Fire-retardant-treated Wood for Fire Testing

D 3019-08

Specification for Lap Cement Used with Asphalt Roll Roofing, Nonfibered, Asbestos Fibered and Nonasbestos Fibered.

D 3035-08

Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based On Controlled Outside Diameter

D 3161-09

Test Method for Wind Resistance of Asphalt Shingles (Fan Induced Method)

D 3201-08ae1

Test Method for Hygroscopic Properties of Fire-retardant Wood and Wood-base Products

D 3309-96a (2002)

Specification for Polybutylene (PB) Plastic Hot-and Code-water Distribution System

D 3350-10

Specification for Polyethylene Plastic Pipe and Fitting Materials

D 3462/D 3462M-10a

Specification for Asphalt Shingles Made From Glass Felt and Surfaced with Mineral Granules.

D 3468-99 (2006)e01

Specification for Liquid-applied Neoprene and Chlorosulfanated Polyethylene Used in Roofing and Waterproofing

D 3679-09a

Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding

D 3737-09

Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

D 3747-79 (2007)

Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation

D 3909-97b (2004)e01

Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules

D 3957-09

Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings

D 4022-07

Specification for Coal Tar Roof Cement, Asbestos Containing

D 4318-10

Test Methods for Liquid Limit, Plastic Limit and Plasticity Index of Soils

D 4434/D 4434-09

Specification for Poly (Vinyl Chloride) Sheet Roofing

D 4479-07

Specification for Asphalt Roof Coatings-asbestos-free

D 4586-07

Specification for Asphalt Roof Cement-asbestos-free

D 4601-04

Specification for Asphalt-coated Glass Fiber Base Sheet Used in Roofing

D 4637/D 4637M-10

Specification for EPDM Sheet Used in Single-ply Roof Membrane

D 4829-08a

Test Method for Expansion Index of Soils

D 4869-05e01

Specification for Asphalt-saturated (Organic Felt) Underlayment Used in Steep Slope Roofing

D 4897/D 4897M-01(2009)

Specification for Asphalt Coated Glass-fiber Venting Base Sheet Used in Roofing

D 4990-97a (2005)e01

Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing

D 5019-07a

Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane

D 5055-10

Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-joists

D 5516-09

Test Method for Evaluating the Flexural Properties of Fire-retardant-treated Softwood Plywood Exposed to the Elevated Temperatures

D 5643-06

Specification for Coal Tar Roof Cement Asbestos-free

D 5664-10

Test Methods For Evaluating the Effects of Fire-retardant Treatments and Elevated Temperatures on Strength Properties of Fire-retardant-treated Lumber

D 5665-99a(2006)

Specification for Thermoplastic Fabrics Used in Cold-applied Roofing and Waterproofing

D 5726-98(2005)

Specification for Thermoplastic Fabrics Used in Hot-applied Roofing and Waterproofing

D 6083-05e01

Specification for Liquid-applied Acrylic Coating Used in Roofing

D 6162-08

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

D 6163-00 (2008)

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

D 6164-05e1

Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements

D 6222-08

Specification for Atactic Polypropelene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcement.

D 6223/D 6223M-02(2009)e01

Specification for Atactic Polypropelene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcement

D 6298-05 e1

Specification for Fiberglass-reinforced Styrene Butadiene Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface

D 6305-08

Practice for Calculating Bending Strength Design Adjustment Factors for Fire-retardant-treated Plywood Roof Sheathing

D 6380-03(2008)

Standard Specification for Asphalt Roll Roofing (Organic Felt)

D 6694-08

Standard Specification Liquid-applied Silicone Coating Used in Spray Polurethane Foam Roofing

D 6754/D 6754M-10

Standard Specification for Ketone-ethylene-ester-based Sheet Roofing2

D 6757-07

Standard Specification for Inorganic Underlayment for Use with Steep Slope Roofing Products.

D 6841-08

Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-retardant-treated Lumber

D 6878-08e1

Standard Specification for Thermoplastic-polyolefin-based Sheet Roofing.

D 6947-07

Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System

D 7032-10a

Standard Specification for Establishing Perfomance Ratings for Wood-plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails).

D 7158-08d

Standard Test Method for Wind Resistance of Sealed Asphalt Shingles (Uplift Force/ Uplift Resistance Method

E 84-10b

Test Method for Surface Burning Characteristics of Building Materials

E 90-04

Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements

E 96/E 96M-05

Test Method for Water Vapor Transmission of Materials

E 108-10a

Test Methods for Fire Tests of Roof Coverings

E 119-10b

Test Methods for Fire Tests of Building Construction and Materials

E 136-09b

Test Method for Behavior of Materials in a Vertical Tube Furnace at 750°C

E 283-04

Test Method for Determining the Rate of Air Leakage through Exterior Windows, Curtain Walls and Doors Under Specified Pressure Differences Across the Specimen

E 330-02 (2010)

Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference

E 331-00 (2009)

Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform Static Air Pressure Difference

E 492-09

Specification for Laboratory Measurement of Impact Sound Transmission through Floor-ceiling Assemblies Using the Tapping Machine

E 814-10

Test Method for Fire Tests of Through-penetrationFirestops

E 970-10

Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source

E 1509-04

Standard Specification for Room Heaters, Pellet Fuel-burning Type

E 1602-03(2010)e1

Guide for Construction of Solid Fuel Burning Masonry Heaters

E 1886-05

Test Method for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Missles and Exposed to Cyclic Pressure Differentials

E 1996-09

Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

E 2178-03

Standard Test Method for Air Permeance of Building Materials

E 2231-09

Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics

E 2273-03

Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies

E 2568-09e1

Standard Specification for PB Exterior Insulation and Finish Systems (EIFS)

E 2570-07

Standard Test Methods for Evaluating Water-resistive Barrier (WRB) Coatings Used Under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage

F 876-10

Specification for Cross-linked Polyethylene (PEX) Tubing

F 877-07

Specification for Cross-linked Polyethylene (PEX) Plastic Hot-and Cold-water Distribution Systems

F 1055-98(2006)

Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Fittings

F 1281-07

Specification for Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Pressure Pipe

F 1282-10

Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe

F 1554-07a

Specification for Anchor Bolts, Steel, 36, 55 and 105-ksi Yield Strength

F 1667-10

Specification for Driven Fasteners, Nails, Spikes and Staples

F 1807-10e1

Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing

F 1960-10

Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing

F 1973-08

Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA 11) Fuel Gas Distribution Systems

F 2090-10

Specification for Window Fall Prevention Devices-with Emergency Escape (Egress) Release Mechanisms

F 2098-08

Standard Specification for Stainless Steel Clamps for SDR9 PEX Tubing to Metal Insert Fittings

F 2389-10

Standard for Pressure-rated Polypropylene (PP) Piping Systems

F 2623-08

Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDRG Tubing

American Wood Protection Association

P.O. Box 361784

Birmingham, AL 35236-1784

AWPA Standard reference number

Title

C1-03

All Timber Products-Preservative Treatment by Pressure Processes

M4-06

Standard for the Care of Preservative-treated Wood Products

U1-10

USE CATEGORY SYSTEM: User Specification for Treated Wood Except Section 6 Commodity Specification H

Canadian General Standards Board

Place du Portage 111, 6B1 11 Laurier Street

Gatineau, Quebec, Canada KIA 1G6

CGSB Standard reference number

Title

37-GP-52M-(1984)

Roofing and Waterproofing Membrane, Sheet Applied, Elastomeric

37-GP-56M-(1985)

Membrane, Modified Bituminous, Prefabricated and Reinforced for Roofing-with December 1985 Amendment

CAN/CGSB- 37.54 -95

Polyvinyl Chloride Roofing and Waterproofing Membrane

Composite Panel Association

19465 Deerfield Avenue, Suite 306

Leesburg, VA 20176

CPA Standard reference number

Title

ANSI A 135.4 -04

Basic Hardboard

ANSI A 135.5 -04

Prefinished Hardboard Paneling

ANSI A 135.6 -06

Hardboard Siding

Consumer Product Safety Commission

4330 East West Highway

Bethesda, MD 20814-4408

CPSC Standard reference number

Title

16 CFR Part 1201 -(1977)

Safety Standard for Architectural Glazing

16 CFR Part 1209 -(1979)

Interim Safety Standard for Cellulose Insulation

16 CFR Part 1404 -(1979)

Cellulose Insulation

Canadian Standards Association

5060 Spectrum Way

Mississauga, Ontario, Canada L4N 5N6

CSA Standard reference number

Title

CSA Requirement 3-88

Manually Operated Gas Valves for Use in House Piping Systems

CSA 8-93

Requirements for Gas Fired Log Lighters for Wood Burning Fireplaces-with Revisions through January 1999

O325-07

Construction Sheathing

O437-Series-93

Standards on OSB and Waferboard (Reaffirmed 2006)

101/I.S.2/A440-08

Specifications for Windows, Doors and Unit Skylights

CAN/CSA B 137.10 M-09

Cross-linked Polyethylene/Aluminum/Polyethylene Composite Pressure Pipe Systems

Cedar Shake & Shingle Bureau P. O. Box 1178

Sumas, WA 98295-1178

CSSB Standard reference number

Title

CSSB-97

Grading and Packing Rules for Western Red Cedar Shakes and Western Red Shingles of the Cedar Shake and Shingle Bureau

Door and Access Systems Manufacturers Association International

1300 Summer Avenue

Cleveland, OH 44115-2851

DASMA Standard reference number

Title

108-05

Standard Method for Testing Garage Doors: Determination of Structural Performance Under Uniform Static Air Pressure Difference

United States Department of Commerce

1401 Constitution Avenue, NW

Washington, DC 20230

DOC Standard reference number

Title

PS 1-07

Structural Plywood

PS 2-04

Performance Standard for Wood-based Structural-use Panels

R803.2.1/ PS 20-05

American Softwood Lumber Standard

Department of Transportation

1200 New Jersey Avenue SE East Building, 2nd floor

Washington, DC 20590

DOTn Standard reference number

Title

49 CFR, Parts 192.281(e) & 192.283(b)

Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards

Federal Emergency Management Agency

500 C Street, SW

Washington, DC 20472

FEMA Standard reference number

Title

TB-2-08

Flood Damage-Resistant Materials Requirements

FIA-TB-11-01

Crawlspace Construction for Buildings Located in Special Flood Hazard Area

Factory Mutual Global Research Standards Laboratories

Department 1301 Atwood Avenue, P. O. Box 7500

Johnson, RI 02919

FM Standard reference number

Title

4450-(1989)

Approval Standard for Class 1 Insulated Steel Deck Roofs-with Supplements through July 1992

4880-(2010)

American National Standard for Evaluating Insulated Wall or Wall and Roof/Ceiling Assemblies, Plastic Interior Finish Materials, Plastic Exterior Building Panels, Wall/Ceiling Coating Systems, Interior or Exterior Finish Systems

Gypsum Association

810 First Street, Northeast, Suite 510

Washington, DC 20002-4268

GA Standard reference number

Title

GA-253-07

Application of Gypsum Sheathing

Hardwood Plywood & Veneer Association

1825 Michael Faraday Drive

Reston, Virginia 20190-5350

HPVA Standard reference number

Title

HP-1-2009

The American National Standard for Hardwood and Decorative Plywood

International Code Council, Inc.

500 New Jersey Avenue, NW 6th Floor

Washington, DC 20001

ICC Standard reference number

Title

ICC/ANSI A 117.1 - 09

Accessible and Usable Buildings and Facilities

ICC 400 - 07

Standard on the Design and Construction of Log Structures

ICC 500 - 08

ICC/NSSA Standard on the Design and Construction of Storm Shelters

ICC 600 - 08

Standard for Residential Construction in High Wind Regions

IEBC-09

International Existing Buildings Code

IECC - 09

International Energy Conservation Code (adoption includes only section 101 of chapter 1 and chapters 2 through 6)

IFGC - 09

International Fuel Gas Code (including ICC Emergency Amendment changing section 406.7 )

International Organization for Standardization

1, ch. de la Voie -Creuse Case postale 56 CH-1211

Geneva 20, Switzerland

ISO Standard reference number

Title

15874-03

Polypropylene Plastic Piping Systems for Hot and Cold Water Installations

Manufacturers Standardization Society of the Valve and Fittings Industry

127 Park Street, Northeast

Vienna, VA 22180

MSS Standard reference number

Title

SP-58-09

Pipe Hangers and Supports-Materials, Design and Manufacture

North American Insulation Manufacturers Association

44 Canal Center Plaza, Suite 310

Alexandria, VA 22314

NAIMA Standard reference number

Title

AH 116-02

Fibrous Glass Duct Construction Standards, Fifth Edition

National Concrete Masonry Association

13750 Sunrise Valley Drive

Herndon, VA 20171-4662

NCMA Standard reference number

Title

TR 68-A-75

Design and Construction of Plain and Reinforced Concrete Masonry and Basement and Foundation Walls

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02269

NFPA Standard reference number

Title

13-10

Installation of Sprinkler Systems (including TIA 10-2)

13D-10

Standard for the Installation of Sprinkler Systems in One-and Two-family Dwellings and Manufactured Homes (including TIA 10-2)

13R-10

Standard for the Installation of Sprinkler Systems in Residential Occupancies up to and Including Four Stories in Height (including TIA 10-2)

31-06

Installation of Oil-burning Equipment

58-11

Liquefied Petroleum Gas Code

70-11

National Electrical Code

72-10

National Fire Alarm and Signaling Code

85-07

Boiler and Construction Systems Hazards Code

211-10

Chimneys, Fireplaces, Vents and Solid Fuel Burning Appliances

259-08

Test Method for Potential Heat of Building Materials

286-06

Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth

501-05

Standard on Manufactured Housing

853-10

Standard for the Installation of Stationary Fuel Cell Power Systems

National Fenestration Rating Council Inc.

8484 Georgia Avenue, Suite 320

Silver Spring, MD 20910

NFRC Standard reference number

Title

100-10

Procedure for Determining Fenestration Product U-factors

200-10

Procedure for Determining Fenestration Product Solar Heat Gain Coefficients and Visible Transmittance at Normal Incidence

400-10

Procedure for Determining Fenestration Product Air Leakage

Portland Cement Association

5420 Old Orchard Road

Skokie, IL 60077

PCA Standard reference number

Title

100-07

Prescriptive Design of Exterior Concrete Walls for One-and Two-family Dwellings (Pub. No. EB241)

Sheet Metal & Air Conditioning Contractors National Assoc. Inc.

4021 Lafayette Center Road

Chantilly, VA 22021

SMACNA Standard reference number

Title

SMACNA-03

Fibrous Glass Duct Construction Standards (2003)

The Masonry Society

3970 Broadway, Suite 201-D

Boulder, CO 80304

TMS Standard reference number

Title

302-07

Standard Method for Determining the Sound Transmission Class Rating for Masonry Walls

402-08

Building Code Requirements for Masonry Structures

602-08

Specification for Masonry Structures

Truss Plate Institute

583 D'Onofrio Drive, Suite 200

Madison, WI 53719

TPI Standard reference number

Title

TPI 1-2007

National Design Standard for Metal-plate-connected Wood Truss Construction

Underwriters Laboratories, Inc.

333 Pfingsten Road

Northbrook, IL 60062

UL Standard reference number

Title

17-08

Vent or Chimney Connector Dampers for Oil-fired Appliances

58-96

Steel Underground Tanks for Flammable and Combustible Liquids-with Revisions through July 1998

80-07

Steel Tanks for Oil-burner Fuel

103-10

Factory-built Chimneys for Residential Type and Building Heating Appliances

127-08

Factory-built Fireplaces

174-04

Household Electric Storage Tank Water Heaters-with Revisions through November 2005

181-05

Factory-made Air Ducts and Air Connectors

181A-05

Closure Systems for Use with Rigid Air Ducts and Air Connectors

181B-05

Closure Systems for Use with Flexible Air Ducts and Air Connectors

217-06

Single- and Multiple-station Smoke Alarms

263-03

Standards for Fire Test of Building Construction and Materials

325-02

Standard for Door, Drapery, Gate, Louver and Window Operations and Systems-with Revisions through February 2006

343-08

Pumps for Oil-burning Appliances

441-10

Gas Vents

508-99

Industrial Control Equipment-with Revisions through July 2005

536-97

Flexible Metallic Hose-with Revisions through June 2003

641-95

Type L, Low-temperature Venting Systems-with Revisions through August 2005

651-05

Schedule 40 and Schedule 80 Rigid PVC Conduit and Fittings

723-08

Standard for Test for Surface Burning Characteristics of Building Materials

726-95

Oil-fired Boiler Assemblies-with Revisions through March 2006

727-06

Oil-fired Central Furnaces

729-03

Oil-fired Floor Furnaces

730-03

Oil-fired Wall Furnaces

732-95

Oil-fired Storage Tank Water Heaters

737-07

Fireplaces Stoves

790-04

Standard Test Methods for Fire Tests of Roof Coverings

795-06

Commercial-industrial Gas Heating Equipment.

834-04

Heating, Water Supply and Power Boilers-Electric

896-93

Oil-burning Stoves-with Revisions through May 2004

923-08

Microwave Cooking Appliances

959-01

Medium Heat Appliance Factory-built Chimneys-with Revisions through September 2006

1040-96

Fire Test of Insulated Wall Construction-with Revisions through June 2001

1256-02

Fire Test of Roof Deck Construction.

1261-01

Electric Water Heaters for Pools and Tubs-with Revisions through June 2004

1453-04

Electronic Booster and Commercial Storage Tank Water Heaters

1479-03

Fire Tests of Through-penetration Firestops

1482-10

Solid-fuel-type Room Heaters

1715-97

Fire Test of Interior Finish Material-with Revisions through March 2004

1738-10

Venting Systems for Gas-burning Appliances, Categories II, III and IV

1777-07

Standard for Chimney Liners

1995-05

Heating and Cooling Equipment.

2017-08

Standard for General-purpose Signaling Devices and Systems-with Revisions through June 2004

2034-08

Standard for Single- and Multiple-station Carbon Monoxide Alarms.

2158A-10

Outline of Investigation for Clothes Dryer Transition Duct

Underwriters' Laboratories of Canada

7 Underwriters Road Toronto,

Ontario, Canada M1R 3B4

ULC Standard reference number

Title

CAN/ULC S 102-10

Standard Methods for Test for Surface Burning Characteristics of Building Materials and Assemblies

United States - Federal Trade Commission

600 Pennsylvania Avenue NW

Washington, DC 20580

US-FTC Standard reference number

Title

CFR Title 16 Part 460

R-value Rule

Window & Door Manufacturers Association

1400 East Touhy Avenue, Suite 470

Des Plaines, IL 60018

WDMA Standard reference number

Title

AAMA/WDMA/CSA

  

101/I.S2/A440-08

Specifications for Windows, Doors and Skylights

Effective: 07/01/2014
R.C. 119.032 review dates: 01/01/2018
Promulgated Under: 119.03
Statutory Authority: 3781.10(A) , 4104.43(A)(1)
Rule Amplifies: 3781.01 , 3781.06 , 3781.10 , 3781.11 , 3791.04 , 4740.14
Prior Effective Dates: 5/27/06, 1/1/08, 3/31/08(Emer.), 6/24/08, 1/1/09, 1/1/13